Search Results

Environmentally friendly fuels and lubricants research on hydraulic fluids, engine oils, greases and industrial applications is of interest to government agencies and manufacturers of equipment, engines and vehicles. The key to increasing the use of renewable natural resources is developing fluids of equivalent performance to petroleum base products, at an acceptable product cost. The well known drawbacks of vegetable oils are oxidation stability and low temperature properties. This study compares commercial fluids and laboratory formulations as to their rheological properties and uses different approaches to solve both the low temperature and the oxidative stability problems. Frictions and wear characteristics of the fluids are evaluated and several fluids are compared laboratory bench tests.

Biodiesel fuels are widely known to yield an increase in NOx emissions in many diesel engines. It has been suggested that the increase in NOx is due to injection timing differences caused by the low compressibility of biodiesel. In this work, comparisons of injection timing and duration were performed for diesel fuel and a range of biodiesel blends (B20 to B100). The fuel injector on a 4-stroke, single-cylinder, four horsepower, air-cooled, direct injection diesel engine was positioned in a spray chamber while the engine was motored and fuel was delivered to the injector by the fuel pump on the engine. Spray visualization and quantification of injection timing were performed in the spray chamber using an engine videoscope, light attenuation from a HeNe laser and fuel line pressure, and were synchronized to crank shaft position.

In this paper a model of a three-phase inverter drive will be presented that is suitable for inclusion in a DC distribution system analysis. It will be shown that the drive can be accurately modeled on the electrical side by a capacitor, representing the bus capacitance of the inverter, in parallel with a current source. The current source consists of a DC component, corresponding to net power flow to and from the flywheel, plus high-frequency current harmonics generated by the operation of the switch-mode inverter. Closed-form expressions for the current harmonics can be derived by analyzing the AC currents in the electric machine and the switch-mode nature of the inverter, including the “dead-time” effect, and will be presented in the paper. Comparisons between edge-based and center-based pulse-width operation suggest that center-based PWM produces less harmonic content. It is shown that “dead-time” can have a significant effect on the harmonic content.

Several oxygenates have been proposed and tested for use with diesel fuel as a means of reducing exhaust emissions. This paper examines dimethyl ether (DME), which can be produced in many ways including via Air Products and Chemicals, Inc's Liquid Phase Technology (LPDME ™). Modest additions of DME into diesel fuel (2 wt.% oxygen) showed reductions in particulate matter emissions, but the previous data reported by the author from a multicylinder Navistar 7.3L Turbodiesel engine were scattered. In this study, experiments were performed on a multi-cylinder Navistar 7.3L Turbodiesel engine to repeatably confirm and extend the observations from the earlier studies. This is an important step in not only showing that the fuel does perform well in an engine with minor modifications to the fuel system, but also showing that DME can give consistent, significant results in lowering emissions.

THE effects of introducing a portion of the fuel charge of a diesel engine into the intake manifold in the form of a fine mist are reported in this paper. Laboratory tests with swirl-chamber and open-chamber engines resulted in smoke reduction up to 80%, increase in smoke-limited power output up to 18.5%, decrease in specific fuel consumption up to 9.8%, shorter ignition lag, lower maximum rate of pressure rise, and smoother operation. In running on good-grade diesel fuel approximately 15% of the main fuel proved to be as good a manifold fuel as any. It was also found that a diesel engine could operate satisfactorily on substandard fuels down to zero cetane number when fumigation was employed. Maximum benefits from fumigation accrued when inducting fuel in the form of a very fine mist (not over 4 microns) produced by Micro-Fog. As yet an economical method of producing this finely atomized fuel spray in large quantities has not been found.

In this study, the performance and emissions of a 4 cylinder 2.5L light-duty diesel engine with methane fumigation in the intake air manifold is studied to simulate a dual fuel conversion kit. Because the engine control unit is optimized to work with only the diesel injection into the cylinder, the addition of methane to the intake disrupts this optimization. The energy from the diesel fuel is replaced with that from the methane by holding the engine load and speed constant as methane is added to the intake air. The pilot injection is fixed and the main injection is varied in increments over 12 crank angle degrees at these conditions to determine the timing that reduces each of the emissions while maintaining combustion performance as measured by the brake thermal efficiency. It is shown that with higher substitution the unburned hydrocarbon (UHC) emissions can increase by up to twenty times. The NOx emissions decrease for all engine conditions, up to 53%.

