Search Results

A new experimental method, that enables to estimate the body and driveline sensitivity to unit transmitting error of a hypoid gear for automotive rear axle gear noise, has been developed. Measurements were made by exciting the tooth of the drive-pinion gear and that of the ring gear separately using the special devices designed with regard to simulation of acceleration and deceleration. The characteristic of this method is to estimate the forces at the contact point of the gears. Estimation of these forces is carried out under the condition that the higher stiffness is provided by the tooth of the drive-pinion gear and that of the ring gear, compared with the stiffness of the driveshafts and that of the propeller shaft etc., and relative angular displacement of the torsional vibration between the teeth of the drive-pinion gear and those of the ring gear is constant.

A discomforting noise can sometimes be heard in a vehicle passenger compartment during acceleration which can be annoying to passengers. We call this noise a “rumbling noise”. A detailed study of the rumbling noise spectrum has clarified the generating mechanism of the rumbling noise and the relation between the spectral structure and the tone. In order to analyze the rumbling noise, we simulated it with electrically synthesized noise. This method showed that at the times when the noise is heard there are always more than three discrete harmonics which are half an order harmonics of the engine revolution. The sensation of discomfort depends on the phase, frequency and magnitude of each frequency component. To evaluate the noise quantitatively, we also analyzed the shape of the time domain noise envelope. The envelope shape has a good correlation with the feelings of discomfort.

Methyl esters of saturated/unsaturated higher aliphatic acids (FAMEs) and a FAME of waste cooking oil (WCOME) were heated at 120°C in an air gas flow. The samples were analyzed before and after heating, using six different methods including electrospray ionization mass spectrometry. As a result, the samples after heating were found to contain low molecular weight aliphatic compounds and oligomers of the FAME. Based on the chemical structure of these oxidation products, reaction schemes were proposed for the deterioration of FAMEs. In addition, two unsaturated FAMEs containing 2,6-di-t-butyl-p-cresol (BHT) were similarly heated and analyzed to examine the effect of BHT on the oxidation of these FAME.

The authors developed a useful analysis method of the rotational-angle of gear under transient state using the Hilbert Transform because the conventional method was not available under the transient state. Here, under the transient state the gear revolution speed was changed from 600r/min to 2000r/min in 0.35 seconds. A key technology of this method was that Hilbert Transform method, which used to be applicable only for steady data was improved so that it could treat transient data. Hence, the following procedures were developed. 1. The rotation of gear-teeth was detected by a gap-sensor pair, which can cancel the measuring error due to fluctuation of gear shaft. 2. The frequency of such signals varied significantly by the gear-revolution speed. Transient gear-teeth detection signals obtained at a constant sampling rate were converted to almost-constant frequency signals over the data series axis using a trigger pulse obtained per gear revolution.

Vehicle stability after releasing the accelerator during limit cornering (from now on “Tuck-in”) is the behavior that the turning radius of a vehicle gets smaller after releasing the accelerator. This paper presents that the main factors of yaw moment variation by releasing the accelerator are the change of lateral forces due to longitudinal transfer of normal loads, lateral shift of vehicle center of gravity due to vehicle roll and tire lateral deflection, and the change of lateral forces due to deceleration. It also shows that roll stiffness distribution and longitudinal acceleration have an influence through the formulation of turning radius ratio.

The effect of GTL diesel fuel on organic materials used in fuel delivery systems of vehicles was investigated. Specimens made from 16 kinds of organic materials were immersed in GTL diesel fuels synthesized at Refinery-A and Refinery-B (referred to as GTL-A and GTL-B, respectively) and then subjected to tensile testing. The tensile test results revealed that elongation of the nylon sample immersed in GTL-A was extremely small, about 4% of that of untreated nylon. In the light of this finding, the GTL diesel fuels and nylons before and after immersion test were analyzed in detail using about 20 analysis methods to determine the cause for poor elongation. The following points were found. (1) GTL-A consisted of low molecular-weight paraffins. (2) GTL-A had low molecular-weight i-paraffins. (3) The nylon immersed in GTL-A contained low molecular-weight paraffins. (4) The paraffins in the nylon immersed in GTL-A were richer in i-paraffins than the original GTL-A.

