Search Results

Water injection is an effective method for knock control in spark-ignition engines. However, the requirement of a separate water source and the cost and complexity associated with a fully integrated system creates a limitation of this method to be used in volume production engines. The engine exhaust typically contains 10-15% water vapor by volume which could be condensed and potentially stored for future use. In this study, the exhaust condensate composition was assessed for its use as an effective replacement for distilled water. Specifically, condensate samples were collected pre and post-three-way catalyst (TWC) and analyzed for acidity and composition. The composition of the pre and post-TWC condensates was found to be similar however, the pre-TWC condensate was mildly acidic. The mild acidity has the potential to corrode certain components in the intake air circuit.

A 13 L HD diesel engine was converted to run as a flame propagation engine using the HEDGE™ Dual-Fuel concept. This concept consists of pre-mixed gasoline ignited by a small amount of diesel fuel - i.e., a diesel micropilot. Due to the large bore size and relatively high compression ratio for a pre-mixed combustion engine, high levels of cooled EGR were used to suppress knock and reduce the engine-out emissions of the oxides of nitrogen and particulates. Previous work had indicated that the boosting of high dilution engines challenges most modern turbocharging systems, so phase I of the project consisted of extensive simulation efforts to identify an EGR configuration that would allow for high levels of EGR flow along the lug curve while minimizing pumping losses and combustion instabilities from excessive backpressure. A potential solution that provided adequate BTE potential was consisted of dual loop EGR systems to simultaneously flow high pressure and low pressure loop EGR.

SwRI has developed the DCO® ignition system, a unique continuous discharge system that allows for variable duration/energy events in SI engines. The system uses two coils connected by a diode and a multi-striking controller to generate a continuous current flow through the spark plug of variable duration. A previous publication demonstrated the ability of the DCO system to improve EGR tolerance using low energy coils. In this publication, the work is extended to high current (≻ 300 mA/high energy (≻ 200 mJ) coils and compared to several advanced ignition systems. The results from a 4-cylinder, MPI application demonstrate that the higher current/higher energy coils offer an improvement over the lower energy coils. The engine was tested at a variety of speed and load conditions operating at stoichiometric air-fuel ratios with gasoline and EGR dilution.

As on-highway, heavy-duty diesel engine designs have evolved to meet tighter emissions specifications and greater customer requirements, the crankcase environment for heavy-duty engine lubricants has changed. Engine lubricant quality is very important to help ensure engine durability, engine performance, and reduce maintenance downtime. Beginning in the late 1980's, a new Mack genuine oil specification and a new American Petroleum Institute (API) heavy-duty engine lubricant category have been introduced with each new U.S. heavy-duty, on-highway emissions specification. This paper documents the history and development of the Mack T-7, T-8, T-8A, T-8E, T-9, T-10, T-11, and T-12 engine lubricant tests.

This paper describes the design and functionality of an in-situ air entrainment measuring device for analysis of the air entrainment and air release properties of lubricating fluids. The apparatus allows for a variety of measurement techniques for the aeration and deaeration of the lubricating fluid at various temperatures, pressures, and agitation speeds. This test apparatus is patent pending because of its unique ability to allow for continuous, in-situ measurement of the fluid properties and the rates of change of these properties. Most other measurement techniques and apparatuses do not allow for uninterrupted measurement. This apparatus is also unique in that it is capable of detecting minor fluid density changes at a lower level and with more accuracy than all other current techniques or apparatuses.

The automotive sector is rapidly transitioning to decarbonized, electric vehicles solutions. However, due to challenges with such rapid adoption, Internal combustion engines (ICE) are expected to be used for decades to come. In this transition period it is important to continue to improve ICE efficiency. A key design parameter to increase ICE efficiency is the compression ratio. For gasoline engines, the compression ratio is limited so as to avoid knock. Engine designers can employ several strategies to mitigate knock and enable higher compression ratios. In this study, a new methodology has been developed to compare various knock mitigation strategies. By comparing the knock limited load at a given combustion phasing the expected compression ratio increase can be inferred.

Next generation vehicles are under environmental and economic pressure to reduce emissions and increase fuel economy, while maintaining the same ride and performance characteristics of present day combustion engine automobiles. This has prompted researchers to investigate hybrid vehicles as one possible solution to this challenge. At Southwest Research Institute (SwRI), a unique parallel hybrid drivetrain was designed and prototyped. This hybrid drivetrain alleviates the disadvantages of series hybrid drivetrains by directly coupling the driving wheels to two power sources, namely an engine and an electric motor. At the same time, the design allows the engine speed to be decoupled from the vehicle speed, allowing the engine to operate at its most efficient state. This paper describes the drivetrain, its components, and the test stand that was assembled to test the parallel hybrid drivetrain.

