Search Results

The acoustical performance of a vehicle dash panel system is rated by the noise reduction, which is calculated from the sound transmission and absorption characteristics. A typical dash insulator consists of a steel panel (vehicle body panel), a porous decoupler and heavy layer in the form of sandwich construction. The use of dash panel is to block engine noise from entering into the interior cabin. In the present study the transmission loss of dash panel has been evaluated in reverberation chambers and the sound absorption of dash panel has been determined in impedance tube. This paper deals with improving over all sound transmission loss and shifting of the double wall resonance well below the engine firing frequencies by changing the decoupler materials such as felt and foams of different density and thickness and heavy layer mass per unit area.

In today’s automotive industry sound package material design and optimization is important considering the need for weight reduction and achieving targeted sound absorption and sound transmission loss values. As per traditional approach vehicle level noise reduction targets are defined considering flat samples, but in actual vehicle condition molded trimmed parts are used. This paper discusses about the systematic methodology developed for molded sample characterization in terms of BIOT’s properties. Effects of different parameters like area wise thickness variation, density variation on BIOT properties is studied. Comparison of BIOT’s properties of flat and molded dash sample is done to study the effect of molded structure. Using these BIOT’s properties prediction of sound absorption and sound transmission loss results carried out using FTMM approach for flat sample and SEA approach for molded sample.

Dual Phase (DP) steels with their high energy absorbing capacity are fast emerging as materials for automotive body applications with improved crashworthiness. The unique combination of high strength and good ductility associated with the DP steels originates from its specially developed microstructure that consists of martensitic islands in ferritic matrix. The high strength and good ductility are expected to give very good resistance to fatigue crack generation and propagation respectively. This paper discusses the fatigue properties determined for a DP steel grade viz. DP 800. The strain controlled fatigue tests were carried out on the un-notched specimens prepared from 1.2 mm sheets to generate E-N curves. The force controlled axial fatigue tests were carried out on two types of specimens prepared from 1.2 mm sheets to generate S-N curves for two Stress Concentration Factors (SCF) viz. 2.5 and 4.4.

In this work, the effect of tool rake angle and cutting speed on residual stresses of tool was studied, the rake angles of 0°, 5°, 10°, 15°, and 20° and a constant clearance (Relief angle) of 8° were used to turn bright mild steel on the lathe machine, A total of 15 experiments were carried out with three different cutting speeds (37.69, 59.37, 94.24 m/min) for each rake angle, keeping the feed rate and depth of cut constant. During the experimentation, the residual stresses were measured using an x-ray diffractiometer. This is all in order to explore the energy savings opportunities during regrinding of tools, useful production time and energy is being wasted due to regrinding or re-sharpening of tools when cutting tools got worn or blunt, selection of the rake angle which generate the optimum residual stresses in the tool, goes a long way in saving these time and energy.

Automobile industry is shifting towards lighter materials in order to meet the high strength to weight ratio as required for better performance, safety, and environmental concern. The objective of this review is to evaluate and compare the different advanced and light weight materials like advanced high strength steel (AHSS), Magnesium and Aluminium alloys, which will help in selection of appropriate materials for their intended application. In this paper comparison of materials on the basis of their current, applications, limitations, cost, potential future applications and percentage wise use in automotive vehicles are discussed. Solutions and suggestions are discussed to overcome the limitations of materials which will widen their future application. Case studies and charts for cost evaluation of different materials, on the basis of structural properties like stiffness and strength are also discussed.

Light weighting is significant in for automotive industry as it helps in less fuel consumption and to achieve better performance. Aluminium is a candidate material for light weighting. To design a component made of aluminium material, it is necessary to understand the fatigue performance of the material. In this paper, a study is carried out to understand the fatigue performance of aluminium 6xxx series alloys at an early stage of design without carrying out comprehensive fatigue testing. Coffin Manson Parameters are used to predict fatigue life. This research focusses on determining the gaps in existing models for aluminium alloys by carrying out comprehensive review of various models developed for 6xxx series which uses monotonic tensile data. Two models are developed and the predicted fatigue properties for this class of material are further compared with experimental fatigue, monotonic data and literature.

The effect of different cold- rolling and cryo-rolling routes on the strength and ductility of Al-6061 alloy was thoroughly investigated. Rolling decreased the grain size and increased the strength according to the Hall-Petch relationship. However subjecting the samples to ageing at different temperatures and for different time period increased the strength and improved the ductility. The ductility was improved due to the rearrangement and even decrease in dislocation density due to recovery and recrystallization during ageing while the strength was maintained due to ageing. Evolution of microstructure was investigated by optical microscopy, scanning electron microscopy. Preliminary hardness measurements coupled with tensile tests indicate the improvement of both yield strength and ductility. The disparity in ultimate tensile strength, yield strength and the elongation to failure with different ageing temperatures and for different time period is determined and discussed.

Accurate quantification of residual stresses is critical to predict expected fatigue life of the component. Quantification of residual stresses by X ray diffraction method offers substantial accuracy in results as compared to other methods of stress measurements. Depending on component processing and geometry, various stress measurement techniques are used to analyze stress patterns induced by these processing. This paper describes some of the stress measurement techniques by results obtained on two compressor valve (reed) samples which are undergone different processing. First reed sample is analyzed after blanking operation which is expected to give low compressive or tensile stresses whereas second reed sample is analyzed after tumbling operation which is done to get high compressive stresses.