Search Results

This study involves two areas of research. The first is the finalization of the Pedestrian Crash Data Study (PCDS) in order to provide detailed information regarding the vehicle/pedestrian accident environment and how it has changed from the interim PCDS information. The pedestrian kinematics, injury contact sources, and injuries were analyzed relative to vehicle geometry. The second area presented is full-scale attempts at reconstruction of two selected PCDS cases using the Polar II pedestrian dummy to determine if the pre-crash motion of the pedestrian and vehicle could somehow be linked to the injuries and vehicle damage documented in the case.

A new technique for measuring the friction coefficient between the punch and workpiece during sheet forming operations has been developed at the Ohio State University. Various materials, such as interstitial-free (IF) steel, high strength (HS) steel, an aluminum alloy (2008T4) and 70/30 brass, were tested under dry and oil lubrication conditions at different punch rates and process conditions. The results show that punch friction depends on the angle of wrap, which varies with punch stroke, and on the strain rate, which depends on punch velocity. The O.S.U. Friction Test is described and typical results are presented which verify the usefulness of the new procedure.

The handling, stability, and rollover resistance of vehicles is presently being studied by both the automotive industry and the National Highway and Traffic Safety Administration (NHTSA). However, to study the handling and rollover behavior of each vehicle on the road is not feasible. The ability to categorize and compare the rollover and handling behavior of various vehicles is a subject of considerable research interest. This paper examines the possibility of characterizing vehicle classes through the use of a three degree-of-freedom linear model. Initially, segregation is studied by evaluating the eigenvalue location in the complex domain for vehicle sideslip velocity, yaw rate, and roll angle. Then the influence of numerator dynamics on vehicle behavior is studied and vehicle class segregation is attempted through evaluation of the amplitude ratio of the frequency responses for sideslip velocity, yaw rate, and roll angle.

Heat exchanger design correlations are usually obtained from experiments performed on prototype heat exchangers. The data consist of total or overall thermal resistances which are usually separated into individual thermal resistances by appropriate manipulation. This paper presents an experimental investigation of the factors that affect the accuracy of the individual thermal resistances obtained from overall heat exchanger measurements. All experiments were performed such that one thermal resistance was varied while the other thermal resistances were kept nearly constant. The analysis that followed consisted of determining both the fixed and variable thermal resistances, together with their uncertainties.

The advent of the Hybrid III crash test dummy marked the beginning of biofidelic anthropomorphic test devices. During the development of its critical components, notably the head, neck, knee, and thorax, biomechanical cadaver test results were incorporated into the design. The result was a dummy that represented the 50th percentile male during idealized impacts. In order to achieve a more biofidelic response from the components, many exotic materials and unique designs were utilized. The thorax, for instance, incorporates a spring steel rib design laminated with a viscoelastic polymeric composite material to damp the response. This combination results in the proper hysteretic losses necessary to model the human thorax under impact loading conditions. The disadvantage of this design is that the damping material properties are highly sensitive to temperature. A variation of more than 5 degrees Fahrenheit dramatically affects the response of the thorax.

This paper presents an overview of the evolution of computer simulations in vehicle collision and occupant kinematic reconstructions. The basic principles behind these simulations, the origin of these programs and the evolution of these programs from a basic analytical mathematical model to a sophisticated computer program are discussed. In addition, a brief computer development history is discussed to demonstrate how the evolution of computer assisted vehicle accident reconstruction becomes feasible for a reconstructionist. Possible future research in computer reconstruction is also discussed.

A newly developed process allows the near-net shape fabrication of alumina/aluminum composite bodies via the immersion of a sacrificial oxide preform into a molten aluminum alloy bath. The resulting composite possesses an attractive range of properties for application in several automotive components. These properties include: high strength and stiffness, appreciable thermal and electrical conductivity, high strength at elevated temperatures, coefficient of thermal expansion of 10 X 10-6 C-1 and relative ease of machinability. Low cost fabrication renders this material/process ideal for components such as brake rotors and calipers, cylinder bore liners, piston components.

