Search Results

This paper describes the simulation model of a backhoe excavator. The model uses a prescribed motion cycle and the objective of the program is to determine the power requirements for each of the cylinders as well as the total engine power requirement. Most computer simulations are developed by expressing the differential equations of motion for the system being studied. The known force inputs to the system are applied and the time response of the system is then obtained by numerically integrating the governing differential equations. This paper on the other hand develops the reverse of this. Utilizing a prescribed geometry and trajectory cycle for a linkage system as the input, the program solves for the types of force inputs that are required to achieve that trajectory. With the time dependence of the trajectory known, the total power required and the power required of each cylinder is also evaluated. A typical excavator linkage is shown in Fig. 1.

A traditional method of controlling evaporator superheat in a vapor compression air conditioning system is the thermostatic expansion valve (TXV). Such systems are often used in automotive applications. The TXV depends on superheat to adjust the valve opening. Unfortunately, any amount of superheat causes that evaporator to operate at reduced capacity due to dramatically lower heat transfer coefficients in the superheated region. In addition, oil circulation back to the compressor is impeded. The cold lubricant almost devoid of dissolved refrigerant is quite viscous and clings to the evaporator walls. A system that could control an air conditioner to operate with no superheat would either decrease the size of its existing evaporator while maintaining the same capacity, or potentially increase its capacity with its original evaporator. Also, oil circulation back to the compressor would be improved.

In this work, an efficient and unified combustion model is introduced to simulate the flame propagation, diffusion-controlled combustion, and chemically-driven ignition in both SI and CI engine operation. The unified model is constructed upon a G-equation model which addresses the premixed flame propagation. The concept of the Livengood-Wu integral is used with tabulated ignition delay data to account for the chemical kinetics which is responsible for the spontaneous ignition of fuel-air mixture. A set of rigorously defined operations are used to couple the evolution of the G scalar field and the Livengood-Wu integral. The diffusion-controlled combustion is simulated equivalent to applying the Burke-Schumann limit. The combined model is tested in the simulation of the premixed SI combustion in a constant volume chamber, as well as the CI combustion in a conventional small bore diesel engine.

This paper discusses an advanced computer-based process simulation model to predict cutting forces and surface error (also referred to as the lack of cylindricity) for the cylinder boring process. The model takes into consideration several enhanced features including dual and multiple-cylinder boring, back-boring, boring in the presence of windows/cavities, etc.. The model makes use of a Finite Element product model and the cutting force process model to generate a surface error profile at any axial level in the cylinder bore. A design of experiment approach is employed to study the influence of various process variables on bore surface error. The enhanced process simulation model may be used as a valuable tool in enhancing the simultaneous engineering of products and manufacturing processes.

The influence of different combustion chamber configuration, intake temperature, and coolant temperature on HCCI combustion processes were investigated in a single-cylinder optical engine. Two-dimensional images of the chemiluminescence were captured using an intensified CCD camera in order to understand the spatial distribution of the combustion. N-heptane was used as the test fuel. Three combustion chamber geometries with different squish lip, salient, orthogonal, reentrant shape, referred as V-type, H-type, and A-type respectively, were used in this study. Intake temperature was set to 65°C and 95°C, while coolant temperature was set to 85°C. The experimental data consisting of the in-cylinder pressure, heat release rate, chemiluminescence images all indicated that the different combustion chamber geometries result in different turbulence intensity in the combustion chamber, and thus affect the auto-ignition timing, chemiluminescence intensity, and combustion processes.

The development of automated guidance for agricultural tractors has addressed several basic and applied issues of agricultural equipment automation. Basic analyses have included the dynamics of steering systems and posture sensors for guidance. Applied issues have evaluated the potential of several commercial sensing systems and a commercial mechanical guidance system. A research platform has been developed based on a Case 7220 Magnum1 2-wheel drive agricultural tractor. An electrohydraulic steering system was used and characterized in support of automated guidance control. Posture sensing methods were developed using GPS, geomagnetic direction sensors (GDS), inertial, and machine vision sensing systems. Sensor fusion of GPS-inertial-machine vision and GPS-GDS-machine vision provided the most flexible and accurate guidance and capable for operation under dynamically changing field conditions.

Cylinder head combustion chamber and piston temperatures and heat fluxes were measured in a 2.2 L 4 cylinder spark ignition engine. Measurements for the combustion chamber were made at wide open throttle conditions, 1400 rpm to 5000 rpm at 600 rpm increments, additional measurements were made on the combustion chamber at part throttle conditions at 3200 RPM. Piston temperature and heat flux measurements were made at WOT conditions from 1400 to 3200 RPM in 600 RPM increments. Average combustion chamber surface temperatures ranged from 130 deg. C to 248 deg. C, while peak combustion chamber surface temperatures ranged from 142 deg. C to 258 deg. C for WOT conditions. Peak heat flus at the surface for WOT conditions in the combustion chamber ranged from 1.2 MW/m2to 5.0 MW/m2. Central region heat fluxes were 2.3 to 2.8 times greater than those in the end gas regions of the combustion chamber.

