Search Results

As for automobile, the mass production period of Electric Vehicle(EV) has begun by the rapid progress of the battery performance. But for EV- Motorcycle(MC), it is limited for the venture companies' releases. The design and evaluation methodologies are not yet established or standardized so far. This paper provides the practical and the experimental examples. To study the feasibility of EV-MC, we developed the prototypes in the present technical and suppliers' parts environments, and evaluated them by the practical view of the MC usage. The developed EV-MC has the equivalent driving performance of the 250cc internal combustion engine(ICE)-MC and a cruising range of 100km in normal use. In the prototype development, the reliability and the ability of protection design of the battery in the whole vehicle against the environmental loads are mainly studied, especially, heat and cold, water, shock, and the accident impact.

The Advanced ECS is under development for the purpose of saving fuel, improving safety, and cabin comfort. In FY2006 study, basic components (i.e. MDC, OBNOGS, desiccant units, and CO2 removers) have been improved and their performances evaluated including resistance to environmental condition (i.e. vibration). In addition, the suitable system configuration for a 90-seats aircraft has been considered to evaluate the feasibility of the system. In this paper, we show the results of the evaluated performances based on prototype components, and the analytical study of a revised system configuration.

“ASKA” developed by National Aerospace Laboratory (NAL) is a quiet, short take-off and landing (QSTOL) research aircraft adopting upper surface blowing (USB) concept as a powered high lift system. To achieving sufficient STOL performance by augmenting stall angle of attack and roll control power, blowing BLC technique was applied to the outboard leading edges and ailerons.Supplied high pressure air to save the BLC piping space,the BLC system which was fit for use of high pressure air was developed. The BLC system, in which BLC air is discharged by a series of discrete jets from small drilled holes (0.8 ∼ 3.0 mm in diameter) arranged in a raw, is one of the unique features of the aircraft. In this paper, the summaries of aerodynamic development of the BLC system are described except for the air piping system.

As the social aaareness of the need for greater automobile safety has risen, autonolive parts manufacturers have focused a lot of new research and development to aulomotive brake systems. Aith the much rapid advances and steady cost reductions in microelectronics technology, highly reliable, electronically controlled lour-thee1 antilock brake systems (ABS) are beginning to gain broad acceptance. Horever, wide acceptance of ABS depends upon the system and having superior performance, and high reliability at an affordable price. The toothed wheels (sensor rings) used for measuring the wheel velocity in the ABS require high precision in the pitch error of the teeth and specific magnetic properties in order to accurately detect wheel velocity, which is the first signal for brake control. Moreover, as these sensor rings are located close to the wheel, they require increased corrosion resistance ability higher than any other automotive parts.

At the upstream part of the Three-Way Catalyst (TWC) an O₂ sensor (UpO₂S) is used for O₂ Feedback Control (O₂F/B) that controls the air-fuel ratio (A/F) close to the stoichiometric level. O₂ sensor has a bit of individual characteristic difference as for the switching the excess air ratios of output (λ shift). This phenomenon becomes remarkable according to the effects of unburnt elements in exhaust gas. Despite the O₂F/B implementation, A/F isn't controlled to the stoichiometric level and the conversion efficiency of the TWC could be lower. Maintaining a higher level of TWC conversion efficiency requires more accurate A/F control and corrections of the UpO₂S λ shift issue. Therefore, using an O₂ sensor at the downstream part of the TWC (DownO₂S)~where the effects of unburnt elements in exhaust gas are smaller~can be an effective way to restore these challenges.

In this study, we efficiently predict the vibration response of a design shape at a low computational cost in the early development stage, select design proposals with good characteristics from many proposals devised by the designer at the early stage, and forward them to the next stage to achieve the front-loading of development while increasing product value. The application of participation factor (PF) focusing on the response at a specific part for vibration evaluation of a motorcycle frame is described. To reduce the motorcycle frame vibration, an eigenvalue analysis was performed, and appropriate design change proposals were efficiently selected using partial participation factor (PPF), an index showing the relevance of vibration of specific parts or positions. Using the PPF, we extracted which vibration modes considerably contribute to the vibration response of the part of interest.