Objectives. Examination of head injuries in the Pedestrian Crash Data Study (PCDS) indicates that many pedestrian head injuries are induced by a combination of head translation and rotation. The Simulated Injury Monitor (SIMon) is a computer algorithm that calculates both translational and rotational motion parameters relatable head injury. The objective of this study is to examine how effectively HIC and three SIMon correlates predict the presence of either their associated head injury or any serious head injury in pedestrian collisions. Methods. Ten reconstructions of actual pedestrian crashes documented by the PCDS were conducted using a combination of MADYMO simulations and experimental headform impacts. Linear accelerations of the head corresponding to a nine-accelerometer array were calculated within the MADYMO model's head simulation.

There have been a number of papers written about the dynamic effects of low speed front to rear impacts between motor vehicles during the last several years. This has been an important issue in the field of accident analysis and reconstruction because of the frequency with which the accidents occur and the costs of injuries allegedly associated with them. Several of these papers have discussed the importance of the coefficient of restitution in the accelerations and speed changes that the vehicles undergo in such impacts. These discussions often include data showing the measured restitution for impacts involving various bumper types and closing speeds. However, in most of these studies, the impacts are controlled so that direct bumper to bumper impacts occur. This paper will present the results of several rear impact tests with non-standard impact configurations.

This paper addresses the question if testing wing alone configurations has a place in the design process of an open wheel race car. Data from 40% models and stand alone full size wings are compared to determine if wing alone testing is a good predictor of performance when the wing is mounted on the car.

The aim of this paper is to document a three year process of product development of the Formula Lightningtm electric race car constructed at the Ohio State University. Today interest in electric vehicles (EV's) is growing, due to the technological advances in recent years, but also in part due to recent legislation which mandates the introduction of ‘zero emission vehicles’ in California before the end of the century. The definition of ‘zero emission vehicle’ is: a vehicle which does not emit any pollutants during operation. Technologically, the only near term vehicle which meets this definition is an EV. One of the most difficult problems of electric racing is that the usable energy in a given set of batteries is not as easily determined as the amount of fuel in a tank. Also, the motor controllers may limit power output as battery voltage drops, further decreasing the amount of usable energy in a battery set.

Postcrash fires are a frequent cause of death in otherwise survivable automobile and aircraft accidents. The idea of the ICED (Internal Circuit Emergency Disconnect) battery [1] is to eliminate electrically ignited postcrash fires by means of an inertial interrupt device that will disconnect the active circuit at the battery if an accident should happen. The design of the prototypes that were tested and the analysis of the disengagement performance will be discussed. A ballistic pendulum impact test rig was designed and used to test the prototypes. The test results and analytical values were shown to be satisfactorily close to each other.

The process of producing co-continuous ceramic composite material has been investigated in order to provide a greater understanding of the formation mechanism and hence evaluate the viability of commercial applications for these exciting new materials. The ease of manufacture for components combined with the low production cost hold great promise for the production of brake rotors, brake calipers, piston crowns, cylinder liners, gears and turbine compressors. Practical issues such as bonding to this material, together with the machinability have been addressed, our findings are presented in this paper.

For some vehicle dynamics applications, an estimate of a vehicle's center of gravity (cg) height and mass moments of inertia can suffice. For other applications, such as vehicle models and simulations used for vehicle development, these values should be as accurate as possible. This paper presents several topics related to inertial parameter estimation and measurement. The first is a simple but reliable method of estimating vehicle mass moment of inertia values from data such as the center of gravity height, roof height, track width, and other easily measurable values of any light road vehicle. The second is an error analysis showing the effect, during a simple static cg height test, of vehicle motion (relative to the support system) on the vehicle's calculated cg height. A method of accounting for this motion is presented. Similarly, the effects of vehicle motion are analyzed for subsequent mass moment of inertia tests.

