Search Results

The environment is one of the most important issues currently facing the world and the automobile industry is required to respond with eco-cars. To meet this requirement, the hybrid vehicle is one of the most optimal solutions. The hybrid system automatically stops engine idling (idling stop), or stops the engine during deceleration to recover energy. The engine stop however creates a problem concerning the vehicle's climate control system. Because the conventional climate control system incorporates a compressor driven by engine belt, there is almost no cooling performance while the engine is stopped. Until now, when a driver needed more cooling comfort the engine has been switched back on as a compromise measure. To realize cabin comfort that is consistent with fuel saving, a 2-way driven compressor has been developed that can be driven both by engine belt while the engine is running and by electric motor when the engine is stopped.

As part of the International Lubricant Standardization and Approval Committee's (ILSAC) goal of developing a global automatic transmission fluid (ATF) specification, members have been evaluating test methods that are currently used by various automotive manufacturers for qualifying ATF for use in their respective transmissions. This report deals with comparing test methods used for determining torque capacity in friction systems (shifting clutches). Three test methods were compared, the Plate Friction Test from the General Motors DEXRON®-III Specification, the Friction Durability Test from the Ford MERCON® Specification, and the Japanese Automotive Manufacturers Association Friction Test - JASO Method 348-95. Eight different fluids were evaluated. Friction parameters used in the comparison were breakaway friction, dynamic friction torque at midpoint and the end of engagement, and the ratio of end torque to midpoint torque.

This paper presents a custom integrated circuit (IC) on which circuit functions necessary for “Active Hydraulic Brake (AHB) system” are integrated, and its key component, “Current-to-Digital Converter” for solenoid current measurement. The AHB system, which realizes a seamless brake feeling for Antilock Brake System (ABS) and Regenerative Brake Cooperative Control of Hybrid Vehicle, and the custom IC are installed in the 4th-generation Prius released in 2015. In the AHB system, as linear solenoid valves are used for hydraulic brake pressure control, high-resolution and high-speed sensing of solenoid current with ripple components due to pulse width modulation (PWM) is one of the key technologies. The proposed current-to-digital converter directly samples the drain-source voltage of the sensing DMOS (double-diffused MOSFET) with an analog-to-digital (A/D) converter (ADC) on the IC, and digitizes it.

A new material recycling technology for crosslinked rubber was developed using the continuous reactive processing method. In this process of producing reclaimed rubber, breakage of crosslinking points in the crosslinked rubber occurs selectively under the controls of shear stress, reaction temperature, and internal pressure in a modular screw type reactor. Deodorization during the process has also become possible by a newly developed method. The reclaimed rubber obtained from rubber waste generated from both automobile manufacturing products and post-consumer products shows excellent mechanical properties applicable to new rubber compounds. Furthermore, an enhanced rubber recycling process for producing thermoplastic elastomer (TPE) based on rubber waste has been established. The obtained TPE exhibits highly recoverable rubber elasticity and mechanical properties comparable to commercial TPE.

A new 4.0 liter V8 engine, 1UZ-FE, has been developed for the luxury sedan, LEXUS LS400. The engine has 4 camshafts and 32 valves, and weighs only 195 kg (430 lbs) having many light alloy components and carefully designed configurations. The appropriate engine displacement and high technology adopted throughout from design to manufacturing process enable the LS400 to run powerfully with excellent fuel economy and a pleasant sounds. It develops 250HP at 5600 rpm and 260ft-lbs of torque at 4400 rpm, and its fuel economy figure, well exceeds the EPA's tax charge level of 22.5mpg. These figures have been achieved through the newest technologies applied to every part of the design, such as: Well studied intake and exhaust systems, centrally located spark plug in the TOYOTA original four-valve combustion chamber, which has a narrow valve including angle, and low friction components like aluminum alloy valve lifters and well balanced moving parts.

The protection of the environment has become a worldwide concern. To reduce the effects of engine coolant on the environment, ways to minimize the amount of coolant released into the environment were investigated. One option is to develop a super long-life coolant. The key issue in developing a long-life engine coolant is selecting an appropriate inhibitor. The inhibitor should be stable over time and completely anticorrosive. In general carboxylic acids are considered to be the class of inhibitors with the highest stability. However, various lab studies have shown the long-term use of monocarboxylic acid could form the foreign substance that causes blockage in radiators. Therefore, the mechanism leading to the formation of foreign substance was determined. A series of carboxylic acids and additives were evaluated. An optimum formulation was then determined, resulting in the development of the Super Long Life Coolant.

