Search Results

In order to correspond to the exhaust emissions regulations that become severe every year, more advanced engine control becomes necessary. Engine engineers are concerned about the Hydrocarbons (HCs) that flow through the air-intake ports and that are difficult to precisely control. The main sources of the HCs are, the canister purge, PCV, back-flow gas through the intake valves, and Air / Fuel ratio (A/F) may be aggravated when they flow into the combustion chambers. The influences HCs give on the A/F may also grow even greater, which is due to the increasingly stringent EVAP emission regulations, by more effective ventilation in the crankcase, and also by the growth of the VVT-operated angle and timing, respectively. In order to control the A/F more correctly, it is important to estimate the amount of HCs that are difficult to manage, and seek for suitable controls over fuel injection and so on.

A new 4.5 liter in-line 6 cylinder engine,1 FZ-FE has been developed for the Toyota Land Cruiser. To obtain high power, fuel efficient engine, we adopted the most advanced Toyota technologies, such as Toyota original 4 Valve DOHC system with scissors gear between camshafts, compact combustion chamber with smooth inlet and outlet system, KCS and so on. The engine produces 212 HP at 4600 rpm and 275 ft-lbs at 3200 rpm. Aluminum cylinder head,short skirt cylinder block stiffened with aluminum oil pan give the engine light weight and make it rigid enough to have low vibration and quietness. And we also designed every engine part appropriately so as to make the engine durable enough in severe operating condition of off-road vehicle.

A new test machine has been developed which can evaluate vibration due to stick-slip using an actual full-scale clutch pack. Using this machine, a static breakaway friction coefficient measurement test method and a stick-slip test method have been established. Both methods have been shown to provide results which correlate with the results from both a full-scale assembly test and a vehicle shudder evaluation test. The evaluation of the frictional properties of commercial oils using these test methods showed that the static breakaway friction coefficient and the stick-slip properties have generally contradictory performance to each other for automatic transmission. The study of the frictional properties for typical additives and an analysis of the surface of the steel plates with ESCA (Electron Spectroscopy for Chemical Analysis) showed that the frictional properties are significantly affected by the additives adsorbed on the clutch plate sliding surface.

A discomforting noise can sometimes be heard in a vehicle passenger compartment during acceleration which can be annoying to passengers. We call this noise a “rumbling noise”. A detailed study of the rumbling noise spectrum has clarified the generating mechanism of the rumbling noise and the relation between the spectral structure and the tone. In order to analyze the rumbling noise, we simulated it with electrically synthesized noise. This method showed that at the times when the noise is heard there are always more than three discrete harmonics which are half an order harmonics of the engine revolution. The sensation of discomfort depends on the phase, frequency and magnitude of each frequency component. To evaluate the noise quantitatively, we also analyzed the shape of the time domain noise envelope. The envelope shape has a good correlation with the feelings of discomfort.

In the field of automobile disk wheels, demands for aluminum wheels have been increasing for the reason of ride comfort and better appearance. And over 90 percent of luxurious passenger cars are equipped with aluminum wheels. This trend is spurred also by the demand for higher fuel efficiency for the cause of environmental protection, which calls for weight reduction of automobiles. This paper reports our research on manufacturing light-weight, high-quality aluminum cast wheels; covering the entire process from basic design to casting, and placing emphasis on the following three points. 1) Determination of optimum wheel configuration through computer simulation 2) Selection of optimum material composition 3) Optimization of the thin plate casting conditions Combination of the above technologies developed for the purpose of weight reduction resulted in the weight reduction of approximately 20% over the conventional aluminum wheels.

On board multiplexing communication system is regarded as a necessary technology for the future of electronic system in automobiles. Many companies are developing multiplexing systems and the ISO and SAE are active in establishing standards for communication protocols. The proposed communication protocol specifications have different specifications. Consequently, no compatible evaluation standards existed, and it was difficult to compare one protocol to another. Therefore, to assist the standardization activities of the IS0 and SAE, we have developed an evaluation method for distributed multiplexed communication systems and evaluated each of the proposed protocols using this method. These evaluations were performed from the point of view of the future users of these systems. In this paper we present the results of the experiments on distributed multiplexed communication systems each of which consists of communication IC and the proposed physical layer.

