Search Results

The utilization of the SLAM (Simultaneous Localization and Mapping) technique was extended from the robotics to the autonomous vehicles for achieving the positioning. However, SLAM cannot obtain the global position of the vehicle but a relative one to the start. For sake of this, a fast and accurate system was proposed to obtain both the local position and the global position of vehicles based on mono-SLAM which realized the SLAM by using monocular camera with a lower cost and power consumption. Firstly, the rough latitude and longitude of current position was obtained by using common GPS without differential signal. Then, the Mono-SLAM operated on the consecutive video frames to generate the localization and local trajectory and its accuracy was further improved by utilizing the IMU information. After that, a piece of Map centered in the rough position obtained by common GPS was downloaded from the Open Street Map.

In order to reduce high-frequency harmonic noise produced by the blower in the auxiliary system of a fuel cell vehicle (FCV), a narrowband active noise control (ANC) method instead of conventional passive mufflers is adopted since the blower demands clean air condition and expects good acoustic performance. However, in ANC practical applications, the frequency difference between reference signal and actual primary signal, i.e., frequency mismatch (FM), can significantly degrade the high-frequency performance of narrowband ANC system. In this paper, a new narrowband ANC system is proposed to compensate for the performance degeneration due to the existence of FM and improve noise reduction at high frequencies. The proposed system consists of two parts: the Filtered Error Least Mean Square (FELMS) algorithm filtering the primary signals at wide frequency range other than those at the targeted frequencies, and the FM removal algorithm proposed by Yegui Xiao.

Gasoline Direct Injection (GDI) engines have attracted interest as automotive power-plants because of their potential advantages in down-sizing, fuel efficiency and in emissions reduction. However, GDI engines suffer from elevated unburned hydrocarbon (HC) emissions during start up process, which are sometimes worsened by misfires and partial burns. Moreover, as the engine is cranked to idle speed quickly in HEVs (Hybrid Electric Vehicle), the transients of quick starts are more dramatically than that in traditional vehicle, which challenge the optimization of combustion and emissions. In this study, test bench had been set up to investigate the GDI engine performances for ISG (Integrated Starter and Generator) HEVs during start up process. Based on the test system, cycle-controlled of the fuel injection mass, fuel injection timing and ignition timing can be obtained, as well as the cycle-resolved measurement of the HC concentrations and NO emissions.

Many studies show that under diesel engine operating conditions, SCR reductant sprays will impinge on the wall of exhaust pipes. In order to understand this impinging process of SCR reductant spray, and to analyze what factors affect it, a test bench was set up by means of high speed video camera. At atmospheric pressure, SCR spray was injected on a heated metal wall, the impacts of wall temperature, injection pressure, injection height and angle on developing characteristics of SCR reductant spray after impinging on the heated wall have been researched and analyzed. The results show that the heated wall temperature has a great impact on the spray developing process, when wall temperature is lower than 405K, after water evaporated the crystallized urea will remain on the wall to block exhaust pipes. When wall temperature is higher, the atomization and evaporation of SCR reductant spray will be better, and the hydrolysis process of urea will be faster.

Even though air compressors for traditional vehicles and fuel cell vehicles (FCVs) share many similarities, a fuel cell vehicle cannot directly employ the effective and mass-produced traditional vehicles' air compressors. This is because the fuel cell vehicles have special requirements, such as oil free, low flow rate with high pressure ratio, high efficiency, and low weight and volume. In order to find suitable air compressors to match the fuel cell system (FCS)'s requirements, different air compressors' performance and physical characteristics are compared. These air compressors include screw compressor with expander, roots compressor with expander, turbocompressor, and scroll compressor with expander. The comparison and analysis is both theoretical and practical. Results show that the turbocompressor and the roots compressor/expander have higher performance compared to the others in the aspects of input power, system efficiency, weight, and volume.

With introductions of stringent diesel engine emission regulations, the DOC and DPF systems have become the mainstream technology to eliminate soot particles through diesel combustion under various operation conditions. Urea-based SCR has been the mainstream technical direction to reduce NOx emissions. For both technologies, low-temperature conditions or cold start conditions pose challenges to activate DOC or SCR emission-reduction performance. To address this issue, mini or full flow burner systems may be used to increase exhaust temperature to reach DOC light-off or SCR initiation temperature by combustion of diesel fuel. In essence, the burner systems incorporate a fuel injector, spray atomization, proper fuel / air mixing mechanisms, and combustion control as independent heat sources.

A novel compound power-split hybrid transmission based on a modified Ravigneaux gear set is presented. The equivalent lever diagrams are used to investigate the electric operating modes for the hybrid powertrain, and then its dynamic and kinematic characteristics as well as efficiency characteristics are described in equations. A brake clutch mounted on the carrier shaft is proposed to enhance the electric driving efficiency for the hybrid transmission. Three types of electric operating mode are analyzed by the simplified combined lever diagrams and the system efficiency and torque characteristics for these electric operating modes are compared. A major influence on output torque of the hybrid transmission derived from the torque capability of motors and brake clutch is depicted.

