Search Results

The 4th Workshop of the Engine Combustion Network (ECN) was held September 5-6, 2015 in Kyoto, Japan. This manuscript presents a summary of the progress in experiments and modeling among ECN contributors leading to a better understanding of soot formation under the ECN “Spray A” configuration and some parametric variants. Relevant published and unpublished work from prior ECN workshops is reviewed. Experiments measuring soot particle size and morphology, soot volume fraction (fv), and transient soot mass have been conducted at various international institutions providing target data for improvements to computational models. Multiple modeling contributions using both the Reynolds Averaged Navier-Stokes (RANS) Equations approach and the Large-Eddy Simulation (LES) approach have been submitted. Among these, various chemical mechanisms, soot models, and turbulence-chemistry interaction (TCI) methodologies have been considered.

In order to comply with the increasingly restrictive limits of emissions and fuel consumption, researches are focusing on improving the efficiency of combustion engines. In this area, the aging of the injector and its effect on the injection development is not entirely analyzed. In this work, the rate of injection of a diesel injector at different stages of its lifetime is analyzed. To this end, a multi-hole piezoelectric injector was employed, comparing the injection rate measured at the beginning of its lifetime to the rate provided by the injector after aging, maintaining the same boundary conditions in both measurements. Injection pressures up to 200 MPa were used throughout the experiments. The results showed that the steady-state rate of injection was lower after the injector aged. Furthermore, the injector took a longer time to close the needle and end the injection, in comparison with the measurements done at earlier stages of its lifetime.

Compared to the gasoline engine, the diesel engine has the advantage of being more efficient and hence achieving a reduction of CO₂ levels. Unfortunately, particulate matter (PM) and nitrogen oxides (NOx) emissions from diesel engines are high. To overcome these drawbacks, several new combustion concepts have been developed, including the PCCI (Premixed Charge Compression Ignition) combustion mode. This strategy allows a simultaneous reduction of NOx and soot emissions through the reduction of local combustion temperatures and the enhancement of the fuel/air mixing. In spite of PCCI benefits, the concept is characterized by its high combustion noise levels. Currently, a promising way to improve the PCCI disadvantages is being investigated. It is related with the use of low cetane fuels such as gasoline and diesel-gasoline blends.

A commercially available fuel, E85, a blend of ~85% ethanol and ~15% gasoline, can be a viable substitute for fossil fuels in internal combustion engines in order to achieve a reduction of the greenhouse gas (GHG) emissions. Ethanol is traditionally made of biomass, which makes it a part of the food-feed-fuel competition. New processes that reuse waste products from other industries have recently been developed, making ethanol a renewable and sustainable second-generation fuel. So far, work on E85 has focused on spark ignition (SI) concepts due to high octane rating of this fuel. There is very little research on its application in CI engines. Alcohols are known for low soot particle emissions, which gives them an advantage in the NOx-soot trade-off of the compression ignition (CI) concept.

Visualization of single-hole nozzles into quiescent ambient has been used extensively in the literature to characterize spray mixing and combustion. However in-cylinder flow may have some meaningful impact on the spray evolution. In the present work, visualization of direct diesel injection spray under both non-reacting and reacting operating conditions was conducted in an optically accessible two-stroke engine equipped with a single-hole injector. Two different high-speed imaging techniques, Schlieren and UV-Light Absorption, were applied here to quantify vapor penetration for non-reacting spray. Meanwhile, Mie-scattering was used to measure the liquid length. As for reacting conditions, Schlieren and OH* chemiluminescence were simultaneously applied to obtain the spray tip penetration and flame lift-off length under the same TDC density and temperature. Additionally, PIV was used to characterize in-cylinder flow motion.

Most studies about common-rail diesel injection consider the fuel flow along the injector as isothermal. This hypothesis is arguable given the small diameter of the orifices along which the fuel flows, together with the expansions that take place across them. These phenomena may provoke variations in the fuel temperature, which in turn modify the fuel properties (i.e. viscosity, density, speed of sound…), thus influencing injector dynamics as well as the fuel atomization and mixing processes. The present investigation accounts for these effects by means of a 1D model for the fuel flow along a common-rail ballistic injector. Local variations of fuel temperature and pressure are considered by the model thanks to the implementation of the adiabatic flow hypothesis.

Computational fluid dynamics (CFD) modeling has many potentials for the design and calibration of modern and future engine concepts, including facilitating the exploration of operation conditions and casting light on the involved physical and chemical phenomena. As more attention is paid to the matching of different fuel types and combustion strategies, the use of detailed chemistry in characterizing auto-ignition, flame stabilization processes and the formation of pollutant emissions is becoming critical, yet computationally intensive. Therefore, there is much interest in using tabulated approaches to account for detailed chemistry with an affordable computational cost. In the present work, the tabulated flamelet progress variable approach (TFPV), based on flamelet assumptions, was investigated and validated by simulating constant-volume Diesel combustion with primary reference fuels - binary mixtures of n-heptane and iso-octane.