Sintered silicon nitride, particularly in structural ceramics, has superior properties such as low weight, heat resistance, wear resistance, etc. It is already being applied to automobile engine parts such as the swirl chamber and the turbine rotor. In recent years, the strength of silicon nitride has shown to be above 1000MPa. This has been achieved through advances in manufacturing technology such as materials powder, forming, sintering and so on. But the silicon nitride is easily damaged during grinding because it has less fracture toughness than metal. Consequently, the inherent strength of the material is not demonstrated in the actual products presently produced. It is assumed that the main cause of strength reduction is microcrack. In ordinary grinding methods, the length of microcrack has been estimated at approximately twenty micrometers by fracture mechanics analysis.

Vehicle stability after releasing the accelerator during limit cornering (from now on “Tuck-in”) is the behavior that the turning radius of a vehicle gets smaller after releasing the accelerator. This paper presents that the main factors of yaw moment variation by releasing the accelerator are the change of lateral forces due to longitudinal transfer of normal loads, lateral shift of vehicle center of gravity due to vehicle roll and tire lateral deflection, and the change of lateral forces due to deceleration. It also shows that roll stiffness distribution and longitudinal acceleration have an influence through the formulation of turning radius ratio.

Toyota participated in Formula One1 (F1) Racing from 2002 to 2009. As a result of the downturn in the world economy, various engine developments within F1 were restricted in order to reduce the cost of competing in F1. The limit on the maximum number of engines allowed has decreased year by year. Toyota focused on the engine performance deterioration due to the combustion chamber deposits. In 2009, Toyota was successful in reducing around 40% of the deterioration by making combustion chamber cleaner in cooperation with ExxonMobil. This contributed to good result of 2009 F1 season for Toyota, including two second place finishes.

The anti-shudder effect of ATF additives and their mechanisms have been investigated. Anti-shudder durability was evaluated using an automatic transmission (AT) on an engine stand under continuously slip-controlled condition. The addition of over-based Ca-sulfonate and friction modifier (FM) remarkably improved the anti-shudder durability of ATF. The surface roughness of the contact area (contact area roughness) of the clutch plates was measured by an electron probe surface roughness analyzer. To evaluate the boundary frictional properties of the adsorbed film formed, the friction coefficient of the clutch plates in the absence of oil was examined after the anti-shudder durability test. It was found that shudder occurrence was strongly correlated with the contact area roughness and the boundary frictional property of the steel plate surface. Large contact area roughness and low boundary friction were preferred to prevent shudder.

The recent growth of available computational resources has enabled the automotive industry to utilize unsteady Computational Fluid Dynamics (CFD) for their product development on a regular basis. Over the past years, it has been confirmed that unsteady CFD can accurately simulate the transient flow field around complex geometries. Concerning the aerodynamic properties of road vehicles, the detailed analysis of the transient flow field can help to improve the driving stability. Until now, however, there haven’t been many investigations that successfully identified a specific transient phenomenon from a simulated flow field corresponding to driving stability. This is because the unsteady flow field around a vehicle consists of various time and length scales and is therefore too complex to be analyzed with the same strategies as for steady state results.

This paper describes the multiplex communication protocol, BEAN (Body Electronics Area Network), developed for body control system on passenger cars which in recent years has increased the scope of multiplex communication. BEAN is based on a protocol developed in 1992 (SAE920231) but expands upon the performance in areas, such as the suitability of the ID system for increase of ECUs, the variable data length enabling the transmission of diagnostic data, and the transmission rate, while keeping the cost and radiation noise level low. The software size of BEAN is compact enough to be implemented by general purpose 8bit MCUs which have recently seen improvements in performance. The BEAN communication devices are available corresponding to the scale of the application and configuration of the ECU taking into account the software capability. This protocol was evaluated using simulation with the body control system on luxury passenger cars.

An analysis system for vehicle noise and vibration has been developed. It consists of minicomputer based analog processing system connected with a large main-frame computer. This system features multi-modes for data analysis, fast data processing, data compatibility with conventional analog systems and feasibility. Fast data processing was achieved by newly developed FFT processor and minicomputer software. A new remote control box makes it simple to operate. Data processed by the minicomputer can be transferred to a large mainframe computer for further analysis.