It has been shown within the catalyst industry that the emission performance with higher cell density technology and therefore with higher specific geometric area is improved. The focus of this study was to compare the overall performance of high cell density catalysts, up to 1600cpsi, using a MY 2001 production vehicle with a 4.7ltr.V8 engine. The substrates were configured to be on the edge of the design capability. The goal was to develop cost optimized systems with similar emission and back pressure performance, which meet physical and production requirements. This paper will present the results of a preliminary computer simulation study and the final emission testing of a production vehicle. For the pre-evaluation a numerical simulation model was used to compare the light-off performance of different substrate designs in the cold start portion of the FTP test cycle.

Enhancement of fuel/air mixing is one path towards enabling future diesel engines to increase efficiency and control emissions. Air-assist fuel injections have shown potential for low pressure applications and the current work aims to extend air-assist feasibility understanding to high pressure environments. Analyses were completed and carried out for traditional high pressure fuel-only, internal air-assist, and external air-assist fuel/air mixing processes. A combination of analytical 0-D theory and 3D CFD were used to help understand the processes and guide the design of the air-assisted setup. The internal air-assisted setup was determined to have excellent liquid fuel vaporization, but poorer fuel dispersion than the traditional high-pressure fuel injections.

A turbocharged 2.0 L PFI engine was modified to operate in a low-pressure loop and Dedicated EGR (D-EGR®) engine configuration. Both engine architectures were operated with a low and high octane gasoline as well as three ethanol blends. The core of this study focused on examining combustion differences at part and high loads between the selected fuels and also the different engine configurations. Specifically, the impact of the fuels on combustion stability, burn rates, knock mitigation, required ignition energy, and efficiency were evaluated. The results showed that the knock resistance generally followed the octane rating of the fuel. At part loads, the burn rates, combustion stability, and EGR tolerance was marginally improved with the high ethanol blends. When combustion was not knock or stability limited, the efficiency differences between the fuels were negligible. The D-EGR engine was much less sensitive to fuel changes in terms of burn rates than the LPL EGR setup.

Usage of CVTs in automotive applications has begun to increase, however because of their relative newness and previous usage in nonautomotive applications, a broad base of technical information on the various types of CVT's does not exist. Most importantly though, no comparison information exists on the different types of configurations. Currently, there are a number of CVT technologies that have been used in automotive, off-road and industrial applications. This paper will highlight the characteristics, design limitations and efficiencies of the following basic CVT types:

1Increasing adoption of downsized, boosted, spark-ignition engines has improved vehicle fuel economy, and continued improvement is desirable to reduce carbon emissions in the near-term. However, this strategy is limited by damaging preignition events which can cause hardware failure. Research to date has shed light on various contributing factors related to fuel and lubricant properties as well as calibration strategies, but the causal factors behind an individual preignition cycle remain elusive. If actionable precursors could be identified, mitigation through active control strategies would be possible. This paper uses artificial neural networks to search for identifiable precursors in the cylinder pressure data from a large real-world data set containing many preignition cycles. It is found that while follow-up preignition cycles in clusters can be readily predicted, the initial preignition cycle is not predictable based on features of the cylinder pressure.

This paper describes a distributed digital process control computer designed for large industrial processing plants that has been applied successfully to laboratory engine testing. Over the past two years several complete systems have been installed and adapted to control engines from 75 kW to over 1800 kW with various dynamometer/generator absorption devices. Control problems encountered, and solutions we have found, are discussed along with the wide range of capabilities this type of system can provide. A short comparison is made between distributed digital control systems and mini-computers, listing advantages and disadvantages of both.

The U.S. Army has long identified the need for rapid, reliable methods for analysis of fuels and lubricants on or near the battlefield. The analysis of fuels and lubricants under battlefield or near-battlefield conditions requires that the equipment be small, portable, rugged, quick, and easy to use. Over the past 15 to 20 years, several test kits and portable laboratories have been developed in response to this need. One instrumental technique that has been identified as a likely candidate to meet this need is near-infrared spectroscopy (NIR). To evaluate NIR as a candidate, a set of 280 fuel samples was used. This sample set contained samples of diesel fuel grades 1 and 2, Jet A-l, JP-5, and JP-8. Inspection data were collected on all the fuels as sample size permitted. Each sample was then scanned using a near-infrared spectrometer. Data analysis, model building, and calibration were conducted using a software package supplied with the instrument.