Many efforts have been made to understand the mechanism of whiplash injury. Recently, the cervical facet joint capsules have been focused on as a potential site of injury. An experimental approach has been taken to analyze the vertebral motion and to estimate joint capsule stretch that was thought to be a potential cause of pain. The purpose of this study is to analyze the kinematics of the cervical facet joint using a human FE model in order to better understand the injury mechanism. The Total Human Model for Safety (THUMS) was used to visually analyze the local and global kinematics of the spine. Soft tissues in the neck were newly modeled and introduced into THUMS for estimating the loading level in rear impacts. The model was first validated against human test data in the literature by comparing vertebrae motion as well as head and neck responses. Joint capsule strain was estimated from a maximum principal strain output from the elements representing the capsule tissues.

Whinning gear noise(final gear noise), one of the causes for automobile interior noise is due to the exciting force of final gear kit and as a general countermeasure for this problem, a reduction of resonance level in transfer system and better meshing of gears have been utilized. However,vibration characteristics of final gear unit have not been considered much in this case. Authors have executed impacting test on final gear unit and confirmed its vibration characteristics. Based on this fact,vibration model consisting of bearings and gears spring system was constructed to evaluate vibration characteristics of final gear unit along with the results obtained from final gear unit of front engine,rear drive passenger car.

This paper describes development of a numerical simulation method for the FMVSS 201 testing. This method considers not only deformation but also fracture of plastic materials. a simplified calculation method for predicting the load during impact of absorbing plastic materials was introduced from the numerical simulation results. By applying this simplified calculator method trial and error in development would be reduced.

Reductions of hardware costs as well as implementations of new innovative functions are the main drivers of today's automotive electronics. Indeed more and more resources are spent on adapting existing solutions to different environments. At the same time, due to the increasing number of networked components, a level of complexity has been reached which is difficult to handle using traditional development processes. The automotive industry addresses this problem through a paradigm shift from a hardware-, component-driven to a requirement- and function-driven development process, and a stringent standardization of infrastructure elements. One central standardization initiative is the AUTomotive Open System ARchitecture (AUTOSAR). AUTOSAR was founded in 2003 by major OEMs and Tier1 suppliers and now includes a large number of automotive, electronics, semiconductor, hard- and software companies.

Our two types of NOx storage-reduction (NSR) catalyst have been tested under various conditions of thermal endurance; the performance of these catalysts have been regressed to give the formulas that enable to estimate the performance after thermal endurance; and we have found the method to simplify (shorten the duration of) the thermal endurance tests and that the thermal deterioration of NSR catalysts is controlled by the worst condition of endurance (at least approximately). The regression formula for the amount of potassium that contributes to the catalyst performance (active K) after the endurance has also been obtained. These formulas predict that the amount of active K is the least for the worst condition of endurance and suggest a difference in deterioration mechanism that reflects the performance between low and high temperatures and the portion of worse deterioration (front or rear).

NO2 sources of roadside atmosphere at Matsubarabashi monitoring station in Tokyo were investigated analytically. The result showed that contribution of urban background is dominant from November to February and NO oxidation with O3 has large contribution from April to September. NO2 air quality standard will be achieved by reducing vehicle NOx emission to post-new long-term regulation level. The analytical method was verified by using our developed simulation system, which consists of micro traffic flow analyzer and CFD-based, unsteady-state diffusion with chemical reaction solver.

The dissolution and exfoliation of chromium plating specific to Russia was studied. Investigation and analysis of organic compounds in Russian soil revealed contents of highly concentrated fulvic acid. Additionally, it was found that fulvic acid, together with CaCl2 (a deicing agent), causes chromium plating corrosion. The fulvic acid generates a compound that prevents reformation of a passivation film and deteriorates the sacrificial corrosion effectiveness of nickel.