In the hybrid brake system of electric vehicle, due to the limitation of the motor braking force when the motor is at high speed and the failure of the regenerative braking force when the motor is at low speed, there are three transitional conditions in hybrid braking: the hydraulic brake system intervenes the braking, the hydraulic brake system withdraws the braking and the regenerative braking force withdraws the braking. Due to the response speed of the hydraulic system is slower than that of the motor, there is a large braking impact (the derivative of braking deceleration) in the transitional conditions of hybrid braking, which deteriorates the smoothness and comfort in braking. Aiming at the impact caused by the poor cooperation between the hydraulic braking force and the motor braking force, a coordinated strategy of double closed-loop feedback and motor force correction is proposed in this paper.

Several types of power-split hybrid transmissions are outlined and the strengths and weaknesses of typical compound power-split prototype designs are summarized in this paper. Based on an modified Ravigneaux gear set, a novel compound power-split hybrid transmission with compact mechanical structure is presented, its dynamic and kinematic characteristics in equations and operating modes are described, and then equivalent lever diagrams are used to investigate the proposed compound power-split device. Control strategies in different operating modes are discussed with the simplified combined lever diagram, and a global optimization method is implemented to find the optimum operation point for the hybrid powertrain. To evaluate the fuel economy of a hybrid car equipped with this hybrid transmission, a forward powertrain simulation model is developed and real vehicle performance tests are conducted in the chassis dynamometer.

Durability and performance evaluation of the ageing catalyzed continuously regenerating trap (CCRT) on solid and volatile particles from diesel bus were studied through a set of transient TSI engine exhaust particle sizer spectrometer based on on-road test. Particle characteristics under stepped steady conditions and during regeneration were discussed in detail. Under idle and stepped steady conditions, total particle number and mass Emission Rate (ER) of each test presented rising trends as speed increase. Total number ERs of all tests showed downtrend as the CCRT aging. The particle number size distributions at different ageing stage showed changing characteristics due to developing filter mechanism. Compared with baseline data, the total number reduction rates at idle condition were incremental, from 91.4% to 98.9% as the CCRT ageing. Percentages of nuclei mode concentrations took higher range from 66.6% to 89.9% compared with the baseline data, 43.2-43.7%.

Idle stopping is one of the most important fuel saving methods for hybrid electric vehicle (HEV). While the enriched injection strategy which was employed to ensure reliable ignition of first cycle will leads to even more fuel film stayed in the intake port, all of the liquid film will evaporate randomly and interfere the mixture air-fuel ratio of the followed cycles. The fuel transport of the first cycle should be enhanced to reduce the residual fuel film, and then the control of the cycle-by-cycle air-fuel ratio will become easier and the combustion and HC emissions will also be better. In this paper the mixture preparation characteristics of the unfired first cycle, as well as the combustion and HC emissions characteristics of the fired first cycle under various injection timing strategies such as close-valve injection, mid-valve injection, and open-valve injection were investigated.

The present work discusses a novel oxyfuel combustion method named internal combustion rankine cycle (ICRC) used in reciprocating engines. Water is heated up through heat exchanger by exhaust gas and engine cooling system, and then injected into the cylinder near top dead center to control the combustion temperature and in-cylinder pressure rise rate, meanwhile to enhance the thermo efficiency and work of the combustion cycle. That is because injected water increases the mass of the working fluid inside the cylinder, and can make use of the combustion heat more effectively. Waste heat carried away by engine coolant and exhaust gas can be recovered and utilized in this way. This study investigates the effect of water injection temperature on the combustion and emission characteristics of an ICRC engine based on self-designed test bench. The results indicate that both indicated work and thermal efficiency increase significantly due to water injection process.

From traditional vehicle to pure electric vehicle and then to range-extended electric vehicle (ReEV), the electrification of vehicle has caused a great change in NVH characteristics. ReEV has the most complex noise and vibration problems because it behaves both like traditional vehicle and pure electric vehicle. In addition, it has its own specific NVH characteristics. Firstly, internal combustion engine drives the generator rather than drives the vehicle. Due to the structure and load change, auxiliary power unit (APU) performs specific NVH characteristics. In addition, the pure electric mode will have the high frequency noise generated from the driveline because the noise couldn't be masked by the engine. In system level, unexpected and confusing sound in passenger compartment may affect the driver's comfort and judgments. Therefore, more and more attentions on these issues should be paid. NVH study and improvement methods on ReEV are emphasized.

