Search Results

Based on the experimental data of true stress-strain measured by DIC (Digital Image Correlation) combined with the data from a tensile test machine, the methodology for establishing a constitutive model for Ti40 alloy sheet is presented in this paper. The procedure is demonstrated by building the constitutive relationship for Ti40 alloy sheet. As the verification of the constitutive relationship, a force-displacement diagram is simulated by FEA (Finite Element Analysis). A comparison of force-displacement diagram obtained separately by FEA and the tensile test machine is made and the result shows that the method for establishing the constitutive relationship for Ti40 alloy sheet presented in this paper are reliable and considerately accurate.

An ion current sensor is employed in a 4 cylinder production SI engine for combustion diagnosis during combustion process, knock, and low speed pre-ignition (LSPI) detection. The results show that the ion current peak value and ion current peak phase have strong correlation with the cylinder pressure and pressure peak phase respectively. The COV of ion current integral value is greater than the COV of IMEP at the same operating condition. Results show that the ion current signal is sensitive to different lambdas. Using ion current signal, the knock in any given cylinder can be detected. Importantly, the ion sensor successfully detected the low speed pre-ignition (LSPI) about more than 20 °CA before spark ignition.

In this paper the approach of using modal parameters to detect and locate damage of automobile rear axle under experimental condition is explained. This method uses the changes in the curvature mode of the structure as the damage identification indicator to detect and locate damage. The curvature mode and the damage identification indicator are explained, the process of the identification is introduced. The method is demonstrated with a FEM (Finite Element Method) analysis on a plate under different damage conditions. And the indicator is improved with a weighting function. Then EMA (Experimental Modal Analysis) is conducted on a damaged and an undamaged rear axle of a vehicle to get the modal parameters for the damage identification indicator which later identifies and locates the damages, thus validating the introduced method.

Ion current sensing, which usually employs a spark plug as its sensor to obtain feedback signal from different types of combustion in SI engines, may be applied to HCCI combustion sensing instead of a prohibitively expensive piezoelectric pressure transducer. However, studies showed that the ion current detected by a spark plug sensor is a localized signal within the vicinity of the sensor's electrode gap, being affected by conditions around it. To find out better and feasible ion probe positions, a 3D-CFD model with a detailed surrogate mechanism containing 1423 species and 6106 reactions was employed to study the effect of stratification on ion distribution in HCCI combustion. The simulation results indicate that the monitor probe 1, 8 and 9 are more stable and reliable than the others. IONmax and dIONmax are more accurate to estimate CA50 and dQmax respectively.

The undesired shifting phenomenon(USP) occurs easily under the braking or climbing conditions etc., and its impact is the discomfort to the passengers or cause of vehicle's state contrary to the driver's intention, meanwhile, the wear of the clutch and synchronizer is increased, so their lifetime are greatly shortened. To the vehicle with dual clutch transmission (DCT), undesired shifting phenomenon will lead to frequent and unnecessary actuation of synchronizer for the use of pre-engagement synchronizer in the shifting control; therefore, its occurrence should be eliminated as far as possible. In this paper, the process of the undesired shifting of the vehicle with DCT is elaborated, then the generating cause of USP is described based on directed graph.

This paper presents the simulation of in-cylinder stratified mixture formation, spray motion, combustion and emissions in a four-stroke and four valves direct injection spark ignition (DISI) engine with a pent-roof combustion chamber by the computational fluid dynamics (CFD) code. The Extended Coherent Flame Combustion Model (ECFM), implemented in the AVL-Fire codes, was employed. The key parameters of spray characteristics related to computing settings, such as skew angle, cone angle and flow per pulse width with experimental measurements were compared. The numerical analysis is mainly focused on how the tumble flow ratio and geometry of piston bowls affect the motion of charge/spray in-cylinder, the formation of stratified mixture and the combustion and emissions (NO and CO₂) for the wall-guided stratified-charge spark-ignition DISI engine.