Two widely available engine and hybrid electric vehicle (HEV) simulation packages have been integrated to reduce fuel consumption and pollutant emissions for a hybrid electric sport utility vehicle. WAVE, a one-dimensional engine analysis tool available from Ricardo Software, was used to model a 2.5L 103 kW Detroit Diesel engine. This model was validated against engine performance and emissions data obtained from testing in a combustion laboratory. ADVISOR, an HEV simulation software developed by the National Renewable Energy Laboratory in partnership with the Department of Energy (DOE), was used to model a 2002 Ford Explorer that is being converted into an HEV by the Penn State University FutureTruck team. By integrating the output file from WAVE as the input engine data file for ADVISOR, one can predict the effect of changes in engine parameters on vehicle emissions, fuel consumption, and power requirements for specified drive cycles.

Polymer Electrolyte Membrane Fuel Cell (PEMFC) is regarded as a potential alternative clean energy source for automobile applications. Key challenges to the acceptance of PEMFC for automobiles are the cost reduction, improvement in power density for its compactness, and cold-start capability. High current density operation is a promising solution for them. However, high current density operation under normal and sub-zero temperature requires more oxygen flux for the electrochemical reaction in the catalyst layer, and it causes more heat and water flux, resulting in the significant voltage losses. So, the theoretical investigation is very helpful for the fundamental understanding of complex transport phenomena in high current density operation under normal and sub-zero temperature. In this study, the numerical model was established to elucidate the impacts of mass transport phenomena on the cell performance through the numerical validation with experimental and visualization results.

In this paper, a completely non-intrusive method of monitoring driver drowsiness is described. Because of their abilities to learn behavior and represent very complex relationships, artificial neural networks are the basis of the method presented. Four artificial neural networks are designed based on the hypothesis that the time derivative of force (jerk) exerted by the driver at the steering wheel and accelerator pedal can be used to discern levels of alertness. The artificial neural networks are trained to replicate non-drowsy input, and then tested with unseen data. Data sets that are similar to the training sets will pass through the network with little change, and sets that are different will be changed considerably by the network. Thus, the further the driver's jerk profile deviates from the non-drowsy jerk profile, the greater the error between the input and output of the network will be.

Designing for human variability (DfHV) requires efficient allocation of sizing and adjustability. This can preserve product performance while reducing some measures of cost. For example, specifying only as much adjustability as necessary for a desired level of accommodation leads to devices which are better suited to their users and more cost efficient. Similarly, when multiple sizes of an adjustable artifact are to be produced, specifying only as many sizes as are necessary, with an appropriate amount of adjustability per size, leads to a set of products that cost less, require fewer unique parts, facilitate maintenance standardization, and ease inventory control. An alternative to the standard procedure of evenly dividing size ranges is considered wherein an equal degree of accommodation per size is also presented. A simple example related to exercise bicycle seat height is discussed.

THIS PAPER reports progress in a current research program on the use of secondary fuels as ignition promoters, to aid cold-weather starting of diesel engines. The best method, the authors report, is to supply ether to the intake manifold in vapor form. The amount of ether reaching the manifold can be controlled easily, and any condensed vapor is carried along by the cold intake air. Thus, the difficulties resulting from ether accumulation are prevented. There is a minimum starting temperature for each engine type, even with the vapor introduction of ether. Therefore, further work is needed to assure cold starting in all engines.

Two of the goals of the Penn State FutureTruck project were to reduce the emissions of the hybrid electric Ford Explorer to ULEV or lower, and improve the fuel economy by 25% over the stock vehicle. The hybrid electric vehicle system is powered with a 103kW 2.5L Detroit Diesel engine which operates with a fuel blend consisting of ultra-low-sulfur diesel and biodiesel (35%). Lower emissions are inherently achieved by the use of biodiesel. Additionally, the engine was fitted with a series of aftertreatment devices in an effort to achieve the low emissions standards. Vehicle testing has shown a gasoline-equivalent fuel economy improvement of approximately 22%, a reduction in greenhouse gas emissions by approximately 38%, and meeting or exceeding stock emissions numbers in all other categories through the use of an advanced catalyst and control strategy.

In this study, performance and emissions characteristics of an LPG direct injection (DI) engine with a rotary distributor pump were examined by using cetane enhanced LPG fuel developed for diesel engines. Results showed that stable engine operation was possible for a wide range of engine loads. Also, engine output power with cetane enhanced LPG was comparable to diesel fuel operation. Exhaust emissions measurements showed NOx and smoke could be reduced with the cetane enhanced LPG fuel. Experimental model vehicle with an in-line plunger pump has received its license plate in June 2000 and started high-speed tests on a test course. It has already been operated more than 15,000 km without any major failure. Another, experimental model vehicle with a rotary distributor pump was developed and received its license plate to operate on public roads.

