Search Results

Fuel cells plays significant role in the automotive sector to substitute the fossil fuels and complement to electric vehicles. In the fuel cell vehicles fuel cell stack is major component. It is important to have a robust fuel cell model that can simulate the behaviour of the fuel cell stack under various operating conditions in order to study the functioning of a fuel cell and optimize its operating parameters and achieve the best efficiency in operation. The operating voltage of the fuel cell at different current densities depends upon thermodynamic parameters like temperature and pressure of the reactants as well factors like the state of humidification of the electrolyte membrane. A 1D model is developed to capture the variation in voltage at different current densities due to internal losses and changes to operating conditions like temperature and pressure.

The automotive engineering fraternity is facing tremendous challenges to improve fuel economy and emissions of the internal combustion engine. The stringent CAFÉ standards for CO2 emissions are expected to become further demanding as time progresses. Indian OEM engineering experts have been considering various technology options to improve vehicle fuel economy. However, the time and costs associated with the development of these strategies and technologies remains a point of major concern and challenge. The potential of a technology to reduce fuel consumption can be estimated in three basic ways. One approach involves developing an actual prototype engine and vehicle with the technologies under evaluation, performing the actual measurements. Some variability from test to test is although expected, this method is the most accurate but time consuming and very expensive.

In recent years due to significant increased cost of raw material, fuel and energy, vehicle cost is increased. As vehicle cost is one of the major factors that attracts prospective buyers, it has created specific demand for low weight and low-cost components than traditional components with better performance to meet customer expectations. Suspension is one of the critical aggregates where lot of material is used and reduction in weight tends to give lot of cost benefit. As suspension system derives vehicle’s handling performance, it has to be ensured that handling performance of vehicle is maintained the same or made better while reducing weight of the suspension. Advancements in simulation capabilities coupled with manufacturing technology has enabled development non-traditional leaf springs. One of such springs is mono-leaf spring without shackle. This type of leaf spring provides advantages such as low weight and nonlinear stiffness.

At present, all automobile manufacturers are fighting climate change through various emission reduction approach. In vehicle Brake system, one of the major factor which contributes to vehicle tail pipe emission in residual brake drag. A residual brake drag shall be defined as the resistance torque produced by brake in brake released condition. In Caliper brake assemblies which is a commonly used foundation brake, to reduce residual drag, low drag caliper is used. Low drag in caliper is achieved using positive retraction clip and increased caliper piston seal roll back. In general residual drag is measured in static test condition and there is no standard test procedure to assess residual drag in dynamic condition. Vehicle manufactures pays higher price for this low drag caliper owing to its benefit towards vehicle emission reduction.

Vehicles have a wide range of resonance band due to design nature & characteristics of its aggregates. First order, vehicle speed dependent, wheel disturbance due to wheel imbalances can result in excitation of different vehicle aggregates. Steering wobble refers specifically to first order road wheel excitation effects, in frequency range of 10-16 Hz, that manifest themselves as significant steering wheel torsional vibrations at highway speeds i.e. at the range of 80 km/h to 120 km/h on smooth roads. The tire, being an elastic body analogous to an array of radial springs, may exhibit variations in stiffness about its circumference; hence, it may vibrate at different frequencies due to wheel imbalance. This paper introduces dynamic steering wobble analysis methodology either using vehicle speed at Discrete (individual speeds) or by Sweep (low to high speed) method to investigate steering wobble in the virtual environment using the full vehicle MBD model.

Electric vehicles are fast expanding in market size, and there are increasing customer expectations on all aspects of the vehicle, including its noise and vibrational characteristics. Irritable noise from traction motors account for around 15% of the overall noise in an electric vehicle, and thus, has a need to be analysed and studied. This study focuses on identifying the critical vibro - acoustic orders for an 8 pole PMSM (Permanent Magnet Synchronous Motor) for three cases - healthy, with static eccentricity and with dynamic eccentricity. PMSM motors are widely used for traction and other applications due to their higher power density along with compact size. A coupled approach between electromagnetic and vibro - acoustic simulation is deployed to characterise the NVH behaviour of the motor.

The sunrise vision for hydrogen economy lies in efficient, lightweight and durable devices which can convert hydrogen energy into electrical energy. Proton Exchange Membrane fuel cell (PEMFC) is a key hydrogen energy conversion system for transport sector. The efficiency and durability of PEM fuel cell largely depends on cathode electrode and membrane and Bipolar plates (BP Plates) plays an important role in it. BP plates perform the important functions of transporting fuel gases to reactive sites, collecting charges and thus conducting electricity from cell to cell, moisture adjustment of membrane, transport of produced water and provides essential mechanical strength to fuel cell stack. It makes BP plates the backbone of PEM Fuel cell power stack. For BP plates to perform intended functions, it is highly desirable BP plates to possess excellent properties on corrosion resistance, electrical conductivity, thermal conductivity, water wettability, weldability and formability.

