Search Results

Automobile rubber isolator was subjected to random load cycle for a long time in the service process, and its main rubber material for vibration isolation was prone to fatigue failure. Since the traditional Miner damage theory overlooked the load randomness, it had a prediction error problem. In order to improve the prediction accuracy of rubber fatigue life, the traditional Miner damage theory was modified by random uncertainty theory to predict the rubber fatigue life under random load. Firstly, the rubber dumbbell-shaped test column, which was vulcanized from rubber materials commonly used in vibration isolators, was taken as the research object. The uniaxial fatigue test of rubber under different strain amplitudes and strain mean values was carried out. Then the fatigue characteristic curve of rubber with equivalent strain amplitude as the damage parameter was established.

The durability road test of a vehicle is an important test to verify the reliability of vehicle components. In order to carry out the durability bench test for drive shaft systems of all-terrain vehicles, a method for acquiring time domain signals of articulation angles of the CVJ, input torque, and rotational speeds of drive shaft systems is proposed. The acquired load spectrum of drive shaft systems is preprocessed including deleting small amplitudes, de-drifting, deburring, filtering, etc. Peaks and valleys are extracted from the preprocessed load spectrum. Based on the graphic method and the estimator stabilization method, the upper and lower thresholds of the time domain extrapolation of the load spectrum are determined, and then the peaks and valleys excesses that exceed the upper and lower thresholds are extracted. The generalized pareto distribution function is used to fit the distribution of peaks and valleys excesses.

Because the power unit of electric vehicle has large torque, the rubber mount of electric vehicle is fully compressed under the condition of full throttle acceleration. When designing the mount of electric vehicle, the dynamic-to-static stiffness ratio of mount under the case should be as low as possible to improve the vibration isolation rate of the mount. In this paper, a method for calculating the high frequency dynamic characteristics of rubber isolators under different preloads is presented. Firstly, the dynamic characteristics of rubber specimens under various shear pre-strains were tested. The test results show that the dynamic stiffness of specimen decreases at first and then increases with the increase of shear strain. The viscoelastic parameters of rubber in frequency domain under different pre-strain were identified according to the experimental data. Secondly, a finite element modeling method was proposed.

Tortuosity, viscous characteristic length and thermal characteristic length are three important parameters for estimating the acoustic performance of porous materials, and it is usually measured by ultrasonic measurement technology, which is costly. In this paper, a method for identifying the tortuosity, viscous characteristic length and thermal characteristic length for the porous fiber materials mixed with kapok fiber and two kinds of other fiber materials is proposed. The tortuosity is calculated by using the porosity and high-frequency normal sound absorption coefficient of porous materials. According to the normal sound absorption coefficient curve of porous materials under plane wave incidence, viscous characteristic length and thermal characteristic length are identified through the Johnson-Champoux-Allard-Lafarge (JCAL) model and genetic algorithm by using the measured parameters, the calculated tortuosity and static thermal permeability.

A ball joint is an important component of the automotive drive shaft system, as well the contact stress inside the ball joint is an important optimization goal in the design of ball joints. At present, the analysis of the contact stress inside the ball joint mainly focuses on the static contact stress analysis. The static contact stress analysis, however, cannot reflect the change of the contact stress inside the ball joint. In order to analyze the contact stress of the ball joint more effectively, a hybrid flexible and rigid bodies dynamics (HFRBD) model of the ball joint for studying the dynamic contact stress inside the ball joint is proposed. In the HFRBD model, the balls are regarded as the rigid body, while the cage, the inner race and the outer race are regarded as the flexible body. The contact parameters of the contact pairs in the model are determined on the basis of Hertz contact theory.

A new proportional electromagnetic dynamic vibration absorber (EDVA) is proposed for control of engine vibration during idling. The device consists of an electromagnetic actuator attached to the primary structure through elastic element, where the driving force pair is implemented between the reaction-mass and the primary structure. The design of the proportional electromagnetic actuator is realized considering the geometric parameters of the core to achieve nearly constant magnetic force over a broad range of its dynamic displacement but proportional to square of the current. A methodology is proposed to achieve magnetic force proportional to square of current and consistent with the disturbance frequency. The proportional EDVA is subsequently applied to a single-degree-of-freedom primary system with an acceleration feedback control algorithm for attenuation of primary system vibration in a frequency band around the typical idling vibration frequencies.

