Search Results

The utility of airplane flow-field measurements for wind-tunnel testing is reviewed. The methods and equipment developed at Boeing for these measurements are also described. The details of the latest system are presented along with typical results from recent wind-tunnel tests. Using the latest system, flow-field surveys of airplane configurations in industrial low-speed and transonic wind tunnels provide spatial distributions of lift and drag (profile and induced) with good repeatability. In addition, the probe speed and survey region is optimized so that typical full-wake surveys take 20-30 minutes to complete. Final data, displayed as total pressure, velocity vectors, vorticity contours, and distributions of lift and drag (profile and induced) are available approximately 10 minutes after survey completion.

Drilling fastener holes in large assemblies is traditionally accomplished through the use of large machine tools in order to obtain the accuracies required for the assembled part. Given recent advances of machine design and machine controller compensation, the accuracy of the motion platform can be corrected if the machine is repeatable. This coupled with the use of a vision system or touch probe to compensate for assembly variations, permit the use of smaller, more portable drilling systems. These smaller, more portable machine tools allow for lean manufacturing techniques to be incorporated into build processes, utilize less floor space, and in many cases are less costly than larger, permanent machine tools. This paper examines the feasibility of utilizing a small 5-axis, portable, drilling system for drilling the side panel skins on the F/A-18 E/F forward fuselage.

Assembly techniques for the majority of expendable and reusable launch vehicles have not changed much over the last thirty years. Some progress has been made, specifically on new programs, however, improvements on existing expendable launch vehicle production lines can be difficult to justify; even more so for one or two reusable vehicles. This presentation will focus on techniques and systems used for manual and automated assembly of expendable and reusable launch vehicle primary structures. Today's assembly is characterized by manual operations involving fixtures and templates, and all tasks are carried out primarily with single function hand tools. Typical assembly approaches used for metallic and composite primary structures will be discussed. Potential opportunities for process improvements utilizing advanced hand tools, mechanized and/or automated equipment will be addressed.

Fastener selection entails two functions, a staff function to select a group of fasteners for consideration and a design function to select the most suitable fastener for a specific function. This paper itemizes in detail the considerations that enter into each function in selecting fasteners for commercial and military aircraft, military unmanned vehicles, and space vehicles. Characteristics of specific bolts and fasteners are also tabulated.

A new process has been developed to cold work fastener holes on commercial aircraft flap tracks fabricated of 4340M steel. The process consists of pressing a high strength solid mandrel through a previously prepared hole in a defined manner. This process exhibits high tool life, low overall cost and eliminates the necessity for a final ream operation.

A review of the current extended-range twin-engine operations (ETOPS) and the modifications to the standards and processes that led to its successful operational record has contributed to the feasibility of developing an airplane and preparing an operator for ETOPS at entry into service. The airplane and engine manufacturers and component suppliers have continued to expand on these modified standards and processes in their design, build, test and support programs to meet regulatory authority ETOPS requirements and to facilitate the development of regulatory authority criteria for substantiating ETOPS capability prior to entry into service. Airlines, in conjunction with the manufacturers, have also developed improved processes that meet regulatory authority requirements for preparing an operator to integrate a new airplane into its existing ETOPS programs at entry into service.

There are a large number of space structures, orbital replacement units (ORUs) and other components that must be transported to orbit on a regular basis for the assembly and maintenance of the International Space Station (ISS). Some of this hardware will be ferried on the Spacelab Logistics Pallet (SLP), which has a long and reliable history of space flight successes. The carrier is well used, well qualified, and very adaptable for repeated use in accommodating cargoes of various sizes and shapes. This paper presents an overview of past, present and future hardware design solutions that accommodate EVA operations on the SLP. It further demonstrates how analysis techniques and design considerations have influenced the hardware development, EVA operations, and compliance with human engineering requirements for the SLP.