The Common Rail fuel injection System (CRS) has completely changed the whole diesel engine combustion cloud dynamics and enhanced the applicability of diesel engines further with a motto of providing a more cleaner sky and greener earth. The most cutting-edge technological developments made in CRS and EGT system enables OEMs to achieve further more stringent emission norms and adopt the environmental protection compliances. Today’s CRS systems are the most advanced generation fuel injection systems providing further high injection pressures, wide multiple injections capability with shorter dwell periods enabling real smoother Digital Rate Shaping (DRS) and injection control that benefits not only the engine combustion performance but also enables smarter thermal management of modern exhaust systems while meeting stringent emission compliances and achieving future CO2 reductions goal.

Nowadays, E- commerce and logistics business model is booming in India with road transport as a major mode of delivery system using containers. As competition in such business are on rise, different ways of improving profit margins are being continuously evolved. One such scenario is to look at reducing transportation cost while reducing fuel consumption. Traditionally, aero dynamics of commercial vehicles have never been in focus during their product development although literature shows major part of total fuel energy is consumed in overcoming aerodynamic drag at and above 60 kmph in case of large commercial vehicle. Hence improving vehicle exterior aerodynamic performance gives opportunity to reduce fuel consumption and thereby business profitability. Also byproduct of this improvement is reduced emissions and meeting regulatory requirements.

In regions like Indian Subcontinent, Gulf or Saharan & Sub-Saharan Africa, where the sunshine is abundant almost all year round, air-conditioning is an important aspect of vehicles (passenger cars, buses etc.). Higher heat means higher cooling demand which in turn means bigger AC system. Like other auxiliaries, AC compressor is a parasitic load on the engine. The best way to beat heat and reduce cabin heat load is to stop heat build-up itself. The present paper explores one such means of reducing cabin heat build-up by leveraging latent heat properties of phase change materials and thus improving the air condition performance. With the help of a case study this paper aims at detailing comprehensive effect of phase change material (PCM) and its application on the heat build-up inside the cabin of a vehicle, the air conditioning cooling performance, the time required to achieve comfort temperature, work of compression performed by AC compressor and COP.

This paper documents the approach followed to simulate the physical phenomenon of thermistor based AC compressor Cut-OFF/Cut-IN (AC compressor cycling) in 1-Dimensional Computer Aided Engineering (1D CAE) to enable Mobile Air Conditioning (MAC) performance prediction at different ambient conditions. Thermistor based AC compressor cycling logic is incorporated in MAC systems to prevent ice formation at evaporator core and liquid refrigerant flow to AC compressor. Currently, during MAC system performance simulation over a transient drive cycle, the 1D models are able to predict cabin cooldown performance for severe ambient conditions (>40°C, high solar load) with >95% accuracy, as in these cases AC compressor cycling due to thermistor doesn’t occur at higher ambient.

The future of bus transit in new millennium is promising. This optimism is based on an anticipated long-term slowdown in growth of suburbs and revitalization of central cities. It reflects and escalates the public concern with traffic congestion, sprawl and pollution. This calls for double the use of public transport to address above issues. It calls for changing the mind-set of society towards public transports like buses, coaches etc. This could happen if bus design ensures right comfort, safety and TCO by ensuring refined bus transport. Hence, it is responsibility of OEMs to provide the new generation buses and coaches, which will ensure the public demands of comforts in terms of NVH refinement. This paper covers the unique approach used to convert the existing bus NVH refinement to next level as a short-term solution and with the intention of articulating NVH strategies for new generation bus development.

Methane (CH4) is main constituent of compressed natural gas (CNG). CNG is compressed to less than 1% of the volume, which it occupies at atmospheric pressure. CNG contains almost 70% to 90% methane, one of the most significant greenhouse gas contributing directly into climate change. The effects caused due to gas leakages that results in fire and bursting of cylinder can be prevented by continuous monitoring of gas leakage in the Gas transmission pipeline of the commercial vehicles. In order to detect the methane leaks and resolve as early as possible, effective sensors need to be researched, analyzed and developed. This paper discusses about the usage of sensor with digital output replacing the previous gas leak detection sensor module, which gives analog output. The previously used Gas leakage detection module implements a design of a gas leakage detector system with, LED and audio indication that notifies the leakage in gas to the users.