This technical paper reports the development of an automatic defect detector utilizing deep learning for “polished skins”. Materials with a “polished skin” are used in the fabrication of the external plates of commercial airplanes. The polished skin is obtained by polishing the surface of an aluminum clad material, and they are visually inspected, which places a significant burden on inspectors to find minute defects on relatively large pieces of material. Automated inspection of these skins is made more difficult because the material has a mirror finished surface. Defects are broadly classified into three categories: dents, bumps, and discolorations. Therefore, a defect detector must be able to detect these types of defects and measure the defects’ surface profile. This technical paper presents details related to the design and manufacture of an inexpensive automated defect detector that demonstrates a sufficiently high level of performance.

This paper describes an Automobile Navigation System with Multi-Source Guide Information. One of the features of this system is accurate location detection, which uses refined map-matching method incorporating a high accuracy rotation sensor, Fiber Optic Gyroscope (FOG). The system shows the position of the vehicle on a CRT map display and can also provide useful information, such as the locations of hotels, golf courses, etc., by using a CD-ROM disc. In addition to this information, this system can play CD-ROM discs based on the CDCRAFT standard. By means of this standard, software vendors can produce multimedia entertainment, such as a sightseeing guide with voice. Also, this system can display road and traffic information from the roadside radio beacons of the Vehicle Information & Communication System (VICS). This navigation system has been installed in Nissan's 1991 model Cedric, Gloria and CIMA.

Sumitomo Electric Industries (SEI), which has been producing its first generation ABS since 1987, has continued its R & D efforts to develop a second generation ABS better suited to a wider range of vehicles. A Compact ABS has been successfully developed, which has realized the smallest and lightest 3/4-channel hydraulic unit known to the authors, taking full advantage of the newly developed flow control valve.

In the closed environments, removal of trace contaminants generated from persons, animals, and plants is important function to keep the environment below the allowable level. We conducted the fundamental tests in order to confirm design of TCCA (Trace Contaminants Control Assembly) for Closed Ecology Experiment Facilities (CEEF), and obtained the following results; 1) The palladium-on-alumina catalyst is suitable for CO, CH4, C2H4 conversion at temperature lower than 400°C. 2) The alkali impregnated AC (activated charcoal) is effective for NO2, SO2 removal and prevents catalyst poisoning from SO2. 3) The active-desorbing conducted by hot air blow-throw an AC is effective for C2H5OH, CH2Cl2 desorbing. We discuss the fundamental test and design conditions for TCCA.

The Dynamic Navigation System is an information-providing type navigation and route guidance system. Fundamentally the system is suited for phased implementation. Some measures, however, must be taken in advance to enhance it to the advanced phase. For these measures, information providing data formats, travel time collection methods and small-delay system architecture have been studied. As a result, the flexible data composition for information provision, the on-board travel time measurement for efficient and accurate data collection and the autonomous communication network concept called ‘HYPO NET’ have been proposed.

From the viewpoint of reducing the environmental impacts by automobile emission, improving fuel efficiency is essential. That is why automobiles need to be lightened. However, more and more electrical systems have been necessary in an automobile to ensure safety and comfort. With the increase in the number of electrical systems, the weight of Electrical Distribution System (EDS) also has become increased. In order to reduce the weight of EDS, it was decided to evaluate a change of material from copper to aluminum. In fact, aluminum wires have been used for high-voltage wires, but they have almost never been used for low-voltage wires. SUMITOMO ELECTRIC GROUP developed an aluminum wire that is available for low-voltage wire harnesses and started mass production of the wire from October 2010. In this paper, I'm reporting mainly on our development of a new aluminum alloy that can be used for aluminum wires.

Pollution is worsening in cities. The exhaust gas from vehicles is the main cause of air pollution in cities. The major drawback of the diesel engine is the Particulate Matter (PM) contained in the exhaust fumes which is also said to lead to cancer. For about 20 years many tests have been conducted in order to reduce PM in diesel exhaust gas. However the exhaust gas in present diesel engines contains a significant amount of PM. This is because there is no practical material for the Diesel Particulate Filter (DPF). Conventional ceramic materials have problems such as cracking and melting during regeneration and conventional metal materials lack adequate corrosion resistance for practical use. The authors present a new type of DPF made of metal porous matter (Celmet) which is designed with a thermal construction and simple control system in order to solve the problem of diesel exhaust gas.