Two spindles are discussed in this paper. The first spindle was installed on nine C-frame riveters on the 737/757 wing line at the Boeing Renton facility. Due to discontinuing the use of Freon coolant and cutting fluid, the C-frame riveters had difficulty shaving 2034 ice box rivets with the existing 6000 RPM hydraulic spindles. The solution was to install electric 30,000 RPM shave spindles inside the existing 76.2 mm (3 in.) diameter hydraulic cylinder envelope. The new spindle is capable of 4 Nm (35 in. lbs.) of torque at full speed and 110 kgf (250 lbs.) of thrust. Another design of interest is the Electroimpact Model 09 spindle which is used for 20,000 RPM drilling and shaving on wing riveting systems. The Model 09 spindle is a complete servo-servo drilling system all mounted on a common baseplate. The entire spindle and feed assembly is only 6.5″ wide.

The Boeing Aero Grid and Paneling System (AGPS) is a programming language with built-in geometry features. Accessible through either a graphical user interface (GUI) or through a command line, AGPS can be used by operators with different levels of experience. Distributed with AGPS are approximately 300,000 lines of macros, or command files, which automate many engineering design and analysis tasks. Most command files were developed to produce inputs to engineering analysis codes such as A502 [1] and TRANAIR [2]. In many cases, command files have been grouped together in AGPS “packages,” which offer users simple menu pick and dialog options to automate entire engineering processes.

The Boeing F/A-18 E/F Program Wing Team, Lean Organization and Phantom Works have partnered to develop a “state of the art” lean production system for the Outer Wing that represents an evolutionary change in aircraft design and assembly methodology. This project is focused on improving quality, cycle and cost performance through the implementation of lean principles, technology integration and process improvements. This paper will discuss the approach taken to reach the end state objectives and the technologies and processes being developed to support it. Items to be discussed include lean principles and practices, new tooling concepts, improved part assembly techniques, advanced drilling systems, process flow enhancements and part handling/part delivery systems.

At The Boeing Company, the advent of a Determinant Assembly (DA) program and the subsequent production of accurate fuselage subpanels created a need to be able to position subpanels accurately and repeatably during fuselage assembly. The tool engineering organization of The Boeing Company and Advanced Integration Technology, Inc. (AIT) as the prime contractor, are developing and installing automated positioning and alignment systems throughout major 747 fuselage assembly areas which enable DA techniques. The benefits of this assembly approach and this automated precision tooling are flexibility, assembly accuracy, ease of assembly and associated speed, reduced downtime for tool maintenance, and improved shop-floor ergonomics.

The traditional method of determining the net thrust of an engine in cruise is explained. It is shown to result in a satisfactory net thrust uncertainty for jet and low bypass ratio engines but to be unsuitable for high bypass ratio engines. A redefinition of net thrust results in a new thrust determination method, called continuity method, which yields acceptable levels of net thrust uncertainty. The new method no longer requires supporting tests in a simulated altitude facility. The question is raised whether in future programs the demonstration of guaranteed cruise performance of an engine should not be carried out in flight tests rather than in an altitude test facility.

Three separate and distinct electrolytic and one galvanic process were identified by visual inspection, metallographic, electron microprobe, and x-ray diffraction analysis in a clocked, flip-flop integrated circuit flat pack and/or the associated printed circuit test jig (two on flat pack and two on circuit board). These four processes were all found to be detectable by the use of noise measurements in microvolts per root cycle at 1000 Hz (cycles per second). The direct current applied for noise measurement to the integrated circuit devices was 100 micro-amperes, as compared to the 6-8 milliamperes required for normal operation. After initial experimentation, the devices were caused to fail in a laboratory ambient environment, followed by an acceleration of the rate of electrolytic reaction through the use of essentially 100 percent relative humidity, versus the upper specification limit of 80 to 98% relative humidity.

Aircraft manufacturing in the 21st century sees a future much different to that seen one and two decades before. Manufacturers of both military and commercial aircraft are challenged to become Lean, Agile and Flexible. As progress is slowly made toward introducing advanced assembly systems into production, the overall cost of automation is now more closely scrutinized. After spending tens of millions of dollars on large automated systems with deep foundations, many manufacturers find themselves locked into high cost manufacturing systems that have specific, inflexible configurations. This kind of scenario has caused a shift in the attitude of airframe assemblers, to go back to basics. Lean manufacturing is seen as a way to build aircraft with very low investment in equipment and tools. Today's advanced systems developers do understand the need for more affordable assembly systems.

