Search Results

Based on 3- dimensional velocity data at intake valve exit area of typical SI engine intake ports (horizontal and sloping directed ports) measured by hot wire anemometry in a steady flow rig, the magnitudes and compositions of inflow angular momentum flux and swirl ratios at the end of induction process generated by each velocity component were computed at different intake valve lifts and distances along valve axis. A microscopic evaluation method was provided for evaluating intake port characteristics according to intake valve exit flow field.

The magnitudes and compositions of in-cylinder tumble ratio generated by each velocity components were computed at different intake valve lifts and distances along the direction of valve axis in this paper, based on the three-dimensional velocity data measured by hot-wire anemometry at intake valve periphery of typical SI engine intake ports (horizontal and sloping directed ports) in a steady flow rig. The effect of velocity profiles at above two intake ports exit on in-cylinder tumble generation was studied, and a microscopic analytical method of evaluating tumble-generating capability of intake ports was developed according to the velocity profiles at intake valve exit area.

The velocity and turbulence intensity profiles at exit of intake valve from typical SI engine intake ports (horizontal and sloping directed ports) were measured by hot wire anemometry (HWA) in a steady flow rig. The characteristics of velocity and turbulence intensity distribution under different valve lifts and at distances along valve axis were analysed and compared between above two intake ports. Results showed that velocity and turbulence intensity profiles are strongly dependent on intake port form,valve lift and surrounding geometry,they vary not only around valve head periphery but also along valve axis.

The purpose of this study was to gain a better understanding of the effects of port fuel injection strategies and thermal stratification on the HCCI combustion processes. Experiments were conducted in a single-cylinder HCCI engine modified with windows in the combustion chamber for optical access. Two-dimensional images of the chemiluminescence were captured using an intensified CCD camera in order to understand the spatial distribution of the combustion. N-heptane was used as the test fuel. The experimental data consisting of the in-cylinder pressure, heat release rate, chemiluminescence images all indicate that the different port fuel injection strategies result in different charge distributions in the combustion chamber, and thus affect the auto-ignition timing, chemiluminescence intensity, and combustion processes. Under higher intake temperature conditions, the injection strategies have less effect on the combustion processes due to improved mixing.

Biobutanol, i.e. n-butanol, as a second generation bio-derived alternative fuel of internal combustion engines, can facilitate the energy diversification in transportation and reduce carbon dioxide (CO2) emissions from engines and vehicles. However, the majority of research was conducted on spark-ignition engines fuelled with n-butanol and its blend with gasoline. A few investigations were focused on the combustion and exhaust emission characteristics of homogeneous charge compression ignition (HCCI) engines fuelled with n-butanol-gasoline blends. In this study, experiments were conducted in a single cylinder four stroke port fuel injection HCCI engine with fully variable valve lift and timing mechanisms on both the intake and exhaust valves. HCCI combustion was achieved by employing the negative valve overlap (NVO) strategy while being fueled with gasoline (Bu0), n-butanol (Bu100) and their blends containing 30% n-butanol by volume (Bu30).

The goal of this research was to study and quantify the effect of exhaust valve timing and residual gas dilution on in-cylinder flow patterns, flame propagation and heat release characteristics in a spark ignition engine. Experiments were carried out in a recently developed single cylinder optical engine. Particle image velocimetry (PIV) was applied to measuring and evaluating the in-cylinder flow field. Detailed analysis of flame images combined with heat release data was presented for several engine operating conditions, giving insight into the combustion process in terms of visible flame area and flame expansion speed. Results from PIV measurement indicates that the limited alteration of the in-cylinder bulk flow could be observed with the variation of exhaust valve timing. The in-cylinder fluctuating kinetic energies and their Coefficient of Variations (COVs) decrease with the advance of the exhaust valve timing.

Chemical reaction kinetics plays an important role in homogeneous charge compression ignition (HCCI) combustion. In order to control the combustion process, the underlying mechanism of auto-ignition must be explored, especially for the HCCI combustion using negative valve overlap (NVO) strategy, in which the residual gas affects the auto-ignition of next cycle remarkably. In this research, experimental research was carried out in a single cylinder gasoline engine equipped with an in-cylinder sampling system which mainly consists of a special spark plug, a sampling tube and a high-speed electromagnetic valve. In-cylinder charge was sampled at compression stroke and analyzed by FTIR with two types of fuel injection strategy, such as port fuel injection (PFI) solely and port fuel injection combined with injection during negative valve overlap (PFI & NVO-Injection).