In recent years, even motorcycles impose demands for engine power controls that are more flexible and precise. The Electronic Throttle Control (ETC) system is one of the methods that addresses this need. However, the most important issue facing the installation of the ETC system on the motorcycle is handling failures. To avoid this problem, we developed an ETC system for motorcycles that can properly effect engine power control in case of a failure. This ETC system contains in duplicate the major components to detect failures and switch to a failure mode properly. To effect control that is optimally suited to the type of failure, this system switches between three types of failure modes. These failure modes are designed to minimize risks in case of a failure and maximize the operational capability while the rider is on the way to have the motorcycle repaired.

The weight of wire harnesses increases with the growing number of systems used in the vehicle in recent years. For the purpose of reducing the weight of wire harnesses, aluminum instead of the conventional copper is getting popular as a wire conductor. The conventional Al wire, however, is not able to be used for small gauge wires such as the sizes of 0.35mm2 and 0.5mm2 and wires used in the engine compartment due to its insufficient conductor strength. For this reason, we tried to develop a stronger aluminum alloy that has conductor strength equivalent to or stronger than that of copper. For the first time in the industry, we have successfully developed a high-strength aluminum alloy wire. Starting with the application of 0.35mm2 wire for engine wire harnesses, we began mass production in April 2015. This paper reports the development of high-strength aluminum alloy that can be used for small gauge wires and wires used in the engine compartment.

We developed a remote control unit (Hereinafter referred to as the controller) employing mainly an eight-directional joystick with push-button function. And it has good operational feeling. As previous joysticks generated operator feeling via springs, so the click sensation could not be felt. We thought that a good click feeling can be obtained by applying rubber contacts to the switch element of the joystick. Additionally, in order to include the push-button functions, we supported the operant unit with biaxial bearing and employed a sliding-knob structure penetrating this operant unit. Also in order to obtain a uniform operator feeling for all eight directions, we applied eight rubber contacts and gave the switches eight contacts. In order to restrain the rise in IC costs with the increase to eight contacts, we introduced an eight-contact four- output switch matrix and a one-contact three-electrode pattern.

In the expansion of composite material application, it is one of the most important subjects in assembly of aircraft structure how drilling of composite/metal stack should be processed in an efficient way. This paper will show the result of development of a drill bit for CFRP/Aluminum-alloy stack by Kawasaki Heavy Industries (KHI) and Sumitomo Electric Hardmetal (SEH). In order to improve workability and economic performance, the drill bit which enables drilling CFRP/Al-alloy stack: at 1 shot; from both directions; without air blow and coolant (just usual vacuuming); was required. A best mix drill bit which has smooth multi angles edge and pointed finishing edge was produced as a result of some trials. Developed drill bit achieved required performance and contributed to large cost reduction, labor hour saving, production speed increase and work environment improvement.

With the rapid advances in electronic control within automobiles, the junction block (J/B), primarily used for electrical transmission and electrical wiring, has begun to house electronic control units. It is evolving into an active component with smart functions that also controls vehicle devices, at the core of the wiring harness. We have developed a method using CAE to predict the fatigue failure life of J/B brackets for use as a design-assist tool in the early stage of J/B development. Failure of J/B brackets starts with the repetitive stress generated in the brackets during resonance. This stress is maximum at primary natural vibration which is the lowest frequency during resonance. By accurately estimating the above-mentioned stresses using CAE, we established a method to determine the number of vibrations at which fatigue failure of the J/B bracket would occur (fatigue failure life) from the fatigue failure life characteristics of the material.

Owing to the recent developments in sensors with reduced size and weight, it is now possible to install sensors on a body of a motorcycle to monitor its behavior during running. The analysis of maneuverability and stability has been performed based on the data resulted from measurements by these sensors. The tire forces and moments is an important measurement item in maneuverability and stability studies. However, the tire forces and moments is difficult to measure directly, therefore, it is a common practice to measure the force and the moment acting on the center of the wheel. The measuring device is called a wheel forces and moments sensor, and it is widely used for cars. The development of a wheel forces and moments sensor for motorcycles has difficulty particular to motorcycles. First, motorcycles run with their bodies largely banked, which restricts positioning the sensors.

The National Space Development Agency of Japan (NASDA) is constructing the Isolation Chamber in Tsukuba Space Center (TKSC) by March 1996. The Isolation Chamber will be used to basic training for Japanese astronauts, development for crew training technology and research for manned space technology. This paper describes the outline of the Isolation Chamber.