Search Results

The emissions and efficiency of modern internal combustion engines need to be improved to reduce their environmental impact. Many strategies to address this (e.g., alternative fuels, exhaust gas aftertreatment, novel injection systems, etc.) require engine calibrations to be modified, involving extensive experimental data collection. A new approach to modeling and data collection is proposed to expedite the development of these new technologies and to reduce their upfront cost. This work evaluates a Gaussian Process Regression, Artificial Neural Network and Bayesian Optimization based strategy for the efficient development of machine learning models, intended for engine optimization and calibration. The objective of this method is to minimize the size of the required experimental data set and reduce the associated data collection cost for engine modeling.

In this paper a study of the squish-generated charge motion in the combustion chamber of a natural gas engine is reported. A combination of both numerical simulations and actual engine tests was used to correlate the turbulence level at the spark plug location with performance and cylinder pressure data for three different chamber configurations. The higher-turbulence combustion chamber showed an average 1.5% reduction in brake specific fuel consumption in comparison with the lower turbulence level combustion chambers. The emission levels from the high-turbulence case were, however, generally higher than those from the lower-turbulence combustion chambers.

The fuel economy and emissions performance of a Diesel engine is strongly influenced by the fuel injection process. This paper presents early results of an experimental investigation into diesel spray development carried out in a novel in-house developed optical pressure chamber capable of operating at pressure up to 50 bar and temperatures up to 900 K. The spatial evolution of a diesel spray tends to experience many transitory macroscopic phenomena that directly influence the mixing process. These phenomena are not considered highly reproducible and are extremely short lived, hence recording and understanding these transient effects is difficult. In this study, high-speed backlight-illuminated imaging has been employed in order to capture the transient dynamics of a short signal duration diesel spray injected into incremental back pressures and temperatures reaching a maximum of 10 bar and 473 K respectively.

In direct-injection engines, combustion and emission formation is strongly affected by injection quality. Injection quality is related to mass-flow rate shape, momentum rate shape, stability of pulses as well as mechanical and hydraulic delays associated with fuel injection. Finding these injector characteristics aids the interpretation of engine experiments and design of new injection strategies. The goal of this study is to investigate the rate of momentum for the single and post injections for high-pressure direct-injection natural gas injectors. The momentum measurement method has been used before to study momentum rate of injection for single and split injections for diesel sprays. In this paper, a method of momentum measurement for gas injections is developed in order to present transient momentum rate shape during injection timing. In this method, a gas jet impinges perpendicularly on a pressure transducer surface.

Flash-boiling of sprays may occur when a superheated liquid is discharged into an ambient environment with lower pressure than its saturation pressure. Such conditions normally exist in direct-injection spark-ignition engines operating at low in-cylinder pressures and/or high fuel temperatures. The addition of novel high volatile additives/fuels may also promote flash-boiling. Fuel flashing plays a significant role in mixture formation by promoting faster breakup and higher fuel evaporation rates compared to non-flashing conditions. Therefore, fundamental understanding of the characteristics of flashing sprays is necessary for the development of more efficient mixture formation. The present computational work focuses on modelling flash-boiling of n-Pentane and iso-Octane sprays using a Lagrangian particle tracking technique.

An experimental investigation of the autoignition and emission characteristics of transient turbulent gaseous fuel jets in heated and compressed air was conducted in a shock tube facility. Experiments were performed at an initial pressure of 30 bar with initial oxidizer temperatures ranging from 1200 to 1400 K, injection pressures ranging from 60 to 150 bar, and injection durations ranging from 1.0 to 2.5 ms. Methane and 90.0% methane/10.0% ethane blend were used as fuel. Under the operating conditions studied, increasing temperature resulted in a significant decrease in autoignition delay time. Increasing the injection pressure decreased ignition delay as well. The downstream location of the ignition kernel relative to the jet penetration distance was found to be in the range, 0.4

This paper addresses the need for fundamental understanding of the mechanisms of fuel spray formation and mixture preparation in direct injection spark ignition (DISI) engines. Fuel injection systems for DISI engines undergo rapid developments in their design and performance, therefore, their spray breakup mechanisms in the physical conditions encountered in DISI engines over a range of operating conditions and injection strategies require continuous attention. In this context, there are sparse data in the literature on spray formation differences between conventionally drilled injectors by spark erosion and latest Laser-drilled injector nozzles. A comparison was first carried out between the holes of spark-eroded and Laser-drilled injectors of same nominal type by analysing their in-nozzle geometry and surface roughness under an electron microscope.