Since the turn of the millennium, automated vehicle technology has matured at an exponential rate, evolving from research largely funded and motivated by military and agricultural needs to a near-production market focused on everyday driving on public roads. Research and development has been conducted by a variety of entities ranging from universities to automotive manufacturers to technology firms demonstrating capabilities in both highway and urban environments. While this technology continues to show promise, corner cases, or situations outside the average driving environment, have emerged highlighting scenarios that impede the realization of full automation anywhere, anytime. This paper will review several of these corner cases and research deficiencies that need to be addressed for automated driving systems to be broadly deployed and trusted.

Internal combustion engines (ICE) will be a part of personal transportation for the foreseeable future. One recent trend for engines has been downsizing which enables the engine to be run more efficiently over regulatory drive cycles. Due to downsizing, engine power density has increased which leads to problems with engine knock. Therefore, there is an increasing need to find a means to reduce the knock propensity of downsized engines. One of the ways of reducing knock propensity is by introducing Exhaust Gas Recirculation (EGR) into the combustion chamber, however, volumetric efficiency also reduces with EGR which places challenges on the boosting system. The individual benefits of high-pressure (HP-EGR) and low-pressure (LP-EGR) loop EGR system to assist the boosting system of a 2.0 L Gasoline Direct Injection (GDI) production engine are explored in this paper.

It is widely acknowledged that the CFR octane rating engines are not representative of modern engines and that there is a gap in the quantification of knock severity between the two engine types. As part of a comprehensive study of the autoignition of different fuels in both the CFR octane rating engines and a modern, direct injection, turbocharged spark-ignited engine, a series of fuel blends were tested with varying composition, octane numbers and ethanol blend levels. The paper reports on the fourth part of this study where cylinder pressures were recorded under standard knock conditions in CFR engines under RON and MON conditions using the ASTM prescribed instrumentation. By the appropriate signal conditioning of the D1 detonation pickups on the CFR engines, a quantification of the knock severity was possible that had the same frequency response as a cylinder pressure transducer.

Life prediction and reliability analysis of a cam roller system were investigated. From the tribological analysis, the cam roller system was found to operate under low film parameter conditions and components were subjected to the risk of contact fatigue. Surface analysis performed on the failed rollers indicated that the surface distress was the primary cause for failure. Then, numerical analyses were performed to evaluate the cam roller life and its related reliability. The adopted approach combined a contact fatigue crack growth calculations with a probabilistic model for controlling the design uncertainty. The computation-efficient Fast Probabilistic Integration (FPI™) code was used to solve the problem. With appropriate descriptions for uncertainty distributions, the surface fatigue life of the specified cam roller system can be predicted along with a confident reliability level.

To aid in the catalytic converter design and development process, a test apparatus was designed and built which will allow comparative evaluation of the durability of candidate mat materials under highly controlled thermal and vibration environments. The apparatus directly controls relative shear deflection between the substrate and can to impose known levels of mat material strain while recording the transmitted shear force across the mat material. Substrate and can temperatures are controlled at constant levels using a resistive thermal exposure (RTE) technique. Mat material fatigue after several million cycles is evident by a substantial decrease in the transmitted force. A fragility test was found to be an excellent method to quickly compare candidate materials to be used for a specific application. Examples of test results from several materials are given to show the utility of the mat material evaluation technique.

Particle number concentrations and size distributions were measured for the diluted exhaust of a 1991 diesel engine during the US FTP transient cycle for heavy-duty diesel engines. The engine was operated on US 2-D on-highway diesel fuel. The particle measurement system consisted of a full flow dilution tunnel as the primary dilution stage, an air ejector pump as the secondary dilution stage, and an electrical low pressure impactor (ELPI) for particle size distribution measurements. Particle number emission rate was the highest during the Los Angeles Non Freeway (LANF) and the Los Angeles Freeway (LAF) segments of the transient cycle. However, on brake specific number basis the LAF had the lowest emission level. The particle size distribution was monomodal in shape with a mode between 0.084 μm and 0.14 μm. The shape of the size distribution suggested no presence of nanoparticles below the lower detection limit of the instrument (0.032 μm), except during engine idle.