Search Results

As part of an ongoing technical collaboration between Ford and Rouge Steel Company, a comprehensive study of door slam event was undertaken. The experimental phase of the project involved measurements of accelerations at eight locations on the outer panel and strains on six locations of the inner panel. Although slam tests were conducted with window up and window down, results of only one test is presented in this paper. The CAE phase of the project involved the development of suitable “math” model of the door assembly and analysis methodology to capture the dynamics of the event. The predictability of the CAE method is examined through detailed comparison of accelerations and strains. While excellent agreement between CAE and test results of accelerations on the outer panel is obtained, the analysis predicts higher strains on the inner panel than the test. In addition, the tendency of outer panel to elastically buckle is examined.

The automobile industry is seeing an increased need for the application of plastics and their derivatives in various forms such as fiber reinforced plastics, in the design and manufacture of various automotive structural components, to reduce weight, cost and improve fuel efficiency. A lot of effort is being directed at the development of structural plastics, to meet specific automotive requirements such as stiffness, safety, strength, durability and environmental standards and recyclability. This paper presents the concept of reinforcing large injection molded fiber reinforced body panels with structural uni-directional fibers (carbon, graphite, kevlar or fiber glass) wound in tension around the body panels by filament winding technique. Structural uni-directional fibers in tension wound around the fiber reinforced plastic inner body panels would place these body panels under compression.

Powertrain mounts are one of the important design characteristics of a vehicle. Powertrain is mostly mounted to the front subframe and once installed in a vehicle, powertrain mounting has an important role in determining the vehicle vibration characteristics. A good mounting system isolates engine input vibration from the vehicle body and minimizes the effect of road inputs to the customer. This paper discusses results of several dynamic models as they relate to noise, vibration and harshness (NVH) and compares the accuracy of these models. Various powertrain models are studied and their accuracy in comparison with full a vehicle model is discussed.

The scope of this paper is to describe how system level NVH targets are cascaded down to sub system level targets using the technique of Transfer Path Analysis (TPA). In the early stages of a vehicle design program target vehicles for the new vehicle are selected based on their subjective Noise, Vibration, and Harshness (NVH) performance. A reference vehicle for the new product will be selected which will be used as a baseline vehicle for the whole vehicle program. Noise and vibration measurements will be taken on both the reference and target vehicles under multiple load conditions. The simulation target for the new product will be derived from the measurements of reference vehicle, measurements of target vehicle, and the simulation of reference vehicle model. Reverse Transfer Path Analysis tools will be used to quantify the subsystem targets for the new vehicle based on the simulation targets and design intent simulation models of new product.

Conventional car manufacturing is extremely capital and energy-intensive. Due to these limitations, major auto manufacturers produce very similar, if not virtually identical, vehicles at very large volumes. This limits potential customization for different users and acts as a barrier to entry for new companies or production techniques. Better understanding of the barriers for low volume production and possible solutions with innovative production techniques is crucial for making low volume vehicles viable and accelerating the adoption of new production techniques and lightweight materials into the competitive marketplace. Additive manufacturing can enable innovative design with minimal capital investment in tooling and hence should be ideal for low and perhaps high volume parts. For this reason, it was desired to evaluate potential opportunities in manufacturing automotive parts with additive techniques.

Sunroof is placed in certain high-end vehicles to give user a better driving experience. All automakers are searching alternatives to reduce weight and cost in the vehicle, in which sunroofs are also impacted. Some alternatives are already applied, as a honeycomb paper used in some sunshades that presents benefits, as less weight and with a good cost reduction. Although, due the reduced weight for this part produced in this material, it shows more susceptibility to reproduce the vibration that vehicle propagates in movement, especially in bad condition roads. The sunroof assembly is dependent of the roof reinforcement and roof skin, but in this special case, the validation could be done in the components itself because the interaction of the sunshades is directly dependent of the other sunroof parts, as rails and front frame.