In a previous paper (Part 1 of this series), nylon-66 specimens were immersed in two GTL diesel fuels (GTL-A and GTL-B) and then subjected to tensile testing. The tensile test results revealed that the elongation of the specimen immersed in GTL-A was dramatically reduced. The GTL diesel fuels and nylon specimens before and after immersion were analyzed to determine the cause of the decline in elongation. It was found that the poor elongation was caused by penetration and oxidation of low molecular-weight paraffins and that the ease of penetration and oxidation of paraffin depended on the structure of paraffin. In this paper, the low molecular-weight paraffins detected in GTL-A were mixed to produce model fuels. Then, pieces of nylon cut from the tensile test specimen, were immersed in the model fuels. In addition, partial oxidation products of the paraffin (alcohol, aldehyde or ketone and acid) were used in immersion tests of the nylon pieces.

The recent growth of available computational resources has enabled the automotive industry to utilize unsteady Computational Fluid Dynamics (CFD) for their product development on a regular basis. Over the past years, it has been confirmed that unsteady CFD can accurately simulate the transient flow field around complex geometries. Concerning the aerodynamic properties of road vehicles, the detailed analysis of the transient flow field can help to improve the driving stability. Until now, however, there haven’t been many investigations that successfully identified a specific transient phenomenon from a simulated flow field corresponding to driving stability. This is because the unsteady flow field around a vehicle consists of various time and length scales and is therefore too complex to be analyzed with the same strategies as for steady state results.

A communication system that uses roadside beacons to broadcast road and traffic information and private messages to vehicles has been developed. The system, called Road/Automobile Communication System (RACS), was the result of a joint research project involving the Public Works Research Institute and 25 private-sector corporations. This paper contains an outline of RACS and of an onboard system developed by TOYOTA and presents the results of field tests conducted in the Tokyo area. The results not only verify the capability of the RACS system and the effectiveness of the in-vehicle equipment but also indicate the potential of such a beacon based network to improve traffic jam and driving safety whilst providing enhanced communication facilities without increasing radio-wave congestion.

In recent years Road Departure Mitigation Systems (RDMS) is introduced to the market for avoiding roadway departure collisions. To support the performance testing of the RDMS, the most commonly seen road edge, grass, is studied in this paper for the development of standard surrogate grass. This paper proposes a method for defining the resembling grass color and height features due to significant variations of grass appearances in different seasons, temperatures and environments. Randomly selected Google Street View images with grass road edges are gathered and analyzed. Image processing techniques are deployed to obtain the grass color distributions. The height of the grass is determined by referencing the gathered images with measured grass heights. The representative colors and heights of grass are derived as the specifications of surrogate grass for the standard evaluation of RDMS.

This paper investigates a new approach to the quantification technique for road induced vehicle interior noise and vibration within the frequency range up to 40 Hz. By employing the least squares method, both vertical and fore-aft load to each wheel were quantified using transfer function and actual vibration response of the vehicle driven on a road. The coupled structural-acoustic vehicle model using the finite element method, which is also detailed in this paper, is combined with the quantified input load to simulate road induced interior noise and vibration response. Experimental verification, which indicates reasonable accuracy of the simulation, and an application for the prototype development are also presented.

The muffler layout in the exhaust system has been optimized for the attenuation of exhaust noise which has not been studied much to this date. As a result, “Exhaust Manifold Muffler” has been developed. This unit is capable of efficiently muffling the primary and secondary componemts of the engine explosion stroke noise. Such task is achieved without deterioration of engine performance by allocating the volume at the junction of the exhaust manifold branch pipes. Acoustic characteristics of “Exhaust Manifold Muffler” have been analyzed by FEM and experimental methods, which have shown that not only does the volume placed at the junction of the exhaust manifold branch pipes work as a conventional muffler, but also prevents the exhaust manifold branch pipes from amplifying exhaust noise. This is the reason why “Exhaust Manifold Muffler” can muffle more efficiently than the conventional muffler.

Filiform corrosion phenomenon and its prevention method for 5000 series aluminum alloy sheet have been investigated. The painted aluminum alloy sheets were subject significantly to filiform corrosion caused by formation of a mottled and coarse zinc phosphate film during chemical conversion process. On the other hand, galvanized aluminum alloy sheet showed an uniform and fine phosphate film in a brief time and the filiform corrosion resistance was improved markedly. The test results of press-forming and corrosion for the prototype engine hoods made of this newly developed galvanized sheets have revealed a good formability and an excellent filiform corrosion resistance.