Homogeneous charge compression ignition (HCCI) technology is promising to reduce engine exhaust emissions and fuel consumption in gasoline engine. However, it is still confronted with the problem of its limited operation range. High load is limited by the tradeoff between the quantity of working charge and dilution charge. Low load is limited by the high residual gas fraction and low temperature in the cylinder. One of the highlights of HCCI combustion research at present is to expand the low load limit of HCCI combustion by developing HCCI idle operation. The main obstacle in developing HCCI idle combustion is too high residual gas fraction and low temperature to misfire in cylinder. This paper relates to a method for achieving the appropriate environment for auto-ignition at idle and the optimal tradeoff between the combustion stability and fuel consumption by employing EIVO valve strategy with an equivalent air-fuel ratio.

In the paper, the experiment of a spark ignition engine fueled with dissociated methanol gas (D.M.) and gasoline dual fuels is conducted. A quasi-dimensional two-zone combustion model is developed to analyze the combustion process. Engine dynamometer test results demonstrate that the engine fueled with D.M. and gasoline dual fuels can be operated at leaner mixtures. The combustion duration and ignition delay are shortened. The maximum mass burning rate of the mixture increased by 36%. And maximum 17% improvement in thermal efficiency, and low carbon monoxide CO and hydrocarbon HC emissions are obtained. Continuous 500 cycle measurement of the combustion pressure history demonstrates that the cycle-to-cycle fluctuation of the combustion pressure is decreased considerably.

Natural gas is regarded as one of the most potential alternative fuels of engines because of its fruitful storage, good obtainable resources, and high octane value, etc. Compared with port fuel injection (PFI), Gasoline direct injection (GDI) has many advantages on volumetric efficiency improvement, lean-burning, emissions control, etc. A set of measuring and data acquisition system on CNG direct injection spark-ignited engines and the CNG multi-direct injection system are developed in this paper. Based on different injection modes of CNG single DI and compound DI (main injection and auxiliary-Injection), the investigations on combustion process of CNG DI engines has been conducted by the factors of in-cylinder mixture formation, air/fuel ratio, and injection timing, etc. Meanwhile, the three-dimension simulation on mixture formation and combustion principle of low-pressure CNG compound direct injection engines has also been researched.

Droplet velocities in a diesel fuel spray before and after impinging on a wall as well as air movement around the spray are measured at room temperature and pressure. The range of fuel injection pressure is from 101 MPa to 139 MPa. The diagnostic equipment is a Laser Doppler Velocimetry with Burst Spectrum Analyzer (LDV-BSA).The results show that the droplet velocities of such a high pressure diesel fuel spray spread in a wide range (about 0-250m/s), so it is necessary to use the ensemble average for describing the velocity variation with time and space. After injection, the velocity reaches its peak value rapidly then attenuates gradually. When the spray impinges on the wall, the average velocity of the rebounded droplets is obviously reduced and the rebounded angle of most droplets is smaller than 30 degree when the incident angle is 70 degree. In the near field zone, the air entrainment in spray jet appears to be lower than that in gaseous one.

Using a Laser Doppler Velocimetry with Burst Spectrum Analyzer (LDV-BSA), droplet velocities of a diesel fuel spray under a pressure higher than 100 MPa were measured at different points within the spray profile. Results show that although the mean velocity distribution at the sampling plane is rather uniform, the number-based droplet velocity distributions of two sampling points at the same plane are different. The conclusions agree with theoretical predictions through maximum entropy principle qualitatively.

A numerical simulation was performed to investigate the pilot ignited natural gas combustion process in a direct injection natural gas engine. Various mixture distribution characteristics were compared in terms of the evolution of mixture equivalent ratio distributions and mixture concentration stratifications around top dead center (TDC). Based on above, the pilot injections were specially designed to investigate ignition core formation and its effects on natural gas combustion process. The result shows that pilot ignition sites have great impacts on pilot fuel ignition process and natural gas combustion process. The pilot ignition site on the region with rich NG/Air mixture is disadvantageous to the pilot fuel ignition due to a lack of oxygen, which is not beneficial to ignition core formation.