A fourth-order mathematical model for I-EHB (integrated electro-hydraulic brake) system was derived from its mechanical and hydraulic subsystems. The model was linearized at equilibrium state and then was verified by AMESIM software. The friction model of the system was analyzed based on static friction and viscous friction. A bench test was designed to identify the parameters of friction model. As the I-EHB system worked at different braking conditions, a PID-based switching controller was designed to track the target servo cylinder pressure. Both simulations and experiments results showed that, the response time of pressure was less than 120ms, and there was no overshoot, which helped handling different braking conditions and improving the braking safety and comfort.

In order to enhance the efficiency of durability testing of automobile parts, a time-frequency domain accelerated editing method of road load time series of rubber mount on powertrain was discussed. Based on Stockwell Transform method and Accumulative Power Spectral Density, a new time-frequency domain accelerated editing method (ST-APSD) was proposed. The accumulative power spectral density was obtained by ST of the load time series signal of automobile powertrain rubber mounting force which is acquired by the real vehicle in the test field. Based on the accumulative power spectral density, the threshold value was proposed to identify and delete the small damage load fragments, and then the acceleration spectrum was obtained.

Sliding mode control with a disturbance observer (SMC-DO) is proposed for suppressing the sprung mass vibration in a quarter-car with double-wishbone active suspension system (ASS), which contains the geometry structure of the upper and lower control arms. The governing equations of double-wishbone ASS are obtained by the balance-force analysis of the sprung mass in ASS. Considering uncertainties in damping, stiffness, and external disturbance acting on the sprung mass, we design a disturbance observer based on a sliding mode control (SMC) to estimate these uncertainties under the unknown road excitation. By the Lyapunov minimax approach, the uniform boundedness and the uniform ultimate boundedness of ASS with the proposed control are rigorously proved. Through co-simulation of ADAMS software and MATLAB/Simulink software, the sprung mass acceleration of ASS can be obtained with and without the proposed control.

To study the generated axial force (GAF) of the drive shaft system more accurately and effectively, this paper introduces the interval uncertainty into the research focusing on the GAF. Firstly, an interval uncertainty model for calculating the GAF is proposed based on the Chebyshev polynomials and an analytical model of the GAF. The input torque, the articulation angle, the rotation angle of the drive shaft system, the pitch circle radius (PCR) of the tripod joint and the friction coefficient are regarded as interval variables. Secondly, the upper and lower bounds of the proposed GAF model under interval uncertainty parameters are calculated quickly with the vertex method. Then the interval uncertainty optimization of the GAF under uncertainty parameters is performed. The upper bound of the response interval of the GAF is taken as the optimization object.

An Inline 4-cylinder engine is equipped with second-order balance shafts. When the engine is running under no-load acceleration conditions, the gear system of the balance shaft generated whine noise. In this paper, an analysis and experiment method for reducing the whine noise is presented. First, a flexible multi-body dynamic model of the engine is established, which includes shaft and casing deformation, micro-modification of the gears. Taking the measured cylinder pressure as input, the load on each gear of balance shaft gear system is calculated. In addition, the influence of tooth surface micro-modification on the meshed noise was analyzed. The results show that the dynamic meshing force between the crank gear and the shim gear is large under the original tooth surface micro-modification parameters, which is the main reason of the whine noise.

The tripod constant velocity joint (CVJ) has been widely used in mechanical systems due to its strong load-bearing capacity, high efficiency, and reliability. It has become the most commonly used plunging-type CVJ in automotive drive-shaft. A generated axial force (GAF) with a third-order characteristic of driven shaft speed is caused by the internal friction and motion characteristics in a tripod joint. The large GAF has a negative impact on the NVH (Noise, Vibration, and Harshness) characteristics of automobiles, and this issue is particularly prominent in new energy vehicles. A multi-body dynamic model of the Adjustable Angular Roller (AAR) tripod CVJ is developed to calculate and analyze the GAF. To describe the internal motion of the AAR tripod CVJ, the contact interactions between the roller and the track or the trunnion were modeled using non-linear equivalent spring-damping models for contact collision forces and modified Coulomb friction model for friction.

A model for a generic layout of an engine front end accessory drive system is established. The dynamic performances of the system are obtained via a numerical method. The dynamic performances consist of the oscillation angle of tensioner arm, the slip ratio of each pulley and the dynamic belt tension. In modeling the system, the hysteretic behavior of an automatic tensioner, the loaded torque of the accessory pulley versus the engine speed, the torsional vibration of crankshaft and the creep of the belt are considered. The dynamic performances of the system at steady state and under accelerating condition are analyzed. An example is provided to validate the established model. The measured results show that the torsional vibration of crankshaft is larger and the dynamic performances of the system are different under accelerating conditions, though the acceleration is small.