The growing competition of the automotive market makes more and more necessary the reduction of development time and consequently, the increase of the capacity to quickly respond to the launching of the competitors. One of the most costly phases on the vehicle development process is the field durability test, both in function of the number of prototypes employed and the time needed to its execution. More and more diffused, the fatigue life prediction methods have played an important part in the durability analysis via CAE. Nevertheless, in order they can be reliable and really being able to reduce the development time and cost, they need to be provided with load cases that can accurately represent the field durability tests. This work presents a CAE approach used for light trucks in order to get a reasonable understanding of component durability behavior due to payload increase. In general, road load data is not available for a new payload condition.

The U.S. Environmental Protection Agency, U.S. Department of Transportation's National Highway and Traffic Safety Administration, and the California Air Resources Board have recently released proposed new regulations for greenhouse gas emissions and fuel economy for light-duty vehicles and trucks in model years 2017-2025. These proposed regulations intend to significantly reduce greenhouse gas emissions and increase fleet fuel economy from current levels. At the fleet level, these rules the proposed regulations represent a 50% reduction in greenhouse gas emissions by new vehicles in 2025 compared to current fleet levels. At the same time, global growth, especially in developing economies, should continue to drive demand for crude oil and may lead to further fuel price increases. Both of these trends will therefore require light duty vehicles (LDV) to significantly improve their greenhouse gas emissions over the next 5-15 years to meet regulatory requirements and customer demand.

Computer applications have been widely used to assist product design. The successes and sophistication of computer aided engineering (CAE) techniques are respectfully recognized in this field. CAE applications in the manufacturing area however are still developing, although the manufacturing community is increasingly starting to pay attentions to computer simulations in its daily workings. This paper will briefly introduce some of these applications and promote awareness of computer simulations in manufacturing area. It contains four main sections: finite element analysis (FEA) in machining fixture design, FEA applications in component assembly, machining process simulations and machining vibrations in the milling operation. Each section comes with a practical case study, potential benefits are identified and conclusions are presented by using an integrated design and analysis approach.

The Ethanol-Boosted Direct Injection (EBDI) demonstrator engine is a collaborative project led by Ricardo targeted at reducing the fuel consumption of a spark-ignited engine. This paper describes the design challenges to upgrade an existing engine architecture and the synergistic use of a combination of technologies that allows a significant reduction in fuel consumption and CO₂ emissions. Features include an extremely reduced displacement for the target vehicle, 180 bar cylinder pressure capability, cooled exhaust gas recirculation, advanced boosting concepts and direct injection. Precise harmonization of these individual technologies and control algorithms provide optimized operation on gasoline of varying octane and ethanol content.

A finite element methodology, based on implicit numerical integration procedure, for simulating oil-canning tests on Door assemblies is presented. The method takes into account nonlinearities due to geometry, material and contact between parts during deformation. The simulation results are compared with experimental observations. Excellent correlation between experimental observations and analytical predictions are obtained in these tests. Armed with the confidence in the methodology, simulations on a door assembly are conducted to study the gage and grade sensitivities of the outer panel. The sensitivity studies are conducted on three different grades of steel for the outer panel. Further studies are conducted to understand the effects of manufacturing (forming operation) on the oil canning behavior of door assembly. Results demonstrate the utility of the method in material selection during pre-program design of automotive structures.

OEMs are investigating opportunities to reduce vehicle mass, driven by a need to meet upcoming CAFE targets, increase the range and reduce battery size of EVs. A number of lightweight materials including high strength steels, aluminum alloys, plastics and composites are now in production. To facilitate development of corporate R&D and commercialization plans for new materials, it is beneficial to understand the current manufacturing costs for production components, and their impact on piece price at different volumes. This paper investigates design and cost impact of light-weighting with respect to front door and floor assembly of Toyota Corolla and BMW i3. Toyota Corolla has a traditional steel body and is sold in high volumes while BMW i3 has relatively low annual sales and is primarily made of composite, aluminum and plastic parts.

Noise and vibration signals which are stationary are frequently analyzed for frequency content using Fourier Transform methods. Frequency content can be clearly displayed, but temporal characteristics of signals can easily be obscured in a frequency spectrum. Several commonly available methods of analyzing nonstationary signals are available, such as short-time Fourier Transform and wavelet analysis. Smearing of data in the time and/or frequency domains leads to limited usefulness of these methods in analyzing rapidly varying signals. This also applies to stationary signals with perceivable temporal characteristics. The Wigner Distribution is a time-frequency analysis which can analyze rapidly varying signals and show the effects of rapid changes in signal characteristics. It is appealing because it fully preserves all the information present in the original signal.