Recent pressures on vehicle manufacturers to reduce their average fleet levels of CO2 emissions have resulted in an increased drive to improve fuel economy and enable use of fuels developed from renewable sources that can achieve a net reduction in the CO2 output of each vehicle. The most popular choice for spark-ignition engines has been the blending of ethanol with gasoline, where the ethanol is derived either from agricultural or cellulosic sources such as sugar cane, corn or decomposed plant matter. However, other fuels, such as butanol, have also arisen as potential candidates due to their similarities to gasoline, e.g. higher energy density than ethanol. To extract the maximum benefits from these new fuels through optimized engine design and calibration, an understanding of the behaviour of these fuels in modern engines is necessary.

This paper presents a study of the combustion mechanism of hydrous and anhydrous ethanol in comparison to iso-octane and gasoline fuels in a single-cylinder spark-ignition research engine operated at 1000 rpm with 0.5 bar intake plenum pressure. The engine was equipped with optical access and tests were conducted with both Port Fuel Injection (PFI) and Direct Injection (DI) mixture preparation methods; all tests were conducted at stoichiometric conditions. The results showed that all alcohol fuels, both hydrous and anhydrous, burned faster than iso-octane and gasoline for both PFI and DI operation. The rate of combustion and peak cylinder pressure decreased with water content in ethanol for both modes of mixture preparation. Flame growth data were obtained by high-speed chemiluminescence imaging. These showed similar trends to the mass fraction burned curves obtained by in-cylinder heat release analysis for PFI operation; however, the trend with DI was not as consistent as with PFI.

An arrangement of port - injected, stratified-charge, 4 - valve SI engine is proposed, in which fuel is injected in a thin column from an injector which is angled so that the fuel is deflected by one of the inlet valves onto the combustion chamber surface, at a position close to the central spark plug. The injection takes place towards the end of the induction stroke, and the injector is mounted to the side of one of the intake ports. The second intake port is deactivated at part load to establish an axial swirling motion to stabilise the fuel evaporating from the warm combustion chamber surface. Testing has been performed on a single - cylinder research engine to assess the extent of the stratification by measuring pre - flame hydrocarbon concentrations at various positions around the combustion chamber.

This experimental work was concerned with the combination of internal EGR with an early inlet valve closure strategy for improved part-load fuel economy. The experiments were performed in a new spark-ignited thermodynamic single cylinder research engine, equipped with a mechanical fully variable valvetrain on both the inlet and exhaust. During unthrottled operation at constant engine speed and load, increasing the mass of trapped residual allowed increased valve duration and lift to be used. In turn, this enabled further small improvements in gas exchange efficiency, thermal efficiency and hence indicated fuel consumption. Such effects were quantified under both port and homogeneous central direct fuel injection conditions. Shrouding of the inlet ports as a potential method to increase in-cylinder gas velocities has also been considered.

Combustion of natural gas in a spark-ignition engine has been studied experimentally in a single-cylinder research engine, as well as analytically with the aid of a thick-flame burning simulation. Cylinder pressure measurements, averaged over 100 cycles, have been used in determining average combustion progress an cyclic variations in early burning time. The dependence of early (0-10%) and main (10-90%) combustion durations on load, speed, equivalence ratio, and chamber geometry (disc vs. bathtub) have been determined. A combustion simulation based on laminar burning at the Taylor microscale, with rapid flame propagation in regions of concentrated vorticity, has been used to estimate burning zone thickness, flame propagation rate, and the amplitude of cyclic variations in the early combustion period. The simulation provides a good representation of combustion over a wide range of operating conditions.

This paper examines the combustion and emissions produced using a prototype fuel injector nozzle for pilot-ignited direct-injection natural gas engines. In the new geometry, 7 individual equally-spaced gas injection holes were replaced by 7 pairs of closely-aligned holes (“paired-hole nozzle”). The paired-hole nozzle was intended to reduce particulate formation by increasing air entrainment due to jet interaction. Tests were performed on a single-cylinder research engine at different speeds and loads, and over a range of fuel injection and air handling conditions. Emissions were compared to those resulting from a reference injector with equally spaced holes (“single-hole nozzle”). Contrary to expectations, the CO and PM emissions were 3 to 10 times higher when using the paired-hole nozzles. Despite the large differences in emissions, the relative change in emissions in response to parametric changes was remarkably similar for single-hole and paired-hole nozzles.

