Search Results

This paper provides a description of a newly developed dynamometer capable of measuring torque at speeds up to 90,000 rpm. The development which has been made enables the dynamometer to measure output of a small single shaft gas turbine engine without a speed reducing gear box. The unit consists of a high speed generator to absorb the power and a torque measuring device. Since the generator is a key component of this dynamometer, a substantial portion of this paper is devoted to describing the configuration of the generator and the design considerations, as well as its performance. The rotational speed of turbomachines is gradually being increased and will be accelerated further as ceramic materials are introduced. The subjects to be discussed here will, hopefully, be of some use when a torque measuring device for speeds over 100,000 rpm becomes necessary.

A new 4.5 liter in-line 6 cylinder engine,1 FZ-FE has been developed for the Toyota Land Cruiser. To obtain high power, fuel efficient engine, we adopted the most advanced Toyota technologies, such as Toyota original 4 Valve DOHC system with scissors gear between camshafts, compact combustion chamber with smooth inlet and outlet system, KCS and so on. The engine produces 212 HP at 4600 rpm and 275 ft-lbs at 3200 rpm. Aluminum cylinder head,short skirt cylinder block stiffened with aluminum oil pan give the engine light weight and make it rigid enough to have low vibration and quietness. And we also designed every engine part appropriately so as to make the engine durable enough in severe operating condition of off-road vehicle.

Transmission error is the main cause of gear noise in automobile transmissions, and recently can be estimated by numerical analysis [1]. First, in this report, we establish the accurate numerical analysis of transmission error by using FE analysis and Hertz's contact analysis of gear tooth stiffness. Secondly, on the basis of the established numerical analysis, we develop a new tooth flank form to reduce transmission error. The new tooth flank form aims to ensure the coincidence of meshing stiffness at all meshing positions. Finally, a validation test using an experimental prototype is performed, and we confirm that the estimated effect by the new tooth flank form has been obtained.

A new experimental method, that enables to estimate the body and driveline sensitivity to unit transmitting error of a hypoid gear for automotive rear axle gear noise, has been developed. Measurements were made by exciting the tooth of the drive-pinion gear and that of the ring gear separately using the special devices designed with regard to simulation of acceleration and deceleration. The characteristic of this method is to estimate the forces at the contact point of the gears. Estimation of these forces is carried out under the condition that the higher stiffness is provided by the tooth of the drive-pinion gear and that of the ring gear, compared with the stiffness of the driveshafts and that of the propeller shaft etc., and relative angular displacement of the torsional vibration between the teeth of the drive-pinion gear and those of the ring gear is constant.

A laboratory scale simulation test method was developed to evaluate deterioration of radial lip seals of fluoroelastomer (FKM) compounds for engine crankshafts. The investigation of the collected radial lip seals of FKM compounds from the field with service up to 450,000km indicated that the only symptom of deterioration is a decrease of lip interference. This deterioration was not duplicated under conventional test conditions using an oil seal test machine because sludge build up at the seal lip caused oil leakage. However, revised test conditions make it possible to duplicate the deterioration experienced in the field. An immersion test using a radial lip seal assembled with the mating shaft was newly developed. This test method was found to be useful to evaluate deterioration of radial lip seals using FKM compounds. Oil additives affect the deterioration of lip seal materials significantly. Therefore, immersion tests of four different oils were conducted to evaluate this effect.

To meet the requirement for higher performance engine bearings, the microgrooved bearings, that is the plain bearings with shallow circumferential grooves, have been developed. Recently, the performance of microgrooved bearings obtained experimentally have reported1)2). The authors calculated the bearing performance of the microgrooved bearings by elastohydrodynamic lubrication theory. In this paper, the authors described thecalculation method and the performance of the microgrooved bearings obtained theoretically.

A discomforting noise can sometimes be heard in a vehicle passenger compartment during acceleration which can be annoying to passengers. We call this noise a “rumbling noise”. A detailed study of the rumbling noise spectrum has clarified the generating mechanism of the rumbling noise and the relation between the spectral structure and the tone. In order to analyze the rumbling noise, we simulated it with electrically synthesized noise. This method showed that at the times when the noise is heard there are always more than three discrete harmonics which are half an order harmonics of the engine revolution. The sensation of discomfort depends on the phase, frequency and magnitude of each frequency component. To evaluate the noise quantitatively, we also analyzed the shape of the time domain noise envelope. The envelope shape has a good correlation with the feelings of discomfort.