Toyota Motor Corporation has developed a new 6-speed automatic transmission (U660E) for the front-wheel drive vehicles and large displacement engines. The U660 E was adapted to achieve improved environmental protection, and meet safety standards, which are large concerns for the society and customer satisfaction, by being small, light, highly efficient, quick response, and high shift quality. Toyota fundamentally improved both the hardware and software of the control system to meet these important goals.

Vehicles equipped with in-wheel motors are being studied and developed as a type of electric vehicle. Since these motors are attached to the suspension, a large vertical suspension reaction force is generated during driving. Based on this mechanism, this paper describes the development of a method for independently controlling roll and pitch as well as yaw using driving force distribution control at each wheel. It also details the theoretical calculation of a method for decoupling the dynamic motions. Finally, it describes the application of these 3D dynamic motion control methods to a test vehicle and the confirmation of the performance improvement.

1G engine series consists of four types of 2-liter, in-line, 6-cylinder gasoline engines for passenger cars, with different performance characteristics to meet diversified market demands. These engines are already put into mass production. The original engine - 1G-EU - is a compact and light weight 2-valve OHC engine with the maximum power 77 kW/5200 rpm. The 1G-GEU is a 4-valve DOHC engine developed on the basis of the 1G-EU engine, with a higher performance and a higher power of 103 kW/6200 rpm. The 1G-GZEU is a mechanical supercharging type engine based on the 1G-GEU, with a remarkably improved performance in the low and medium engine speed ranges, and the highest power of 110 kW/6000 rpm. The 1G-GTEI! is a turbocharging type engine also based on the 1G-GEU, with a markedly improved performance in the medium and high speed ranges, and the high power of 136 kW/6200 rpm. A number of new technologies were introduced on development of these engines.

Countries and regions around the world are tightening emissions regulations in reaction to the increasing awareness of environmental conservation. At the same time, growing concerns about the depletion of raw materials as vehicle ownership continues to increase is prompting automakers to look for ways of decreasing the use of platinum-group metals (PGMs) in the exhaust systems. This research has developed a new catalyst with strong robustness against fluctuations in the exhaust gas and excellent nitrogen oxide (NOx) conversion performance. This catalyst incorporates rhodium (Rh) clusters with a particle size of several nanometers, and stabilized CeO2-ZrO2 solid-solution (CZ) with a pyrochlore crystal structure as a high-volume oxygen storage capacity (OSC) material with a slow O2 storage rate.

Recently, there has been a tendency of high power and high speed in automotive engines. In addition they have been also required high reliability. And engine bearings have been required to be advanced in wear resistance as well as seizure resistance. Therefore, copper-lead alloy bearings with overlay, which have better seizure resistance, have been widely used for high speed engines up to the present. But it becomes very important for them to advance the overlay wear resistance. In this paper, the composite overlay is mainly researched to improve wear resistance regarding kind of hard particles and their amounts in the overlay.

Diesel engines with relatively good fuel economy are known as an effective means of reducing CO₂ emissions. It is expected that diesel engines will continue to expand as efforts to slow global warming are intensified. Diesel particulate and NOx reduction system (DPNR), which was first developed in 2003 for introduction in the Japanese and European markets, shows high purification performance which can meet more stringent regulations in the future. However, it is poisoned by sulfur components in exhaust gas derived from fuel and lubricant. We then developed the sulfur trap DPNR with a sulfur trap catalyst that traps sulfur components in the exhaust gas. High purification performance could be achieved with a small amount of platinum group metal (PGM) due to prevention of sulfur poisoning and thermal deterioration.

New ductile cast iron flywheel integrated with gear and its manufacturing process were developed to reduce the manufacturing steps and cost compared with conventional flywheel around which a steel ring gear is fit. In this process, the ring gear teeth around a cast iron flywheel are formed directly in net shape and free from any defect by the hot form-rolling method, followed by the thermomechanical treatment in a short time. The gear is superior to that made by the conventional hobbing and heat treatment in accuracy, strength and anti-wear property.