In recent decades, the importance of emerging alternative fuels has increased significantly as a solution to the problems of global warming and air pollution from energy production. In this context, ammonia (NH3) is seen as a potential option and energy vector that may be able to overcome the technical challenges associated with the use of other carbon-free fuels such as hydrogen (H2) in internal combustion engines (ICE). In this research, a numerical methodology for evaluating the impact of using ammonia as a fuel for spark-ignition ICEs has been developed. A combination of a single-cylinder and multi-cylinder numerical experiments has been performed to identify the main challenges and determine correct engine configuration. In addition, the performance of the engine has been evaluated through standard homologation driving cycles, contrasting it with other alternative propulsion configurations.

Recent studies have shown that the use of highly premixed dual fuel combustion reduces pollutant emissions and fuel consumption in CI engines. The most common strategy for dual fueling is to use two injection systems. Port fuel injection for low reactivity fuel and direct injection for high reactivity fuel. This strategy implies some severe shortcomings for its real implementation in passenger cars such as the use of two fuel tanks. In this sense, the use of a single injection system for dual fueling could solve this drawback trying to maintain pollutant and efficiency benefits. Nonetheless, when single injection system is used, the spray characteristics become an essential issue. In this work the fundamental characteristics of dual-fuel sprays with a single injection system under non-evaporating engine-like conditions are presented.

Fleet electrification has been demonstrated as a feasible solution to decarbonize the heavy-duty transportation sector. The combination of hybridization and advanced combustion concepts may provide further advantages by also introducing reductions on criteria pollutants such as nitrogen oxides and soot. In this scenario, the interplay among the different energy paths must be understood and quantified to extract the full potential of the powertrain. One of the key devices in such powertrains is the battery, which involves different aspects regarding operation, safety, and degradation. Despite this complexity, most of the models still rely on resistance-capacity models to describe the battery operation. These models may lead to unpractical results since the current flow is governed by limiters rather than physical laws. Additionally, phenomena related with battery degradation, which decreases the nominal capacity and enhances the heat generation are also not considered in this approach.

The reduction of carbon footprint of compression ignition engines for road transport makes it necessary to search for clean fuels alternative to diesel and to evaluate them under engine conditions. For this reason, in this paper, the combustion behaviour of different blends of synthetic fuels has been analyzed in an optical single cylinder engine of Medium Duty size (0,8 liters per cylinder) by means of optical techniques. The aim is to evaluate the effect of synthetic fuels, both partly or completely fossil diesel, in terms of combustion behaviours and soot formation. Therefore, different blends of oxymethylene dimethyl ether (OMEX) with diesel and neat hydrotreated vegetable oil (HVO) were studied. A conventional common rail injection system and a single injection strategy was used. In addition, special care was taken to ensure that conditions inside the engine cylinder at the injection start were as close as possible to the conditions used in previous studies.

A comparison of the flame structure for two different fuels, dodecane and oxymethylene dimethyl ether (OMEX), has been performed under condition of Spray A of the Engine Combustion Network (ECN). The experiments were carried out in a constant pressure vessel with wide optical access, at high pressure and temperature and controlled oxygen concentration. The flame structure analysis has been performed by measuring the formaldehyde and OH radical distributions using planar Laser-Induced Fluorescence (PLIF) techniques. To complement the analysis, this information was combined with that obtained with high-speed imaging of OH* chemiluminescence radiation in the UV. Formaldehyde molecules are excited with the 355-nm radiation from the third harmonic of a Nd:YAG laser, whilst OH is excited with a wavelength of 281.00-nm from a dye laser.

The dense spray region in the near-field of diesel fuel injection remains an enigma. This region is difficult to interrogate with light in the visible range and difficult to model due to the rapid interaction between liquid and gas. In particular, modeling strategies that rely on Lagrangian particle tracking of droplets have struggled in this area. To better represent the strong interaction between phases, Eulerian modeling has proven particularly useful. Models built on the concept of surface area density are advantageous where primary and secondary atomization have not yet produced droplets, but rather form more complicated liquid structures. Surface area density, a more general concept than Lagrangian droplets, naturally represents liquid structures, no matter how complex. These surface area density models, however, have not been directly experimentally validated in the past due to the inability of optical methods to elucidate such a quantity.