Brake squeal is caused by dynamic instability, which is influenced by its dynamic unstable structure and small disturbance of friction force variation. Recently, FE Analysis of brake squeal is applied for brake design refinements, which is based on dynamic instability theory. As same as the refinement of brake structure is required for brake squeal reduction, the refinement of pad materials is also required for brake effectiveness and brake squeal reduction. It is well known that friction film, which is composed of polymers like phenol formaldehyde resin and so on, influences for friction coefficient. Therefore it is expected that the refinement of polymers in pad materials enable higher brake effectiveness and less brake squeal. In this paper, Molecular Dynamics is applied for the friction force variation of polymers in pad materials. The MD simulation results suggest the reduction method of friction force variation of polymers.

A new method to predict low-frequency brake squeal occurrence was developed and guidelines for its elimination were formulated. First, a characteristic of the phenomenon was investigated using a simplified three-degree-of-freedom system model to obtain guidelines for squeal elimination, such as the natural frequency ratio of the brake rotor and caliper, an equivalent mass ratio of the brake rotor and caliper and the natural frequency and damping coefficient of the dynamic absorber. Then, a practical finite element model of the disk brake system was developed using Substructure Synthesis Method for design stage predictions. Finally, the usefulness of this method was confirmed by experimental validation.

This paper describes an unique concept for the optimum design of tooth modifications of helical gears. The tooth modifications of helical gears will minimize transmission error under various loads with flexible supporting members, i.e. automobile transmissions. The key point of this concept is the amount of tooth modifications on each path of contact moved by misalignment under each respective target torque. Using this concept, it is possible to calculate the optimum 3-dimensional tooth modifications. The tooth modifications under light load will be a small curvature, and a large curvature under high load. Furthermore, through observation we can determine that the tooth surface modifications will have excellent impact on transmission error over a wide torque range. Finally, this method is verified experimentally in various misalignment conditions.

It is well known that disc brake squeal is often caused by high friction coefficient pad materials. Disc brake squeal is caused by dynamic unstable system under small disturbance of friction force variation. Today, disc brake squeal comes to be simulated by FEA, but it is very difficult to put so many dynamic unstable solutions into stable solutions. Therefore it is very important to make it clear the influence of friction force variation. This paper describes a study on trigger of disc brake squeal generation. First, the development of experimental set-up for disc brake squeal basic research and experimental results are described. Second, the equation of motion in disc brake squeal is derived and the vibration induced by small disturbance are analyzed. Furthermore, kinetic energy increase per 1 cycle in minute vibration are calculated, which represents the influence of friction and wear between disc and pad with caliper.

The effects of multiple-injection on exhaust emissions and performance in a small HSDI (High Speed Direct Injection) Diesel engine were examined. The causes for the improvement were investigated using both in-cylinder observation and three-dimensional numerical analysis methods. It is possible to increase the maximum torque, which is limited by the exhaust smoke number, while decreasing the combustion noise under low speed and full load conditions by advancing the timing of the pilot injection. Dividing this early-timed pilot injection into two with a small fuel amount is effective for further decreasing the noise while suppressing the increase in HC emission and fuel consumption. This is realized by the reduced amount of adhered fuel to the cylinder wall. At light loads, the amount of pilot injection fuel must be reduced, and the injection must be timed just prior to the main injection in order to suppress a possible increase in smoke and HC.

Porous material is used at the duct wall in order to reduce air resonance in the air intake duct. High frequency component in the intake noise is reduced by escaping of the air through the duct wall. The relation of attached position, the size and air permeability of the porous material to acoustic behaviors was cleared.

An active engine mount using a piezo actuator for a large vibrational amplitude is discussed. As a piezo actuator has a small displacement, the active mount requires a mechanism to increase the displacement of the piezo actuator to sufficiently counteract vibration. This paper describes in detail the construction of the prototype and the background theory from which the increase in displacement was achieved. Secondary, it describes a proving test performed on an experimental device that simulates the transfer of vibration from the engine to the chassis through the piezo active mounts. Finally it reports the decrease in floor vibration achieved when a piezo active mount was installed on an experimental vehicle.