For a spark-ignition engine, the parasitic loss suffered as a result of conventional throttling has long been recognised as a major reason for poor part-load fuel efficiency. While lean, stratified charge, operation addresses this issue, exhaust gas aftertreatment is more challenging compared with homogeneous operation and three-way catalyst after-treatment. This paper adopts a different approach: homogeneous charge direct injection (DI) operation with variable valve actuations which reduce throttling losses. In particular, low-lift and early inlet valve closing (EIVC) strategies are investigated. Results from a thermodynamic single cylinder engine are presented that quantify the effect of two low-lift camshafts and one standard high-lift camshaft operating EIVC strategies at four engine running conditions; both, two- and single-inlet valve operation were investigated. Tests were conducted for both port and DI fuelling, under stoichiometric conditions.

Hydrogen has been largely proposed as a possible fuel for internal combustion engines. The main advantage of burning hydrogen is the absence of carbon-based tailpipe emissions. Hydrogen's wide flammability also offers the advantage of very lean combustion and higher engine efficiency than conventional carbon-based fuels. In order to avoid abnormal combustion modes like pre-ignition and backfiring, as well as air displacement from hydrogen's large injected volume per cycle, direct injection of hydrogen after intake valve closure is the preferred mixture preparation method for hydrogen engines. The current work focused on computational studies of hydrogen injection and mixture formation for direct-injection spark-ignition engines. Hydrogen conditions at the injector's nozzle exit are typically sonic.

Conditional source-term estimation (CSE) is a novel chemical closure method for the simulation of turbulent combustion. It is less restrictive than flamelet-based models since no assumption is made regarding the combustion regime of the flame; moreover, it is computationally cheaper than conventional conditional moment closure (CMC) models. To date, CSE has only been applied for simulating canonical laboratory flames such as steady Bunsen burner flames. Industry-relevant problems pose the challenge of accurately modelling a transient ignition process in addition to involving complex domaingeometries. In this work, CSE is used to model combustion in a homogeneous-charge natural gas fuelled SI engine. The single cylinder Ricardo Hydra research engine studied here has a relatively simple chamber geometry which is represented by an axisymmetric mesh; moving-mesh simulations are conducted using the open-source computational fluid dynamics software, OpenFOAM.

Low speed pre-ignition (LSPI) is a limiting phenomenon for several of the technologies being pursued as part of the low carbon agenda. To achieve maximum power density and efficiency engines are being downsized and turbocharged, while Direct- injection technologies are becoming ever more prominent. All changes that increase the propensity of LSPI. The low speed-high load operation envelope is limited due to LSPI. Hydrogen engines are also being explored, however, with such a low minimum enthalpy of ignition, LSPI is a major limitation to thermal efficiency. Several techniques are utilized in this study to investigate physical and physio-chemical aspects of lubricant initiated LSPI. Where possible attempts have been to validate methodologies or directional alignment with published data. The basis of the methodologies used is a validated 1D predictive combustion model of a single cylinder GTDI engine, that was used to provide simulation boundary conditions.

A key objective of this research was to develop an interface device to enable visualization of in-cylinder events within a production SI engine operating at normal speeds and loads, without the need for engine modifications. The device was designed to utilize the existing spark plug hole and to be capable of providing in-cylinder illumination, image transmission and a source of ignition. This technical paper presents the results of the initial evaluation of the device. The evaluation of the durability of the device, in terms of its ability to operate as a spark plug and its permissible operating range is presented. In addition, images of events in the cylinder captured using the device are provided.

Development of new fuels and engine combustion strategies for future ultra-low emission engines requires a greater level of insight into the process of emissions formation than is afforded by the approach of engine exhaust measurement. The paper describes the development of an in-cylinder gas sampling system consisting of a fast-acting, percussion-based, poppet-type sampling valve, and a heated dilution tunnel; and the deployment of the system in a single cylinder engine. A control system was also developed for the sampling valve to allow gas samples to be extracted from the engine cylinder during combustion, at any desired crank angle in the engine cycle, while the valve motion was continuously monitored using a proximity sensor. The gas sampling system was utilised on a direct injection diesel engine co-combusting a range of hydrogen-diesel fuel and methane-diesel fuel mixtures.

An air-assisted fuel vaporiser (AAFV), designed to replace the conventional fuelling system has been tested on a 3.0-litre development engine under simulated cold-Start conditions. Providing the cold engine with pre-vaporised fuel removed the need for an enriched mixture during start-up. Comparisons between the AAFV and standard fuelling systems were performed. Engine-out hydrocarbon (HC) exhaust emissions were measured during cold-start and the ensuing two minutes. Fuel spray characterisation was also conducted using a steady flow test rig designed to mimic inlet port conditions of air flow and manifold pressure over a wide range of engine operation.