Search Results

Fuel cells plays significant role in the automotive sector to substitute the fossil fuels and complement to electric vehicles. In the fuel cell vehicles fuel cell stack is major component. It is important to have a robust fuel cell model that can simulate the behaviour of the fuel cell stack under various operating conditions in order to study the functioning of a fuel cell and optimize its operating parameters and achieve the best efficiency in operation. The operating voltage of the fuel cell at different current densities depends upon thermodynamic parameters like temperature and pressure of the reactants as well factors like the state of humidification of the electrolyte membrane. A 1D model is developed to capture the variation in voltage at different current densities due to internal losses and changes to operating conditions like temperature and pressure.

The automotive engineering fraternity is facing tremendous challenges to improve fuel economy and emissions of the internal combustion engine. The stringent CAFÉ standards for CO2 emissions are expected to become further demanding as time progresses. Indian OEM engineering experts have been considering various technology options to improve vehicle fuel economy. However, the time and costs associated with the development of these strategies and technologies remains a point of major concern and challenge. The potential of a technology to reduce fuel consumption can be estimated in three basic ways. One approach involves developing an actual prototype engine and vehicle with the technologies under evaluation, performing the actual measurements. Some variability from test to test is although expected, this method is the most accurate but time consuming and very expensive.

At present, all automobile manufacturers are fighting climate change through various emission reduction approach. In vehicle Brake system, one of the major factor which contributes to vehicle tail pipe emission in residual brake drag. A residual brake drag shall be defined as the resistance torque produced by brake in brake released condition. In Caliper brake assemblies which is a commonly used foundation brake, to reduce residual drag, low drag caliper is used. Low drag in caliper is achieved using positive retraction clip and increased caliper piston seal roll back. In general residual drag is measured in static test condition and there is no standard test procedure to assess residual drag in dynamic condition. Vehicle manufactures pays higher price for this low drag caliper owing to its benefit towards vehicle emission reduction.

Traditionally the bushes used for automotive suspension are tested by methods which either don't address the environmental conditions including dust or mud, which convert a 2-body wear condition to 3-body wear condition prevailing in the field or not representative of the complete load bearing area of the bushes coming in contact with the pin. To address the above issues, a novel method of testing has been designed to take care of the loading type, environmental conditions and load bearing area of the bushes to simulate the field conditions.

The sunrise vision for hydrogen economy lies in efficient, lightweight and durable devices which can convert hydrogen energy into electrical energy. Proton Exchange Membrane fuel cell (PEMFC) is a key hydrogen energy conversion system for transport sector. The efficiency and durability of PEM fuel cell largely depends on cathode electrode and membrane and Bipolar plates (BP Plates) plays an important role in it. BP plates perform the important functions of transporting fuel gases to reactive sites, collecting charges and thus conducting electricity from cell to cell, moisture adjustment of membrane, transport of produced water and provides essential mechanical strength to fuel cell stack. It makes BP plates the backbone of PEM Fuel cell power stack. For BP plates to perform intended functions, it is highly desirable BP plates to possess excellent properties on corrosion resistance, electrical conductivity, thermal conductivity, water wettability, weldability and formability.

The Common Rail fuel injection System (CRS) has completely changed the whole diesel engine combustion cloud dynamics and enhanced the applicability of diesel engines further with a motto of providing a more cleaner sky and greener earth. The most cutting-edge technological developments made in CRS and EGT system enables OEMs to achieve further more stringent emission norms and adopt the environmental protection compliances. Today’s CRS systems are the most advanced generation fuel injection systems providing further high injection pressures, wide multiple injections capability with shorter dwell periods enabling real smoother Digital Rate Shaping (DRS) and injection control that benefits not only the engine combustion performance but also enables smarter thermal management of modern exhaust systems while meeting stringent emission compliances and achieving future CO2 reductions goal.

Nowadays, E- commerce and logistics business model is booming in India with road transport as a major mode of delivery system using containers. As competition in such business are on rise, different ways of improving profit margins are being continuously evolved. One such scenario is to look at reducing transportation cost while reducing fuel consumption. Traditionally, aero dynamics of commercial vehicles have never been in focus during their product development although literature shows major part of total fuel energy is consumed in overcoming aerodynamic drag at and above 60 kmph in case of large commercial vehicle. Hence improving vehicle exterior aerodynamic performance gives opportunity to reduce fuel consumption and thereby business profitability. Also byproduct of this improvement is reduced emissions and meeting regulatory requirements.