By using analytical techniques (FT-IR, TG-MS, ICP) and DFT calculations, the potassium (K) used as a storage component in NOx Catalysts can be analyzed. The results from this study show that the, K exists as K2CO3, and that the amount, molecular structure, and thermal stability of K2CO3 are different, depending on the support material (ZrO2, Al2O3, or TiO2). If the amount of K that interacts with the support to form an inactive complex oxide is decreased, the amount of K2CO3 and NOx storage is increased. The amount of the inactive K varies with the basicity of the supports. K2CO3 that exists in unstable structures on the supports can be easy to react with NOx to form the nitrate. So, the higher the quantity of unstable K2CO3, the higher the NOx storage capacity. Based on these results, a development guideline was proposed to improve the NOx storage performance.

Behavior of sprays formed by slit nozzle as well as swirl nozzles with the spray cone angle in the range of 40° ∼110 ° were studied in a constant volume N2 gas chamber. The fuels used are iso-pentane, n-heptane, benzene and gasoline. The ambient pressure and temperature were raised up to 1.0 MPa and 465 K, respectively. The injection pressure was mainly set at 8 MPa. Spray penetrates at an almost constant speed for a while after injection start and begins to decelerate at a certain point. This point was judged as breakup point, based on a momentum theory on spray motion, the observation of spray inside and the analysis of the spray front reacceleration which occurs under highly volatile condition.

In recent years, the slip lock-up mechanism has been adopted widely, because of its fuel efficiency and its ability to improve NVH. This necessitates that the automatic transmission fluid (ATF) used in automatic transmissions with slip lock-up clutches requires anti-shudder performance characteristics. The test methods used to evaluate the anti-shudder performance of an ATF can be classified roughly into two types. One is specified to measure whether a μ-V slope of the ATF is positive or negative, the other is the evaluation of the shudder occurrence in the practical vehicle. The former are μ-V property tests from MERCON® V, ATF+4®, and JASO M349-98, the latter is the vehicle test from DEXRON®-III. Additionally, in the evaluation of the μ-V property, there are two tests using the modified SAE No.2 friction machine and the modified low velocity friction apparatus (LVFA).

Ride quality is an important purchasing consideration for consumers. It is typically defined in terms of noise, vibration and harshness. These phenomena are a result of vibrations caused at the engine/powertrain and from the road surface, which are transmitted to the passenger cabin. To minimize such vibrations, rubber parts are used extensively at mounting points for the cabin, such as engine mountings and suspension bushings. The vehicle development process increasingly requires performance testing, including rubber parts using CAE, prior to prototype evaluation. This in turn requires a rubber material model that can accurately describe dynamic characteristics of rubber components, particularly frequency and amplitude dependency.

Currently, to achieve the desired design in automotive paint, absorption pigments, such as organic pigments, are used in combination with brilliant pigments (ex. aluminum or mica etc.). However, many beautiful colors exist in the world, especially in the natural world. Until now, automotive paints have not been able to replicate those colors. In this project, by first analyzing the coloring principles of the natural world, we have focused on the development of a previously non-existent coloring technology (structural color). By combining this with nanostructure control technology, we have established a radically new coloring process enabling the design of hues, chromaticity and reflection intensity. This technology has tangible results, as new pigments are available for paint formulations.

The purpose of this research is to develop an automatic shift control method that emulates an experienced driver's manual shift maneuver which enhances driving performance during sporty driving. Driver control maneuvers and vehicle behavior were observed throughout the process of braking, cornering, and accelerating out of a corner on a winding test track. Close correlations were found between driving maneuvers, longitudinal and lateral acceleration, and the selected engine speed. Based on the analysis, an index is proposed for estimating the intention of the driver to drive in a sporty manner. This index consists of the magnitude of acceleration in a friction circle and the maximum longitudinal acceleration restricted by the performance of the power train. An automatic transmission control based on the estimated driving intention was then developed to achieve the necessary and sufficient available force.

The effects of biodiesel oxidation stability on diesel fuel injection equipment (FIE) behavior were investigated using newly developed test rig and methodology. On the test rig, biodiesel blend fuels were circulated through a fuel tank and a common rail injection system. Fuel injected from typical diesel injectors was returned into the fuel tank to enhance the speed of fuel degradation. The results showed that injector deposits could be reproduced on a test rig. It was observed that injector body temperature increase accelerates the degradation of fuel and therefore gives earlier FIE failure. Fuel renewal could partially restore the injection quantity after complete failure at low injection pressure, thus showing a potential cleaning effect on injector deposits when refueling a car.