In many manual transmissions, conditions for the onset of vibro-impacts from an unloaded gear pair are more likely than from an engaged set. Although some of the general characteristics of neutral gear rattle are known, no specific analytical models are available in the literature that can explain interactions between unloaded and loaded gear pairs in the drive rattle mode. For the sake of illustration, a particular problem for a light duty truck is studied in this paper and dynamic interactions are investigated. Some experimental measurements are first presented to define the unloaded gear rattle problem. Linear and non-linear mathematical models of the driveline are developed to understand, quantify and control the rattle problem. Trends predicted by simulations are compared with those observed in experiments. The effects of various gear run-ups and vibratory drag torques are investigated.

In sheet metal forming, drawbeads are often used to control uneven material flow which may cause defects such as wrinkles, fractures, surface distortion and springback. Appropriate setting and adjusting the drawbead force is one of the most important parameters in sheet forming process control. However, drawbead design and drawbead force adjustment still rely on trial-and-error procedures. This paper summarizes the guidelines in drawbead design, evaluates a number of mathematical models in estimating drawbead forces, and investigates the effects of sheet thickness, material properties, drawbead geometry and penetration on the drawbead force.

Predominant failure modes in the forming of sheet metal parts are wrinkling and tearing. Wrinkling may occur at the flange as well as in other areas of the drawn part and is generated by excessive compressive stresses that cause the sheet to buckle locally. Fracture occurs in a drawn material which is under excessive tensile stresses. For a given part and blank geometries, the major factors affecting the occurrence of defects in sheet metal parts are the blank holder force (BHF) and the blank holder pressure (BHP). These variables can be controlled to delay or completely eliminate wrinkling and fracture. Modern mechanical presses are equipped with hydraulic cushions and various advanced multi-point pressure control systems. Thus, the BHP can be adjusted over the periphery of the blank holder as a function of location and time (or press stroke).

Shrink flanging is a major sheet forming operation to produce convex flanges in structural sheet metal components. Flanges are used for appearance, rigidity, hidden joints, and strengthening of the edge of sheet parts such as automobile front fender and complex panels formed by stretch/draw forming. Wrinkling around the flange edge is the major defect in shrink flanging operation. There has been a lack of reliable mathematical modeling to predict the strains and wrinkles in shrink flanging operations. A trial-and-error approach has been usually practiced in tooling and process designs. In this paper, a wrinkling criterion in shrink flange is proposed based on a simplification from a general criterion for a doubly curved anisotropic shell. The mathematical model for strain analysis in shrink flanging is established based on Wang and Wenner's strain model for stretch flange. Shrink flanging experiments were conducted to validate the theories.

This paper describes the background and development of a program focused on motorsports engineering education currently in progress at the Ohio State University (OSU). An interdisciplinary curriculum, with the involvement of various engineering departments, is being proposed for development in an attempt to address some of the engineering education needs of the motorsports industry. The program described in this paper strives to provide engineering students with an interdisciplinary background race engineering, and also provides opportunities for motorsports oriented thesis projects. The paper briefly summarizes the key elements of the curriculum, and describes how the integration of course material from different disciplines with team work on student competition projects, possibly coupled with internships with racing teams, can provide an ideal setting for the education of a new generation of race engineers.

Liver trauma research suggests that rapidly increasing internal pressure plays a role in liver injury. Previous work has shown a correlation between pressure and liver injury in pressurized ex vivo human livers when subjected to blunt impacts. The purpose of this study was to extend the investigation of this relationship between pressure and liver injury by testing full-body post-mortem human surrogates (PMHS). Pressure-related variables were compared with one another and also to previously proposed biomechanical predictors of abdominal injury. Ten PMHS were tested. The abdominal vessels were pressurized to physiological levels using saline, and a pneumatic ram impacted the right side of the specimen ribcage at a nominal velocity of 7.0 m/s. Specimens were subjected to either lateral (n = 5) or oblique (n = 5) impacts, and the impact-induced pressures were measured by transducers inserted into the hepatic veins and inferior vena cava.