In previous work, AC Compressor Cycling (ACC) was modeled by incorporating evaporator thermal inertia in Mobile Air Conditioning (MAC) performance simulation. Prediction accuracy of >95% in average cabin air temperature has been achieved at moderate ambient condition, however the number of ACC events in 1D CAE simulation were higher as compared to physical test [1]. This paper documents the systematic approach followed to address the challenges in simulation model in order to bridge the gap between physical and digital. In physical phenomenon, during cabin cooldown, after meeting the set/ target cooling of a cabin, the ACC takes place. During ACC, gradual heat transfer takes place between cold evaporator surface and air flowing over it because of evaporator thermal inertia.

This paper documents the approach followed to simulate the physical phenomenon of thermistor based AC compressor Cut-OFF/Cut-IN (AC compressor cycling) in 1-Dimensional Computer Aided Engineering (1D CAE) to enable Mobile Air Conditioning (MAC) performance prediction at different ambient conditions. Thermistor based AC compressor cycling logic is incorporated in MAC systems to prevent ice formation at evaporator core and liquid refrigerant flow to AC compressor. Currently, during MAC system performance simulation over a transient drive cycle, the 1D models are able to predict cabin cooldown performance for severe ambient conditions (>40°C, high solar load) with >95% accuracy, as in these cases AC compressor cycling due to thermistor doesn’t occur at higher ambient.

The automotive industry is facing a challenge as efficiency improvements are required to address the strict emission norms which in turn requires high performance downsized, lightweight IC engines. The increasing demand for lightweight engine needs high strength to weight ratio materials. To meet high strength to weight ratio, castings are preferable. However due to strength limitations for critical crankshaft applications, it forces to use costly forgings such as micro alloyed forging steel and Martensitic (after heat treatment) forging steel. To reduce the cost impact, high strength Austempered Ductile iron (ADI) casting is developed for crankshaft applications to substitute steel forgings. Austempered Ductile Iron is having an excellent mechanical properties due to aus-ferritic structure. The improved properties of developed ADI Crankshaft over steel forged crankshaft offers additional weight advantage.

Methane (CH4) is main constituent of compressed natural gas (CNG). CNG is compressed to less than 1% of the volume, which it occupies at atmospheric pressure. CNG contains almost 70% to 90% methane, one of the most significant greenhouse gas contributing directly into climate change. The effects caused due to gas leakages that results in fire and bursting of cylinder can be prevented by continuous monitoring of gas leakage in the Gas transmission pipeline of the commercial vehicles. In order to detect the methane leaks and resolve as early as possible, effective sensors need to be researched, analyzed and developed. This paper discusses about the usage of sensor with digital output replacing the previous gas leak detection sensor module, which gives analog output. The previously used Gas leakage detection module implements a design of a gas leakage detector system with, LED and audio indication that notifies the leakage in gas to the users.

In recent years, there has been a rapid growing demand for laser brazing in the transportation industry for automotive-Body in White (BIW), steel sheet assembly. Implementation of laser brazing is aimed primarily to improve productivity, quality of joints and cost. Laser brazing works by filling the opening amongst two substrates by melting the filler wire with the help of laser beam (used as a heat source), whereas in conventional resistance spot welding, contacting metal surface points are joined by the heat obtained from resistance to electric current. BIW is essentially a welded metal structure which is meant to provide durability and crashworthiness to the vehicle and is conventionally assembled using resistance spot welding process. The BIW structure comprises of various steel grades having varying thicknesses, compositions, microstructures and mechanical properties.

Leaf springs are used for vehicle suspension to support the load. These springs are made of flat sections of spring steel in single or in stack of multiple layers, held together in bracketed assembly. The key characteristics of leaf spring are defined as ability to distribute stresses along its length and transmit a load over the width of the chassis structures. The most common leaf spring steels are carbon steels alloyed with Cr and micro-alloyed with Ti, V and Nb. The specific thermomechanical process and alloying elements result in specific strength and fatigue properties for spring steels. The unique properties which facilitate use of spring steel in leaf spring suspensions are ability to withstand considerable twisting or bending forces without any distortion. The microstructure of these steel determines the performance and reflects the process of steel manufacturing. The performance is mainly determined by evaluating fatigue life durability.