Internal combustion Rankine cycle (ICRC) engine uses oxygen instead of air as oxidant during the combustion process, therefore totally eliminates the emission of NOx. CO2 could be captured after separated from the exhaust gas, the latter are mainly water vapor and CO2, through condensation at a relatively low price, and thus an ultra-low emission working cycle is achieved. Moreover, water is heated up by exhaust gas and injected into the cylinder during the combustion process to control combustion temperature, and evaporation of the water mist would increase working fluid inside the cylinder, therefore enhance indicated thermal efficiency. This study investigates the combustion characteristics of a quasi ICRC on a single-cylinder SI engine fueled with propane. Gas mixture of O2/CO2 is employed to simulate EGR in order to control in-cylinder temperature.

A novel reciprocating engine version of oxy-fuel combustion cycle combined with water direct injection (known as internal combustion rankine cycle) is presented in this paper. Water is injected near top dead center to control the reaction rate of the oxy-fuel mixture, as well as the peak in-cylinder temperature. The evaporation of the water mist will increase the mass of working gas inside the cylinder, and enhances the thermo efficiency and MEP. Moreover, the injected water is heated up through heat exchangers by both engine coolant and exhaust gas, and the waste heat is effectively recovered this way. This study investigates the combustion and emission characteristics of ICRC under different engine loads based on a single-cylinder, air-cooled SI engine fueled with propane. An extra diesel injector is employed to inject water with high injection temperature (160°C).

In order to explore the generation mechanism of hot-spots on the automotive brake disc, disc tests under non-frictional thermal loads are carried out on the brake dynamometer test bench. In the tests, the oxy-acetylene flame is used as the heat source, and the distribution characteristics of the disc temperature and displacement are measured and analyzed. To confirm the mechanism of the disc deformation, a disc thermal buckling model using finite element method is established, and the key factors for the disc thermal buckling under thermal loads are further analyzed. It is found that the temperature circumferential gradient is small but the temperature radial gradient is large. The disc presents waviness deformation mode with 5th order in circumferential direction, which is the first thermal buckling mode of the disc. A method using spatial frequency spectrum has been proposed to find the critical time and load of thermal buckling.

Brake squeal shows a significant uncertainty characteristic. In this paper, a series of bench tests were carried out to study the uncertainty of brake squeal on a multi-function brake inertia dynamometer test bench. Then based on time-frequency analysis results, a creative squeal confirmation and determination method was presented, which can show the squeal variations in the domains of time, frequency and amplitude together. An uncertainty analysis method was also established, in which the statistical parameters of squeal frequency and sound pressure level (SPL), and probability density evaluation of frequency based on Quantile-Quantile Plot (QQ plot) were given. And a judgment method of the frequency doubling was devised based on numerical multiple and occurrence concurrence, as well as the uncertainty statistical analysis method considering frequency doubling. All the methods established were applied to the uncertainty analysis of brake squeal.

Research studies have suggested that changes to the ignition system are required to generate a more robust flame kernel in order to secure the ignition process for the future advanced high efficiency spark-ignition (SI) engines. In a typical inductive ignition system, the spark discharge is initiated by a transient high-power electrical breakdown and sustained by a relatively low-power glow process. The electrical breakdown is characterized as a capacitive discharge process with a small quantity of energy coming mainly from the gap parasitic capacitor. Enhancement of the breakdown is a potential avenue effectively for extending the lean limit of SI engine. In this work, the effect of high-power capacitive spark discharge on the early flame kernel growth of premixed methane-air mixtures is investigated through electrical probing and optical diagnosis.

Prediction and analysis of the thermo-mechanical coupling behavior in friction braking system is very important for the design and application of vehicle brakes, such as brake judder, brake squeal, brake wear, brake cracks, brake fade. This paper aims to establish a macro-structural model of the thermo-mechanical dynamics of the ventilated disc brake with asymmetrical outer and inner disc thickness, taking into account the friction-velocity curve of the disc pad couple acquired by testing. On the basis of finite elements analysis of the model, the predictions of the thermo-mechanical responses of the brake disc are presented, including disc transient temperature field and normal stress in radial, circular and axial directions, disc lateral deformation and disc thickness variation. Numerical predictions of the disc surface temperature and later distortion are compared with experimental measurements obtained by thermocouples and non-contact displacement sensors.