The weight of an exhaust system on a modern vehicle is increasing because of all kinds of reasons, like engine power's increasing, more catalysts for emission control and more NVH (Noise, Vibration and Harshness) performance requirements. After the engine starting, the exhaust system was not only bearing a cyclical load from the engine, which mainly causing the vibration of the exhaust system, but also the loads from the road, which was transferred through the wheels, the suspension system and the body. Because the exhaust system always worked in these bad conditions, its structural strength, durability and life-time were analyzed in the paper, by numerical simulation and physical correlation. By discretizing the exhaust system's CAD model, a finite element model was built. After restrict the finite element model as it in a real load condition, complete the structure stress analysis and Fatigue analysis of exhaust system's hanger with FEA analysis tools.

Accurate control of both the timing and quantity of injection events is critical for engine performance and emissions. The most serious problem which reduces the accuracy of the control operation in such systems is a time delay of the responsiveness for the opening and closing operation of the electromagnetic valve. Modern electronic control systems should be capable of driving high speed solenoid injectors at a very fast switch frequency with high efficiency and acceptable power requirements. In this paper, the dynamic characteristic of a high speed servo-hydraulic solenoid injector for diesel engine, with different driving circuits and control methods, is investigated. A pre-energizing control strategy based on a dual power supply is applied to speed up the opening response time of the injectors.

A cycle-resolved test system was designed in a Two Stage Direct Injection (TSDI) Gasoline engine to simulate the engine quick start process in an Integrated Start and Generator (ISG) Hybrid Electric Vehicle (HEV) system. Based on the test system, measurement of the in cylinder HC concentrations near the spark plug under different engine coolant temperature and cranking speed conditions were conducted using a Fast Response Flame Ionization Detector (FFID) with Sampling Spark Plug (SSP) fits, then the in-cylinder equivalence ratio near the spark plug was estimated from the measured HC concentrations. In addition, the effects of the 1st injection timing, 2nd injection timing, and total equivalence ratio on the mixture formation near the spark plug were analyzed by means of experiments.

Because of the vehicle market competitive and of the raise of customers' demanding, NVH performance became an important job, especially for new energy vehicles. As the electric vehicle moving into the direction of high speed and large torque, electric vehicle vibration and noise problems highlighted gradually. In recent years, CAE has played an increasing role in the design, development and optimization of powertrain NVH at component and system levels. The subject of this paper was the numerical and experimental evaluation of the electromagnetic and vibro-acoustic behavior of an electric powertrain. For this purpose, a coupled and fully flexible dynamics model of the electric powertrain was developed. Then electromagnetic forces including both radial and tangential force and gear mesh excitations including time-varying meshing stiffness, meshing error and meshing impact were computed, which were used to perform forced response analysis on the full FE mesh of the powertrain housing.

Being one of the most simple and basic driving scenarios, highway scenario can be one of the first scenarios to achieve autonomous driving. Both car following (CF) and lane changing (LC) are the most basic and frequent maneuver during highway driving tasks, and therefore become two key issues to focus on in recent researches about autonomous vehicle (AV). Different from conventional CF and LC researches that attach much importance to the character, psychology, perception ability, and driving experience of human drivers, more timely and accurate reactions based on fast perception and communication technology as well as the automatic actuator are hypotheses for this research. Moreover, based on these hypotheses, a modified intelligent driver model (MIDM) is proposed for AVs’ following behavior to alleviate the fluctuations caused by lane changing behaviors.

Effects of biodiesel fuel on nucleation mode particles were studied on a direct injection, high pressure common-rail diesel engine for passenger cars. Particle number and size distribution of the diesel engine were obtained using an Engine Exhaust Particle Sizer (EEPS). The base petroleum diesel, three different blend ratios of petroleum diesel/biodiesel (10%, 20% and 50% v/v biodiesel blend ratios), and the pure biodiesel fuel (obtained and converted from Jatropha seed in China) (B0, B10, B20, B50 and B100 fuels) were tested without engine modification. Experiments were performed on a series of engine operating conditions. The particle number size distribution of the engine shows unimodal or bimodal log-normal distribution. With the biodiesel blend ratios increasing, the number of nucleation mode particles increases at all test engine operating conditions and accumulation mode particles decreases at most engine operating conditions.

Air purifier has been prevalently used in the passenger vehicle cabins to reduce in-cabin UltraFine Particle (UFP) concentration. In this study, Computational Fluid Dynamics (CFD) was applied to simulate the in-cabin UFP transport and distribution under different ventilation modes with different characteristics of the air purifier. Ventilation settings, air purifier settings, and air purifier location were identified as the important factors determining the in-cabin UFP distribution and transport. Downward ventilation airflow direction and smaller ventilation air velocity can be considered by the drivers for a lower in-cabin UFP concentration. Upward airflow direction from the air purifier's inlet and larger air velocity were recommended since it led up to 50% in-cabin UFP reduction. Air purifier installed at middle ceiling of the cabin develops the most efficient airflow for UFP removal.