Knock is a major bottleneck to achieving higher thermal efficiency in spark ignition (SI) engines. The overall tendency to knock is highly dependent on fuel anti-knock quality as well as engine operating conditions. It is, therefore, critical to gain a better understanding of fuel-engine interactions in order to develop robust knock mitigation strategies. In the present work, a numerical model based on three-dimensional (3-D) computational fluid dynamics (CFD) was developed to capture knock in a Cooperative Fuel Research (CFR) engine. For combustion modeling, a hybrid approach incorporating the G-equation model to track turbulent flame propagation, and a homogeneous reactor multi-zone model to predict end-gas auto-ignition ahead of the flame front and post-flame oxidation in the burned zone, was employed.

The increasingly stringent emissions regulations together with the demand of highly efficient vehicles from the customers, lead to rapid developments of distinct powertrain solutions, especially when the electrification is present in a certain degree. The combination of electric machines with conventional powertrains diversifies the powertrain architectures and brings the opportunity to save energy in greater extents. On the other hand, alternative combustion modes as reactivity controlled compression ignition (RCCI) have shown to provide simultaneous ultra-low NOx and soot emissions with similar or better thermal efficiency than conventional diesel combustion (CDC). In addition, it is necessary to introduce more renewable fuels as ethanol to reduce the total CO2 emitted to the atmosphere, also called well-to-wheel (WTW) emission, in the transport sector.

Several new combustion concepts have been developed during last decade with the aim of reducing pollutant emissions. Specifically, these strategies allow a simultaneous reduction of NOx and soot emissions by reducing the local combustion temperatures, enhancing the fuel/air mixing (PCCI, HCCI…). In spite of their benefits, these concepts present difficulties controlling the appropriate combustion phasing as well as high knocking levels and therefore, their operating range is reduced to low-medium loads. In this work gasoline is considered as a fuel in order to improve combustion strategies based on fully or partially premixed combustion in CI engines. Its use provides more flexibility to achieve lean and low combustion temperature, however the concept has demonstrated difficulty under light load conditions using gasoline with ON up to 95.

Methanol is currently being evaluated as a promising alternative fuel for internal combustion engines, due to being attainable by carbon neutral or negative pathways (renewable energy and carbon capture technology). The low ignitability of methanol has made it attractive mostly as a fuel for spark ignition engines, however the low sooting properties of the fuel could potentially reduce the NOx-soot tradeoff present in compression ignition engines. In this work, using a 4-cylinder engine with compression ratio modified from 16:1 to 19:1, methanol combustion is evaluated under five operating conditions in terms of fuel consumption, criteria pollutants, CO2 emissions and engine efficiency in addition to the qualitative assessment of the combustion stability. It was found that combustion is stable at medium to high loads, with medium load NOx emissions levels at least 30% lower than the original diesel engine and comparable emissions at maximum load conditions.

De-fossilization is an increasingly important trend in the energy sector. In the transport sector the de-fossilization efforts have been centered in promoting the electrification of vehicles, nonetheless other pathways, like the use of carbon neutral or carbon-offsetting fuels under current vehicle fleets, are also worth considering. Low-carbon fuels (LCF) can be synthetized from sources that can take advantage of the carbon already present in the atmosphere (either by technologies like direct carbon capture or biological processes like photosynthesis in biofuels) and use energy from renewable sources for the necessary industrial processes. Although, LCFs can be compared to fossil fuels as energy sources for internal combustion engines, their composition is not the same and their properties can modify the engine combustion and emissions.

The influence of pressure and temperature on some of the important thermodynamic properties of diesel fuels has been assessed for a set of fuels. The study focuses on the experimental determination of the speed of sound, density and compressibility (via the bulk modulus) of these fuels by means of a method that is thoroughly described in this paper. The setup makes use of a common-rail injection system in order to transmit a pressure wave through a high-pressure line and measure the time it takes for the wave to travel a given distance. Measurements have been performed in a wide range of pressures (from atmospheric pressure up to 200 MPa) and temperatures (from 303 to 353 K), in order to generate a fuel properties database for modelers on the field of injection systems for diesel engines to incorporate to their simulations.

Economy decarbonization will be one of the main goals for the following years. Research efforts are being focused on reducing carbon-based emissions, by increasing the efficiency of the transport power plants while developing new fuel production methods that reduce the environmental footprint of the refinement process. Consequently, the depletion of conventional fuels derived from petroleum with high carbon content, such as gasoline and diesel, motivated the development of propulsive alternatives for the transportation sector. In this paradigm, methane (CH4) fuel appears as a mid-term solution due to its low carbon content, if compared with traditional fuels, and the low CO2 emissions during its production from renewable sources. However, the intrinsic properties of methane compromise the combustion process, subsequently increasing the emission of CO2.