During the operation of the automotive drive shaft system, the ball-type universal joint will generate a secondary torque, which will affect the torque transmission of the automotive drive shaft system and the comfort of the automobile. Under the influence of the internal friction of the ball-type universal joint, the secondary torque generates a torque component on the plane where the working angle is located and the plane perpendicular to the working angle. To effectively calculate and analyze the secondary torque, this paper establishes a multi-body dynamic model of the ball-type universal joint. At the same time, the secondary torque of the ball-type universal joint is measured by the NVH multi-function test bench, which verifies the validity of the multi-body dynamic model. In order to improve the analysis efficiency of the secondary torque, a proxy model of the secondary torque of the ball-type universal joint is established based on the multi-body dynamic model.

A road test on semi-trailers is carried out, and accelerations of some characteristic points on the braking system,axles,and truck body is measured,also brake pressure and noise around the support frame is acquired.The measured data was analyzed to determine the causes of the brake noise, and the mechanism of the noise of the drum brake of semi-trailers during low-speed braking was investigated. The following conclusions are obtained: (1) Brake noise of the drum brake of the semi-trailer at low-frequency is generated from vibrations of the brake shoes, axle, and body, and the vibration frequency is close to 2nd natural frequency of the axle. (2) Brake noise is generated from stick-slip motion between the brake shoes and the brake drum, where the relative motion between the brake drum and the brake shoes is changed alternately with sliding and sticking, resulting in sudden changes in acceleration and shock vibration.

In this paper, the influence of the decoupler-cage structure on the hitting noise of the hydraulic mount is studied, the abnormal noise of the hydraulic mount is mainly caused by the collision impact between the decoupler and the cage, the hitting noise was simulated and evaluated using calculation and experiment. a finite element model of the collision impact between the decoupler and the cage is developed, and an explicit finite element analysis is performed to obtain the time history of the vibration acceleration of the model, which is used as the boundary condition of the noise analysis. The acoustic boundary element method is used to analyze the impact noise of the decoupler-cage, and the frequency domain distribution characteristics of the impact sound pressure are obtained. The influence of different decoupler structure on the hitting noise is studied, and the recommended values for each parameter for a structure are given.

The automatic tensioner is an important component of the engine front end accessory drive system (EFEADS). It maintains the tension of the belt steadily and reduces the slip of pulley, which is benefit for improving the life of V-ribbed belt. In this paper, an EFEADS model is established which is considering with the hysteretic behavior and the asymmetry of friction damping of a tensioner. A four-pulley EFEADS is taken as a study subject. The dynamic responses of system, such as the oscillation angle of each pulley, the slip factor of pulley, the oscillation of tensioner arm and the dynamic belt tension are analyzed with symmetric damping and asymmetric damping tensioner. Meanwhile, the influence of asymmetric damping factors of tensioner on the dynamic response of EFEADS is also investigated.

Tuned mass dampers (TMD) are frequently used in vehicles to resolve vibration and interior booming noise issues arising from powertrain's vibration and road excitation. This paper describes a driveshaft NVH case study in which analysis and test were used to solve the NVH problem. A TMD simulation package that utilizes a database of measured elastomeric material propertied. This facilitates the designing of optimized damper systems for a wide variety of vehicle applications. The simulation software takes into account frequency effects on elastomer properties while designing dampers. And the approach has proven to accurately predict performance in vehicles prior to manufacture. Rules of thumb for TMD design are discussed including locations for placement of dampers in automotive structures, determining the needed mass, and measurements and simulations that can greatly improve the success and reducing time-cost for TMD design.

A dynamic performance calculating model for a powertrain-subframe mounting system (PSMS) is presented. Calculation methods for determining the dynamic displacements of a powertrain center of gravity (CG), the dynamic displacements of a subframe CG and the dynamic reaction forces of each mount in a PSMS under ground and motor shake excitation are developed in this paper. An optimization procedure based on the genetic algorithm and SQP is developed for reducing resonance peaks of the reaction forces at mounts. A generic PSMS with three powertrain-subframe mounts and four subframe-body mounts is used to validate the optimization method. The optimization results demonstrate that the results using the optimization procedure can effectively reduce the reaction forces at mounts.

Considering the interaction between fan blades and the surrounding air when a cooling fan rotates, the Fluid-Structure Interaction (FSI) model of the fan is established, and flow rate, static pressure, efficiency versus speed of the fan are calculated and analyzed. The aerodynamic performance of the fan is carried out, and the measured performance parameters are compared with calculated to validate the developed model. Using the established model, the performance of fans with different rotating speeds, diameters and blade installation angles is calculated. The effects of fan speed, diameter and blade installation angle on blade deformation and aerodynamic performance are studied.