Previous reports have already described the details of engine start-shock and the mechanism of vibration mechanism in a stationary vehicle. This vibration can be reduced by optimized engine and motor generator vibration-reduction controls. A prediction method using a full-vehicle MBD model has also been developed and applied in actual vehicle development. This paper describes the outline of a new method for the hybrid system of mechanical power split device with two motors that predicts engine start-shock when the vehicle is accelerating while the engine is stopped. It also describes the results of mechanism analysis and component contribution analysis. This method targets engine start-shock caused by driving torque demand during acceleration after vehicle take-off. The hybrid control system is modeled by MATLAB/Simulink. A power management and motor generator control program used in actual vehicles is installed into the main part of the control system model.

The new Toyota FCV “Mirai” has reduced the weight, size, and cost of the high-pressure hydrogen storage system while improving fueling performance. The four 70 MPa tanks used on the 2008 Toyota FCHV-adv were reduced to two new larger diameter tanks. The laminated structure of the tanks was optimized to reduce weight, and a high-strength low-cost carbon fiber material was newly developed and adopted. The size of the high-pressure valve was reduced by improving its structure and a high-pressure sensor from a conventional vehicle was modified for use in a high-pressure hydrogen atmosphere. These innovations helped to improve the weight of the whole storage system by approximately 15% in comparison with Toyota FCHV-adv, while reducing the number of component parts by half and substantially reducing cost. The time required to fuel the FCV was greatly reduced by chilling the filling gas temperature at the hydrogen filling station to −40°C (as per SAE J2601).

Toyota Hybrid System (THS), that combines a gasoline engine and an electric motor was installed in the Prius, which was introduced in 1997 as the world's first mass-produced hybrid passenger car, and was vastly improved in 2003. The new Prius gained a status of highly innovative and practical vehicle. In 2005, combined with a V6 engine, THS had a further evolution as a Hybrid System for SUV, which was installed in the RX400h and Highlander Hybrid to be introduced into the world. This report will explain “new THS” which achieved both V8 engine power performance and compact class fuel economy, while securing the most stringent emission standard, SULEV.

A new method to measure in-cylinder flame propagation and mixture distribution has been developed. The distribution is derived from analyzing the temporal history of flame spectra of CH* and C2*, which are detected by a spark plug type sensor with multi-optical fibers. The validity of this method was confirmed by verifying that the measurement results corresponded with the results of high speed flame visualization and laser induced fluorescence (LIF) measurement. This method was also applied to analysis of cyclic combustion fluctuation on start-up in a direct injection spark ignition (DISI) engine, and its applicability was confirmed.

In the field of automotive gasoline engines, new products aiming at greater fuel economy and cleaner exhaust gases are under development with the aim of preventing environmental destruction. Severe ignition environments such as lean combustion, stronger charge motion, and large quantities of EGR require ever greater combustion stability. In an effort to meet these requirements, an iridium plug has been developed that achieves high ignitability and long service life through reduction of its diameter, using a highly wear-resistant iridium alloy as the center electrode.(1)(2) Recently, direct injection engines have attracted attention. In stratified combustion, a feature of the direct injection engine, the introduction of rich air-fuel mixtures in the vicinity of the plug ignition region tends to cause carbon fouling. This necessitates plug carbon fouling resistance.

We developed a new Manual Transmission Gear Oil (MTF) named LV for improved fuel economy and CO2 reduction. MTF LV is a low viscosity fluid to reduce stir losses at lower temperatures. In general, low viscosity fluids can cause metal fatigue, wear and seizure. The MTF LV was designed to overcome these problems by maintaining the oil film thickness after it is deteriorated and improving the wear characteristics with additives. As a result, the MTF LV provides equal or better durability than the current MTF. In addition, it also has good performance at low temperatures, better shift feeling characteristics, and improved oxidation stability.

In developing an oxidation catalyst for reducing diesel particulates, it is necessary to balance two conflicting characteristics. One is high oxidizing activity so that the catalyst can reduce the Soluble Organic Fraction (SOF) efficiency even at low exhaust temperatures. The other is the suppression of sulphate formation at high exhaust temperatures. First it was studied that active metals and coating materials are given effects on the reduction of SOF, the formulation of sulphate and durability, by using catalysts equivalent in composition to the oxidation catalyst for gasoline-engines. Based on these findings, a two-stage catalyst wasdeveloped. It satisfies the two characteristics at a comparatively high levelby slecting materials and optimizing the catalyst composition.