Search Results

A prototype 2007 ISL Cummins diesel engine equipped with a diesel oxidation catalyst (DOC), diesel particle filter (DPF), variable geometry turbocharger (VGT), and cooled exhaust gas recirculation (EGR) was tested at Southwest Research Institute (SwRI) under a high-load accelerated durability cycle for 1000 hours with B20 soy-based biodiesel blends and ultra-low sulfur diesel (ULSD) fuel to determine the impact of B20 on engine durability, performance, emissions, and fuel consumption. At the completion of the 1000-hour test, a thorough engine teardown evaluation of the overhead, power transfer, cylinder, cooling, lube, air handling, gaskets, aftertreatment, and fuel system parts was performed. The engine operated successfully with no biodiesel-related failures. Results indicate that engine performance was essentially the same when tested at 125 and 1000 hours of accumulated durability operation.

A novel continuous inductive discharge ignition system has been developed that allows for variable duration ignition events in SI engines. The system uses a dual-coil design, where two coils are connected by a diode, combined with the multi-striking coil concept, to generate a continuous current flow through the spark plug. The current level and duration can be regulated by controlling the number of re-strikes that each coil performs or the energy density the primary coils are charged to. Compared to other extended duration systems, this system allows for fairly high current levels during the entire discharge event while avoiding the extremely high discharge levels associated with other, shorter duration, high energy ignition systems (e.g. the plasma jet [ 1 , 2 ], railplug [ 3 ] or laser ignition systems [ 4 , 5 , 6 , 7 , 8 ].

SwRI has developed the DCO® ignition system, a unique continuous discharge system that allows for variable duration/energy events in SI engines. The system uses two coils connected by a diode and a multi-striking controller to generate a continuous current flow through the spark plug of variable duration. A previous publication demonstrated the ability of the DCO system to improve EGR tolerance using low energy coils. In this publication, the work is extended to high current (≻ 300 mA/high energy (≻ 200 mJ) coils and compared to several advanced ignition systems. The results from a 4-cylinder, MPI application demonstrate that the higher current/higher energy coils offer an improvement over the lower energy coils. The engine was tested at a variety of speed and load conditions operating at stoichiometric air-fuel ratios with gasoline and EGR dilution.

A series of ignition systems were evaluated for their suitability for high-EGR SI engine applications. Testing was performed in a constant-volume combustion chamber and in a single-cylinder research engine, with EGR rates of up to 40% evaluated. All of the evaluated systems were able to initiate combustion at a simulated 20% EGR level, but not all of the resulting combustion rates were adequate for stable engine operation. High energy spark discharge systems were better, and could ignite a flame at up to 40% simulated EGR, though again the combustion rates were slow relative to that required for stable engine performance. The most effective systems for stable combustion at high EGR rates were systems which created a large effective flame kernel and/or a long kernel lifetime, such as a torch-style prechamber spark plug or a corona discharge igniter.

Particle number concentrations and size distributions were measured for the diluted exhaust of a 1991 diesel engine during the US FTP transient cycle for heavy-duty diesel engines. The engine was operated on US 2-D on-highway diesel fuel. The particle measurement system consisted of a full flow dilution tunnel as the primary dilution stage, an air ejector pump as the secondary dilution stage, and an electrical low pressure impactor (ELPI) for particle size distribution measurements. Particle number emission rate was the highest during the Los Angeles Non Freeway (LANF) and the Los Angeles Freeway (LAF) segments of the transient cycle. However, on brake specific number basis the LAF had the lowest emission level. The particle size distribution was monomodal in shape with a mode between 0.084 μm and 0.14 μm. The shape of the size distribution suggested no presence of nanoparticles below the lower detection limit of the instrument (0.032 μm), except during engine idle.

The primary goal of this project was to characterize particulate emissions from a snowmobile engine through measurement of particulate matter volatile organic fraction (VOF), particle size, and biological activity. Emissions were evaluated using both a mineral oil and a biosynthetic oil. Basic criteria pollutants were also measured from diluted exhaust using conventional techniques. Particulate matter volatile organic fraction was determined using a gas chromatographic method (DFI/GC). Particle size was characterized using a scanning mobility particle sizer (SMPS), and particulate matter biological activity was measured using a modification of the Ames bioassay procedure. Results revealed that more than 99 percent of the particles were ultrafine (Dp<100nm), with a peak concentration in the nanoparticle (Dp<50nm) size range. It was also observed that the use of a biosynthetic lubricant increased both volatile and total PM mass emissions compared to the mineral lubricant.

Comparative exhaust emission tests were performed with five diesel fuels, namely a Sasol Fischer-Tropsch diesel, a fuel meeting the CARB diesel fuel specification, a fuel meeting the US 2-D diesel fuel specification, and two blends of the Fischer-Tropsch diesel and the 2-D diesel. Hot-start and cold-start heavy-duty transient emission tests were performed using a 1999 model year DDC series 60 engine. Regulated exhaust emissions with the Fischer-Tropsch diesel were significantly lower than with the 2-D and CARB diesel fuels, in both the hot-start and cold-start tests. When compared with test results obtained previously with a 1991 engine, it was found that the reduction in NOX with the Fischer-Tropsch fuel was smaller in the 1999 engine, while the reduction in PM was greater.