In response to environmental and fossil fuel usage concerns, the automotive industry will gradually move from Hybrid Electric Vehicles (HEV) which includes a shift of internal combustion engines toward Zero Emissions Vehicles (ZEV). Refinement is an important aspect in the successful adoption of any new technology and ZEV brings its own NVH challenges owing to the unique dynamic characteristics of the powertrain and driveline system. This paper presents considerations for addressing dynamic driveline NVH issues that are common to 100% electric vehicles; issues that manifest themselves as groans, rattles and clunks. A dynamic torsional analytical model of the powertrain & driveline will be presented. The analytical model served as the baseline for an extensive parametric study using the Genetic Algorithm (GA) technique, whereby the effectiveness of practical countermeasures was investigated.

This paper is related to a new concept for the steering linkage of light trucks featuring mono-beam front axles. The current configuration of steering systems for those vehicles comprise a worm and sector steering with a Pitman arm connected to a transverse drag link. This last one connects to the steering link that finally steers the left and right wheels. The problem that has been experienced with this system is that, during a braking event, results in a very unfavorable bump steering condition.

The work carried out with external noise insulation has been demanding high importance in vehicle concept since the second External Noise Regulation in Brazil (Conama 001/ 1993). The engineering effort shall increase significantly for near future developments due to the new Regulation (Conama 272 / 2000) with more stringent limits. The effect over vehicle systems beyond noise requirements is not restricted to the addition of shields and insulators. The airflow restriction created by the noise shields surfaces may become a huge cooling issue. This situation is usually observed on trucks designed for tropical markets and submitted to severe environments. Lessons learned in a current development are the basis of the proposed methodology. Vehicle and lab sound intensity noise source ranking tests are suggested as development tools. The paper also presents a pass-by-noise development strategy that includes CAE airflow and cooling management tools.

A newly-proposed hydroforming design of front rail was evaluated for product feasibility. Hydroforming and associated prebending and preforming processes were designed with the assistance of CAE tool. Optimized processing parameters were selected and the entire manufacturing process was simulated using FEA software. Potential manufacturing issues were identified and product modification was suggested accordingly.

This paper presents an integrated design/simulation/test approach for evaluating the sound quality of exhaust noise as early as possible in the exhaust system design and development process. A time domain engine/exhaust simulation program is used to calculate the engine order content of the tailpipe radiated noise from an odd fire V-10 exhaust system. Both steady state and transient conditions are simulated and sound files generated for exhaust sound quality evaluation. To increase the realism of played back sounds, the predicted engine orders are mixed with synthesized or recorded background noise for both steady state and transient conditions. These alternative approaches will be described and evaluated for technical feasibility and sound quality.

Advanced material modeling was conducted to describe the thermal-mechanical behavior of Boron Steel during hot stamping, a process in which blanks at 900 °C are formed and quenched between cold dies. Plastic deformation, thermal dilatation and phase transformation were incorporated in the constitutive model and a user-defined subroutine was developed to interface with LS-DYNA. Simulation was conducted on the hot stamping process of a door intrusion beam to gain insight into the physics of the process. Results showed significant influence of the thermal cycle on final product. It was also demonstrated that the program developed can be used as an early feasibility tool to determine baseline processing parameters and to detect potential defects in products without physical prototyping.

The sound field in a vehicle is one of the most complex environments being a mixture of multiple, correlated and uncorrelated sound sources. The simulation of vehicle interior sound has traditionally been produced by combining multiple test results where the influence of one source is enhanced while the other sources are suppressed, such as towing the vehicle on a rough surface for road noise, or measuring noise in a wind tunnel. Such methods are costly and provide inherent inaccuracies due to source contamination and lack of synchronization between sources. In addition they preclude the addition of analytical predictions into the simulation. The authors propose an alternative approach in which the component sounds are decomposed or separated from a single operating measurement and which provide the basis for accurate sound synthesis.