A study has been experimentally conducted in an optically-accessible DI Diesel engine operating on 50/50 mixture of iso-octane and tetradecane to evaluate a planar laser light scattering technique for the in-cylinder study of soot. Two simultaneous images, taken with vertically and horizontally polarized scattered light, were used to determine the polarization ratio, CHH/CW. This magnitude of the polarization ratio was employed to distinguish soot particles from fuel droplets. The spatial and temporal variations of soot during the combustion cycle were investigated with images taken at various crank angles and swirl levels at three different planes in the combustion bowl. For the high swirl case, soot was uniformly distributed in the combustion bowl. For the non-swirl case, however, soot was mainly observed near the wall and at the top plane, and was observed to exist later into the expansion stroke.

Several synthetic fuels derived from shale and coal were evaluated with respect to a reference petroleum-based Diesel fuel. Tests conducted using a single-cylinder DI Diesel engine were designed to quantitatively compare the fuels on the basis of performance, combustion characteristics, gas-phase emissions, particulate emissions, and biological activity of the solid phase soluble organic fraction. The biological activity was assessed using the Ames Salmonella typhimurium test. The shale fuels studied were a Paraho marine Diesel fuel and a light shale oil condensate from the Logan Wash in situ retorting operation. The coal liquids, Solvent Refined Coal-II and Exxon Donor Solvent, could not be run neat; therefore, they were blended 20% and 40% by volume with the certified DF-2 baseline fuel. Of the synthetic fuels tested, only the Paraho marine Diesel fuel exhibited the qualities of a good finished Diesel fuel.

Standing reach envelopes are important tools for the design of industrial and vehicle environments. Previous work in this area has focussed on manikin-based (where a few manikins are used to simulate individuals reaching within the region of interest) and population-based (where data are gathered on many individuals reaching in a constrained environment) approaches. Each of these methods has merits and shortfalls. The current work bridges the manikin- and population-based approaches to assessing reach by creating population models using kinematic simulation techniques driven by anthropometric data. The approach takes into account body dimensions, balance, and postural cost to create continuous models that can be used to assess designs with respect to both maximal and submaximal reaches. Cost is quantified as the degree to which the torso is involved in the reach, since the inclination of the torso is a good measure of lower-back load and may be related to subjective reach difficulty.

The ignition of single fuel droplets in air is modeled according to the time-varying conditions within the droplet and the boundary layer around the droplet. Ignition is hypothesized when some point in the boundary layer has experienced a sufficiently severe history in terms of pressure, temperature, equivalence ratio, and time to auto ignite. Experiments were conducted with a wide variety of fuels to validate the model. A critical size concept for ignition was predicted by the model and substantiated by the experiments.

This study shows conclusively that some of the direct microbial mutagenic activity of the soluble-organie-fraction from Diesel particulate matter can be attributed to 1-nitropyrene. 1-nitropyrene has been shown to be formed by the nitration of pyrene, and pyrene is one inherent product of the diffusion-controlled-combustion of hycrocarbons that occurs with Diesel engine operation. Nitrogen dioxide, in the presence of water vapor, is shown to be a potential nitrating agent, and this gas can be produced by the high temperature oxidation of the nitrogen contained in the oxidant. These results are based on studies which used a well-documented engine, model fuel, model oxidants, and synthetic lubricant.

This paper investigates experimental uncertainties associated with gaseous and particulate emissions measurements in a partial flow emissions sampling system developed and built at the Larson Transportation Institute of the Pennsylvania State University. A small fraction of the tail pipe exhaust is diluted with dilution air and passed through a cyclone to eliminate particles bigger than 2.5 microns. The diluted exhaust is then passed through a 47 mm Teflon filter for gravimetric measurement of Particulate Matter (PM). Mass flow controllers operating at 5Hz are used to control the flow rates of dilution air, diluted exhaust, and proportional flow of diluted exhaust into a Tedlar bag. An ultrasonic flow meter is used to measure flow rate of tail pipe exhaust. At the end of a test, the concentration of gaseous emissions in the bag, namely CO2, CO, HC, and NOx are measured using a bag emissions analyzer.

Thermal barrier coated diesel engines, also known as low heat rejection (LHR) engines, have offered the promise of reducing heat rejection to the engine coolant and thereby increasing overall thermal efficiency. However, the larger market potential for thermal barrier coated engines may be in retrofitting in-service diesel engines to reduce particulate emissions. Prior work by the authors has demonstrated a significant decrease in particulate emissions from a thermal barrier coated, single-cylinder, indirect injection (IDI) diesel engine, primarily through reduction of the volatile (VOF) and soluble (SOF) fraction of the particulate. This prior work relied on conventional, commercially available, petroleum-based lubricants. The present study concerns the additional benefits for particulate reduction provided by vegetable oil lubricants. These lubricants are derived from renewable resource materials and can provide a reduction in lubricant generated particulate matter.