The use of high levels of EGR has been documented to increase fuel efficiency and reduce emissions of spark ignition engines [1–5]. However, these engines typically face challenges in EGR control and tolerance, which can reduce the expected efficiency improvement. A concept developed by Southwest Research Institute explores the potential of an engine with individual cylinders dedicated to EGR production to overcome the challenges associated with EGR tolerance and control. In this study, a 4-cylinder engine was run with cylinder 1 exhausting directly to the intake manifold, leading to a constant 25% EGR level. The engine was run naturally aspirated over a large portion of the performance map at an ultra-high (14:1) compression ratio. As a part of the study, air-to-fuel ratio in cylinder 1 was varied from stoichiometric to rich to determine the effect of the products of partial combustion on EGR tolerance and fuel consumption.

This paper summarizes the Heavy-Duty In-Use Testing (HDUIT) measurement allowance program for Particulate Matter Portable Emissions Measurement Systems (PM-PEMS). The measurement allowance program was designed to determine the incremental error between PM measurements using the laboratory constant volume sampler (CVS) filter method and in-use testing with a PEMS. Two independent PM-PEMS that included the Sensors Portable Particulate Measuring Device (PPMD) and the Horiba Transient Particulate Matter (TRPM) were used in this program. An additional instrument that included the AVL Micro Soot Sensor (MSS) was used in conjunction with the Sensors PPMD to be considered a PM-PEMS. A series of steady state and transient tests were performed in a 40 CFR Part 1065 compliant engine dynamometer test cell using a 2007 on-highway heavy-duty diesel engine to quantify the accuracy and precision of the PEMS in comparison with the CVS filter-based method.

A solid particle number measurement system (SPNMS) was developed using a catalytic stripper (CS) technology instead of an evaporation tube (ET). The ET is used in commercially available systems, compliant with the Particle Measurement Program (PMP) protocol developed for European Union (EU) solid particle number regulations. The catalytic stripper consists of a small core of a diesel exhaust oxidation catalyst. The SPNMS/CS met all performance requirements under the PMP protocol. It showed a much better performance in removing large volatile tetracontane particles down to a size well below the PMP lower cut-size of 23 nm, compared to a SPNMS equipped with an ET instead of a CS. The SPNMS/CS also showed a similar performance to a commercially available system when used on a gasoline direct injection (GDI) engine exhaust.

Horiba on-board diesel exhaust particulate sampler (OBS-PM) is a filter based partial flow particulate sampling system used for On-board diesel particulate matter (PM) measurement. It takes sample from either raw or diluted exhaust. It can run at constant dilution ratios or at variable dilution ratios with proportional control on the sample flow. The diluted exhaust moves through a pre-weighed 47 mm particulate filter and PM is collected on the filter. By weighing the loaded sample filter, PM emission from the engine or the vehicle can be determined. The performance of the OBS-PM meets most of requirements for a real-time partial flow sample system (PFSS) recommended by ISO 16183 [2]. The physical size and the power consumption of the instrument are minimized. It is powered with four 12 volts batteries, and can be installed on a vehicle for real-world PM emission evaluation.

Gasoline direct injected (GDI) engines are becoming a concern with respect to particulate matter (PM) emissions. The upcoming 2014 Euro 6 regulations may require a drastic reduction in solid particle number emissions from GDI engines and the proposed California Air Resources Board (CARB) LEV III regulations for 2014 and 2017 will also require some PM reduction measures. As a result, it is necessary to characterize PM emissions from GDI engines and investigate strategies that suppress particle formation during combustion. The main focus of this work was on using exhaust gas recirculation (EGR) as a means to reduce engine-out particle emissions from a GDI engine with an overall stoichiometric fuel to air mixture. A small displacement, turbocharged GDI engine was operated at a variety of steady-state conditions with differing levels of EGR to characterize total (solid plus volatile) and solid particle emissions with respect to size, number, and soot or black carbon mass.

The addition of exhaust gas recirculation (EGR) has demonstrated the potential to significantly improve engine efficiency by allowing high CR operation due to a reduction in knock tendency, heat transfer, and pumping losses. In addition, EGR also reduces the engine-out emission of nitrogen oxides, particulates, and carbon monoxide while further improving efficiency at stoichiometric air/fuel ratios. However, improvements in efficiency through enhanced combustion phasing at high compression ratios can result in a significant increase in cylinder pressure. As cylinder pressure and temperature are both important parameters for estimating the durability requirements of the engine - in effect specifying the material and engineering required for the head and block - the impact of EGR on surface temperatures, when combined with the cylinder pressure data, will provide an important understanding of the design requirements for future cylinder heads.