In recent years, there has been a rapid growing demand for laser brazing in the transportation industry for automotive-Body in White (BIW), steel sheet assembly. Implementation of laser brazing is aimed primarily to improve productivity, quality of joints and cost. Laser brazing works by filling the opening amongst two substrates by melting the filler wire with the help of laser beam (used as a heat source), whereas in conventional resistance spot welding, contacting metal surface points are joined by the heat obtained from resistance to electric current. BIW is essentially a welded metal structure which is meant to provide durability and crashworthiness to the vehicle and is conventionally assembled using resistance spot welding process. The BIW structure comprises of various steel grades having varying thicknesses, compositions, microstructures and mechanical properties.

Leaf springs are used for vehicle suspension to support the load. These springs are made of flat sections of spring steel in single or in stack of multiple layers, held together in bracketed assembly. The key characteristics of leaf spring are defined as ability to distribute stresses along its length and transmit a load over the width of the chassis structures. The most common leaf spring steels are carbon steels alloyed with Cr and micro-alloyed with Ti, V and Nb. The specific thermomechanical process and alloying elements result in specific strength and fatigue properties for spring steels. The unique properties which facilitate use of spring steel in leaf spring suspensions are ability to withstand considerable twisting or bending forces without any distortion. The microstructure of these steel determines the performance and reflects the process of steel manufacturing. The performance is mainly determined by evaluating fatigue life durability.

The small commercial vehicle business is driven by demand in logistic, last mile transportation and white goods market. And to cater these businesses operational and safety needs, they require closed container on vehicle. As of now, very few OEM’s provide regulatory certified container vehicle because of constrains to meet inertia class of the vehicle. This paper focuses on design of a durable and extremely reliable container, made of the low-cost economy class glass fibre & core material. The present work provides the means to design the composite container for the N1 category of the vehicle. The weight of after-market metal container ranges between 300-350 Kg for this category of vehicle, which affects the overall fuel economy and emission of the vehicle. A detailed CAE analysis is done to design composite container suitable to meet inertia class targets and to achieve weight reduction of 30-40% as compared to metal container.

Hybridization with engine downsizing is a regular trend to achieve fuel economy benefits. However this leads to a development of new downsized engine which is very costly and time consuming process, also engine downsizing demands for expensive higher power electric system to meet performance targets. Various techniques like gear ratio optimization, reducing number of gears, battery size and control functionalities optimization have been evaluated for maximum fuel economy keeping system cost very low and improving vehicle performance. With optimized gear ratios and reduced number of gears for parallel hybrid, it is possible to operate the engine in the best efficiency zones without downsizing. Motor is selected based on power to weight ratio, gradient requirements, improved acceleration performance and top speed requirement of vehicle in EV mode.

The goal of reducing fuel consumption and CO2-Emission is leading to turbo-charged combustion engines that deliver high torque at low speeds (down speeding). To meet NVH requirements damper technologies such as DMF (Dual Mass Flywheel) are established, leading to reduced space for the clutch system. Specific measures need to be considered if switching over from SMF (Single Mass Flywheel) to DMF [8]. Doing so has an impact on thermal behavior of the clutch system, for example due to reduced and different distribution of thermal masses and heat transfer to the surroundings. Taking these trends into account, clutch systems within vehicle powertrains are facing challenges to meet requirements e.g. clutch life, cost targets and space limitation. The clutch development process must also ensure delivery of a clutch system that meets requirements taking boundary conditions such as load cycles and driver behavior into account.

Shock loads/Jerk is a major cause of gearbox failure which occurs during abusive driving condition. In passenger car torque spikes are experienced by the transmission during launch/sudden clutch release events on flat road or off-road. Whereas, in case of commercial vehicle torque spikes are generated while operation in mines and off-road application especially in tipper vehicles. Torque spikes experienced by the gearbox can lead to gear failure, gear slippage and structural failure of housing. Research has been done till now to improve the design of gearbox to address such failures. However, with increased focus on transmission downsizing and improved vehicle performance (by weight reduction and more powerful engine) it is necessary to have optimum design to meet transmission life. This paper discuss the test setup and methodology used to simulate the torque spikes on test bench. To develop the test procedure huge data was collected on commercial vehicles.

In a current competitive automotive market, weight and cost optimization is the need of an hour. Therefore it is important to explore use of alternative material which has less weight, low manufacturing cost and better strength. This paper presents methodology to achieve cost & weight reduction through use of Austempered Ductile Iron (ADI) instead of alloy forging. ADI casting has lower density, physical properties at par with alloy forgings and lower manufacturing cost. Pivot arm is the one of the critical component of twin axle steering system which transfers the hydraulic torque from steering gearbox to second forward axle via linkage system. In order to design lightweight pivot arm, existing chromium alloy steel material is replaced with the Austempered ductile iron (ADI). Pivot arm is designed and validated digitally as well as bench test and results are found to be meeting cost and weight targets.