Corrosion in automotive industry is broadly categorized into cosmetic & perforation corrosion. Cosmetic corrosion comprises of superficial red rust which is deleterious to the overall aesthetic appeal of the vehicle but can be rectified. Perforation corrosion involves complete erosion of the panel, compromising structural integrity of the respective part. Perforation corrosion demands part replacement. In order to tackle this menace, automotive OEMs have formulated varied corrosion strategies in terms of selection of appropriate substrate, part design & surface protection scheme. Validation of various corrosion strategies become pivotal during the development phase of various parts and assemblies. Traditionally, Salt Spray Test (SST) has been used to determine corrosion life of materials/parts/assemblies. This test however does not simulate real-world conditions.

The small commercial vehicle business is driven by demand in logistic, last mile transportation and white goods market. And to cater these businesses operational and safety needs, they require closed container on vehicle. As of now, very few OEM’s provide regulatory certified container vehicle because of constrains to meet inertia class of the vehicle. This paper focuses on design of a durable and extremely reliable container, made of the low-cost economy class glass fibre & core material. The present work provides the means to design the composite container for the N1 category of the vehicle. The weight of after-market metal container ranges between 300-350 Kg for this category of vehicle, which affects the overall fuel economy and emission of the vehicle. A detailed CAE analysis is done to design composite container suitable to meet inertia class targets and to achieve weight reduction of 30-40% as compared to metal container.

Hybridization with engine downsizing is a regular trend to achieve fuel economy benefits. However this leads to a development of new downsized engine which is very costly and time consuming process, also engine downsizing demands for expensive higher power electric system to meet performance targets. Various techniques like gear ratio optimization, reducing number of gears, battery size and control functionalities optimization have been evaluated for maximum fuel economy keeping system cost very low and improving vehicle performance. With optimized gear ratios and reduced number of gears for parallel hybrid, it is possible to operate the engine in the best efficiency zones without downsizing. Motor is selected based on power to weight ratio, gradient requirements, improved acceleration performance and top speed requirement of vehicle in EV mode.

The goal of reducing fuel consumption and CO2-Emission is leading to turbo-charged combustion engines that deliver high torque at low speeds (down speeding). To meet NVH requirements damper technologies such as DMF (Dual Mass Flywheel) are established, leading to reduced space for the clutch system. Specific measures need to be considered if switching over from SMF (Single Mass Flywheel) to DMF [8]. Doing so has an impact on thermal behavior of the clutch system, for example due to reduced and different distribution of thermal masses and heat transfer to the surroundings. Taking these trends into account, clutch systems within vehicle powertrains are facing challenges to meet requirements e.g. clutch life, cost targets and space limitation. The clutch development process must also ensure delivery of a clutch system that meets requirements taking boundary conditions such as load cycles and driver behavior into account.

In this paper, design methodology of antiroll bar bush is discussed. Typical antiroll bar bushes have slide or slip mechanism, to facilitate the relative motion between ARB and bush. Inherently, this relative motion causes wear and noise of bush. To eliminate stated failure modes, the next generation bushes have been developed, which are using torsion properties instead of slip function. These bushes are already being used in various vehicles. This paper focuses on developing the simple mathematical model, design approach and optimization of ARB bushes. Also, comparison study is presented exploring, the differences and design criteria's between conventional and new generation anti-roll bar bushes.

In a current competitive automotive market, weight and cost optimization is the need of an hour. Therefore it is important to explore use of alternative material which has less weight, low manufacturing cost and better strength. This paper presents methodology to achieve cost & weight reduction through use of Austempered Ductile Iron (ADI) instead of alloy forging. ADI casting has lower density, physical properties at par with alloy forgings and lower manufacturing cost. Pivot arm is the one of the critical component of twin axle steering system which transfers the hydraulic torque from steering gearbox to second forward axle via linkage system. In order to design lightweight pivot arm, existing chromium alloy steel material is replaced with the Austempered ductile iron (ADI). Pivot arm is designed and validated digitally as well as bench test and results are found to be meeting cost and weight targets.

Unfavorable climates, fatigue, safety & deprived sleep of driver’s leads to use of AC system for their quick thermal comfort during night with engine ON. This scenario is very critical from a human’s safety & vehicle functionality point of view. This also consumes an additional 10-15% of fuel requirements in AC running conditions. So, to address the social problems of driver’s sleep and pollution-free environment by reducing the use of fossil fuels, there is a need for alternative techniques for air cooling which work during engine OFF condition. Various alternative options for air cooling have been reviewed. Accordingly, the packaging flexibility of phase change material (PCM) technology makes it easy to implement, yet effective usage of large quantity stored PCM, needs optimization. This paper proposes a design of a hybrid air conditioning system for sleeper commercial vehicles using a combined conventional compression and phase change material.