In recent years, a number of different Blind Spot Monitor (BSM) systems have become more and more popular in North American automotive market. The BSM system advises the driver of vehicles travelling in adjacent lanes when these vehicles are also in the driver's outside rearview mirror blind spots. Similarly, when the vehicle is backing up from a parking spot, cross-traffic vehicles can be in the driver's outside mirror blind spots. In this situation, the Rear Cross Traffic Alert (RCTA) system alerts the driver when the driver shifts the vehicle in the reverse gear and there are approaching cross-traffic vehicles. The benefits of RCTA system was presented by [1]. The RCTA alert studied in this paper is given by playing an audible sound and by flashing the outside mirror indicators. The RCTA and BSM systems share the same vehicle sensors and most of their vehicle components.

This paper presents a new method of predicting judder occurrence. In this method, the friction characteristics of the clutch, that is, the relationship between the slip speed and the friction coefficient, and torsional vibration characteristics of the drive line are both considered. Judder occurrence is judged by calculating complex eigen values of a torsional vibration model of the drive line considering the clutch friction characteristics. This method is applied to judder phenomena of automatic transmissions. Comparisons between calculations and experiments are shown. Studies of the influence of viscous damping coefficients of drive line units are also described.

The present paper describes an application of non-parametric shape optimization to disc brake squeal phenomena. A main problem is defined as complex eigenvalue problem in which the real part of the complex eigenvalue causing the brake squeal is chosen as an objective cost function. The Fre´chet derivative of the objective cost function with respect to the domain variation, named as the shape derivative of the objective cost function, is evaluated using the solution of the main problem and the adjoint problem. A selection criterion of the adoptive mode number in component mode synthesis (CMS), which is used in the main problem, is presented in order to reduce the computational error in complex eigenvalue pairs. A scheme to solve the shape optimization problem is presented using an iterative algorithm based on the H1 gradient method for reshaping. For an application of the optimization method, a numerical example of a practical disc brake model is presented.

Recently engine sound quality is becoming more noticeable as noise level in a vehicle passenger compartment has been decreasing. It is necessary to reduce such discomforting noise as rumbling noise in order to improve engine sound quality. This paper describes the experimental study to find out causes of rumbling noise in an engine structure and several investigations to reduce rumbling noise. Some new approaches have been introduced to evaluate the influence of an combustion impact, the movement of a crankshaft, timing of rumbling noise and so on. The result shows that the primary cause of rumbling noise is the movement of a crankshaft due to the impact of combustion and next is the vibration characteristics of the engine-transmission assembly (power plant). Finally superior engine sound quality is achieved by increasing counterweights and stiffness of a crankshaft and also by optimizing the spark advance and improving vibration characteristics of various engine parts.

The vehicle requires high brake performance and mass reduction of disc brake for vehicle fuel economy. Then disc brake will be designed by downsizing of disc and high friction coefficient pad materials. It is well known that disc brake squeal is frequently caused by high friction coefficient pad materials. Disc brake squeal is caused by dynamic unstable system under disturbance of friction force variation. Today, disc brake squeal comes to be simulated by FEA, but it is very difficult to put so many dynamic unstable solutions into stable solutions. Therefore it is very important to make it clear the influence of friction force variation. This paper describes the development of experimental set up for disc brake squeal basic research. First, the equation of motion in low-frequency disc brake squeal around 2 kHz is derived.

In emerging markets, Port Fuel Injection (PFI) technology retains a higher market share than Gasoline Direct Injection (GDI) technology. In these markets fuel quality remains a concern even despite an overall improvement in quality. Typical PFI engines are sensitive to fuel quality regardless of brand, engine architecture, or cylinder configuration. One of the well-known impacts of fuel quality on PFI engines is the formation of Intake Valve Deposits (IVD). These deposits steadily accumulate over time and can lead to a deterioration of engine performance. IVD formation mechanisms have been characterized in previous studies. However, no test is available on a state-of-the-art engine to study the impact of fuel components on IVD formation. Therefore, a proprietary engine test was developed to test several chemistries. Sixteen fuel blends were tested. The deposit formation mechanism has been studied and analysed.