Reactivity Controlled Compression Ignition (RCCI) has been shown to be an attractive concept to achieve clean and high efficiency combustion. RCCI can be realized by applying two fuels with different reactivities, e.g., diesel and gasoline. This motivates the idea of using a single low reactivity fuel and direct injection (DI) of the same fuel blended with a small amount of cetane improver to achieve RCCI combustion. In the current study, numerical investigation was conducted to simulate RCCI and HCCI combustion and emissions with various fuels, including gasoline/diesel, iso-butanol/diesel and iso-butanol/iso-butanol+di-tert-butyl peroxide (DTBP) cetane improver. A reduced Primary Reference Fuel (PRF)-iso-butanol-DTBP mechanism was formulated and coupled with the KIVA computational fluid dynamic (CFD) code to predict the combustion and emissions of these fuels under different operating conditions in a heavy duty diesel engine.

SI-CAI hybrid combustion, also known as spark-assisted compression ignition (SACI), is a promising concept to extend the operating range of CAI (Controlled Auto-Ignition) and achieve the smooth transition between spark ignition (SI) and CAI in the gasoline engine. In order to stabilize the hybrid combustion process, the port fuel injection (PFI) combined with gasoline direct injection (GDI) strategy is proposed in this study to form the in-cylinder fuel stratification to enhance the early flame propagation process and control the auto-ignition combustion process. The effect of bowl piston shapes and fuel injection strategies on the fuel stratification characteristics is investigated in detail using three-dimensional computational fluid dynamics (3-D CFD) simulations. Three bowl piston shapes with different bowl diameters and depths were designed and analyzed as well as the original flat piston in a single cylinder PFI/GDI gasoline engine.

The spark ignition-controlled auto-ignition (SI-CAI) hybrid combustion is promising in achieving smooth transition between SI and CAI combustion but, it is limited by the combustion cyclic-variation at late combustion phasing to avoid too high pressure rise rate (PRR). In this paper, to stabilize the combustion and reduce PRR, the in-cylinder fuel-stratification strategy is investigated in a gasoline engine, equipped with port fuel injection combined with single pulse direct injection (PFI-DI). Experimental results confirm the benefits of employing PFI-DI in comparison with PFI and single-pulse DI strategy. The influence of DI timing (Start of injection, SOI) on the combustion process is found to be quite complicated, in terms of combustion phasing, combustion stability, PRR and thermal efficiency. It makes the optimal-SOI calibration time-intensive, since complex trade-off between PRR and thermal efficiency is needed.

A pressure accumulative injection rate controllable unit injector-PAIRCUI is proposed and developed. This unit injector is powered by fuel pressure accumulation controlled by an electronic control unit and its injection rate is shaped by inner valves of the injector. Inherent advantages of an accumulator type unit injector have been carried out in this new design, including sructural simplicity, totally flexible injection timing, medium common rail pressure, tolerable pump size and flow requirement. A number of decisive features have also been realized that are significant for high efficiency and low emissions of engine combustion, including higher mean effective injection pressure(MEIP), pilot injection capability and rapid end of injection. The injection pressure is independent of engine speed, but regulated upon engine load. These characteristics are beneficial in improving engine performance and fuel consumption.

A great deal of effort has been directed towards Gasoline HCCI engines, which have the potential of providing better fuel economy and emission characteristics than conventional SI engines. For stable HCCI engine operation, cycle-by-cycle based closed-loop control is needed. Such a control scheme requires an accurate and reliable sensor to monitor the combustion and provide a feedback signal. At present, the general method used to measure the combustion parameters is to monitor in-cylinder pressure with a cylinder pressure sensor. However, using in-cylinder pressure transducers is not feasible for use in mass production of HCCI engines. A good substitute to get information about combustion is the knock sensor, which is already equipped on engines on a large scale. In this paper, the knock signal from an HCCI engine equipped with 4VVAS is analyzed in detail to find the relationship between the combustion parameters and the knock sensor signal.

A versatile liquid dosing device along with its metering theory, which can be applied to both SCR dosing system and DPF regeneration system of IC engine after-treatment system, is presented in this paper. The device is composed of a solenoid driven plunger pump, a nozzle and a pressure tube, and is pump-end controlled by PWM signals. Both electrically resistive and conductive liquids including DEF for SCR system, fuel for DPF regeneration, and gasoline for spark ignition engine, can be dispensed quantitatively with this device. A metering theory determining the liquid discharged per injection is developed by studying the system using a physical-mathematical model. The study shows that the liquid discharge can be well correlated with a measurable variable T3, which is associated with the net output energy. Experimental investigations verified that the metering results were independent of the state changes.