The emission performance of a 1997 Mercedes OM 366 LA medium heavy-duty diesel engine and a 1998 Detroit Diesel Corporation (DDC) Series 60 heavy heavy-duty diesel engine was investigated using the US EPA hot-start transient cycle using different candidate diesel fuels developed by the Empresa Nacional Del Petroleo (ENAP), the state-owned oil production and refining company of Chile. The aim of the work was to identify a clean diesel fuel that can be readily produced and reduces emissions from diesel engines in Chile, particularly in Santiago Metropolitan Area where air pollution is a serious problem. Using a Mercedes engine of the type found in Chile, several candidate fuel formulations were tested in both the Mercedes and DDC engines to identify leading candidate formulations that would effectively reduce emission in both traditional and modern technology engines.

The use of cooled EGR in gasoline engines improves the fuel efficiency of the engine through a variety of mechanisms, including improving the charge properties (e.g. the ratio of specific heats), reducing knock and enabling higher compression ratio operation and, at part loads conditions in particular, reducing pumping work. One of the limiting factors on the level of improvement from cooled EGR is the ability of the ignition system to ignite a dilute mixture and maintain engine stability. Previous work from SwRI has shown that, by increasing the ignition duration and using a continuous discharge ignition system, an improved ignition system can substantially increase the EGR tolerance of an engine [1, 2]. This improvement comes at a cost, however, of increased ignition system energy requirements and a potential decrease in spark plug durability. This work examines the impact of engine operating parameters on the ignition energy requirements under high dilution operation.

The U.S. EPA and the California Air Resources Board have adopted standards to reduce emissions from recreational marine vessels. Existing regulations focus on reducing hydrocarbons. There are no regulations on particulate emissions; particulate is expected to be reduced as a side benefit of hydrocarbon control. The goal of this study was to develop a sampling methodology to measure particulate emissions from marine outboard and personal watercraft engines. Eight marine engines of various engine technologies and power output were tested. Emissions measured in this program included hydrocarbons, carbon monoxide, oxides of nitrogen. Particulate emissions will be presented in a follow-up paper.

High dilution engines have been shown to have a significant fuel economy improvement over their non-dilute counterparts. Much of this improvement comes through an increase in compression ratio enabled by the high knock resistance from high dilution. Unfortunately, the same reduction in reactivity that leads to the knock reduction also reduces flame speed, leading to the engine becoming unstable at high dilution rates. Advanced ignition systems have been shown to improve engine stability, but their impact is limited to the area at, or very near, the spark plug. To further improve the dilute combustion, a system in which a microwave field is established in the combustion chamber is proposed. This standing electric field has been shown, in other applications, to improve dilution tolerance and increase the burning velocity.

Nanoparticle formation during exhaust sampling and dilution has been examined using a two-stage micro-dilution system to sample the exhaust from a modern, medium-duty diesel engine. Growth rates of nanoparticles at different exhaust dilution ratios and temperatures have been determined by monitoring the evolution of particle size distributions in the first stage of the dilution system. Two methods, graphical and analytical, are described to determine particle growth rate. Extrapolation of size distribution down to 1 nm in diameter has been demonstrated using the graphical method. The average growth rate of nanoparticles is calculated using the analytical method. The growth rate ranges from 6 nm/sec to 24 nm/sec, except at a dilution ratio of 40 and primary dilution temperature of 48 °C where the growth rate drops to 2 nm /sec. This condition seems to represent a threshold for growth. Observed nucleation and growth patterns are consistent with predictions of a simple physical model.

Total and solid particle mass, size, and number were measured in the dilute exhaust of a 2009 vehicle equipped with a gasoline direct injection engine along with an exhaust three-way-catalyst. The measurements were performed over the FTP-75 and the US06 drive cycles using three different U.S. commercially available fuels, Fuels A, B, and C, where Fuel B was the most volatile and Fuel C was the least volatile with higher fractions of low vapor pressure hydrocarbons (C10 to C12), compared to the other two fuels. Substantial differences in particle mass and number emission levels were observed among the different fuels tested. The more volatile gasoline fuel, Fuel B, resulted in the lowest total (solid plus volatile) and solid particle mass and number emissions. This fuel resulted in a 62 percent reduction in solid particle number and an 88 percent reduction in soot mass during the highest emitting cold-start phase, Phasel, of the FTP-75, compared to Fuel C.

This work included design and fabrication of a particle free exhaust gas recirculation element (PF-EGR-E) that included two concentric tubes, one for a clean air stream and the other for a simulated exhaust stream. The inner tube was a perforated tube to allow molecular diffusion between the two streams. The design and dimension of the PF-EGR-E was guided with the help of theoretical prediction of gas and particle diffusion. The goal was to build a PF-EGR-E that retains particles in a dilute exhaust stream while allowing maximum molecular exchange with the air stream. The performance of the PF-EGR-E was investigated using dilute diesel engine exhaust and clean air flowing in parallel at different flow and temperature levels.