This paper presents a detailed overview of the advantages and benefits of using 2-D barcodes, called Data Matrix codes, on Wing Fastening System (WFS) Tooling. This project was conducted on, but not limited to, the 777 Wing Fastening System (GEMCOR) tooling including the drills, fingers, and button dies. This paper will show how using Data Matrix codes to identify tooling will: Eliminate excessive downtime due to the operator using the incorrect tooling for a given tool setup. Reduce the cost associated with panel rework due to the use of incorrect tooling. Reduce the cost associated with excessive tool inventory or last minute ordering to keep up with production needs. Track tool life information for each specific tool. Provide operators with an easy to use tool setup reference document. And provide the factory with the ability to trace panel damage or defects back to the specific machine and exact tooling used.

New manufacturing technologies such as high speed machining (HSM) are being developed to produce high quality aerospace components. While our developing understanding of machining dynamics is enabling precise control of cutting tools to provide for high dimensional accuracy, residual stresses present in aluminum mill products can compromise the ability to machine dimensionally accurate components from these stock materials. The advantages of precise tool control can be lost if the metal being cut moves during machining. And, even a perfectly machined part that distorts when it is released from the machine bed will cause problems upon assembly. Thus, ensuring the quality of the mill product becomes an enabling technology for advanced manufacturing approaches such as HSM.

Many mechanical systems employing fluid power use one or more valves to control fluid flow. Often these valves can be quite complex, with many inlets and exits, reversing flow, flow and pressure control, and other unique features. It is desirable to model these valves and the associated fluid and control logic circuits with software during the design phase, and explore the effect of design changes on system performance using simulation and other analyses without having to build and modify expensive prototypes. A number of commercially available software packages offer various methods for “graphically modeling” dynamic systems, and some, offer the user pre-defined libraries of hydraulic components that greatly speed the modeling process. However, the variations on valve design are unlimited, and it is often necessary to model a hydraulic valve that has not been previously defined. This paper describes an approach allowing essentially any valve configuration to be modeled.

A discussion of wing-nozzle configuration development for the application of upper surface blowing to a STOL airplane is presented. The technical challenge is to achieve an integrated system which provides the desired performance for the low speed design conditions and also results in efficient operation during cruise. The resulting configuration is a complete integration of the propulsion system and airplane aerodynamics to achieve efficient operation at all regimes. This paper examines the major design parameters to be considered, describes a number of the configurations tested, and presents static and wind tunnel test results for these configurations. Concluding remarks are made relative to USB nozzle development.

The process of developing a Payload Attach System (PAS) which will support a wide range of experimental and commercial payloads on the International Space Station (ISS) has experienced an interesting evolution during its design, development, test and evaluation (DDT&E) phase. This evolution has been caused in large measure by requirements intended to insure compatibility of the PAS with the extravehicular activity (EVA) crewmember during nominal and contingency operations in and around the PAS sites. As the design of the ISS transitioned from its Freedom predecessor, the effort to keep costs down by preserving as much of the original Freedom design as possible led to design decisions that challenged engineering thinking.

This paper discusses some of the problems of developing and maintaining equipment containing integrated circuits. The problems discussed fall into three categories: (1)Processing, (2) Fault Isolation, and (3) Human Error. Quantitative study of these problems shows the highest number were experienced during preliminary-manufacturing and testing (screening and burn-in), with a decrease during final manufacturing checkout (board assembly and final testing) and a minimum during the system operational period. The paper concludes that maintainability is still the necessity it was even with the advent of reliable integrated circuits. This is substantiated by the many failures and defects encountered during manufacturing and development phases. Manufacturing economics force the consideration of maintainability in integrated circuit design.