The operation of a small bore high speed direct injection (HSDI) engine with a MVCO injector is simulated by the KIVA 3V code, developed by Los Alamos National Laboratory. The MVCO injector extends the range of injection timings over conventional injectors and it extra flexibility in designing injection schemes. Combustion from very early injection is observed with MVCO injections but not with conventional injection. This improves the fuel economy of the engine in terms of lower ISFC. Even better efficiency can be achieved by using biodiesel, which may be due to extra oxygen in the fuel improving the combustion process. Biodiesel sees a longer ignition delay for the initial injection. It also exhibits a faster burning rate and shorter combustion duration. Biodiesel also lowered both NOx and soot emissions. This is consistent with the general observation for soot emissions.

The availability and low price of personal computers with suitable interface equipment has made it practical to use such a system for cylinder pressure data acquisition. With this objective, procedures have been developed to measure and record cylinder pressure on an individual crank angle basis and obtain an average cylinder pressure trace using an Apple II Plus personal computer. These procedures as well as methods for checking the quality of cylinder pressure data are described. A simplified heat release analysis technique for an approximate first look at the data quality is presented. Comparisons are made between the result of this analysis, the Krieger-Borman heat release analysis which uses complete chemical equilibrium. The comparison is made to show the suitability of the simplified analysis in judging the quality of the pressure data.

Single-laser-shot measurements of the fuel/air ratio in the cylinder of a motored direct-injection natural gas (DING) engine were obtained using a dual-pump coherent anti-Stokes Raman scattering (CARS) technique capable of simultaneously probing N2 and CH4. The DING engine was modified for optical access and CARS was used to probe the region near the glow plug. Measurements were acquired at eight different probe volume locations with one crank angle degree resolution for injections starting at 30° and 20° BTDC. The CARS data clearly show the arrival of the fuel jet at the probe volume and, from traversing the probe volume, the location of the centerlines of two fuel jets in the vicinity of the glow plug. The CARS measurements also show large fluctuations in fuel concentration on a shot-to-shot basis indicating the presence of large-scale mixing structures within the fuel jets.

Basket motion of a cotton picker during the unloading cycle can produce unstable conditions that result in overturning the machine. The potential for overturning increases while operating the machine on a side slope with the basket dumping on the down-hill side. In this paper the writers investigate the influence of tire ballast, wheel weights and operator control of the hydraulic cylinder on the dynamic stability of the machine during the unloading cycle while operating on a side slope. Operator control at the beginning of the unloading cycle and near the end of the cylinder stroke promotes stable operation of the machine on a side slope.

The transporting of live cattle involves the use of Class 8 tractors and livestock semi-trailers for transportation from farms and feedlots to processing plants. This travel may include unimproved roads, local streets, two lane highways, as well as interstate highways. Typically, cattle are compartmentalized in a “double deck” fashion as it provides utility and comports with size and weight limits for commercial Class 8 vehicles. Concern has been expressed for the effect of cattle movement upon the dynamic performance of the loaded Class 8 tractor-livestock trailer assembly. Loading guidelines exist for cattle that attempt to prevent injury or debilitation during transit, and literature exists on the orientation and some kinematics of loaded cattle. Considerable literature exists on the effect of liquid slosh in tankers and swinging beef carcasses suspended from hooks in refrigerated van trailers on the dynamic response and roll stability of those vehicles.

The detailed mechanisms by which oxygenated diesel fuels reduce engine-out soot emissions are not well understood. The literature contains conflicting results as to whether a fuel's overall oxygen content is the only important parameter in determining its soot-reduction potential, or if oxygenate molecular structure or other variables also play significant roles. To begin to resolve this controversy, experiments were conducted at a 1200-rpm, moderate-load operating condition using a modern-technology, 4-stroke, heavy-duty DI diesel engine with optical access. Images of broadband natural luminosity (i.e., light emission without spectral filtering) from the combustion chamber, coupled with heat-release and efficiency analyses, are presented for three test-fuels. One test-fuel (denoted GE80) was oxygenated with tri-propylene glycol methyl ether; the second (denoted BM88) was oxygenated with di-butyl maleate. The overall oxygen contents of these two fuels were matched at 26% by weight.

Machine operators rely on intuition and experience to evaluate vehicle performance. As we increasingly turn to automation, it is important to automatically evaluate sensor data and system performance. Fuzzy logic allows us to take advantage of domain knowledge to evaluate data and to describe a system linguistically. In this paper, two automated fuzzy evaluation systems are described. In the first, a fuzzy quality module evaluates output from a simulated noisy sensor. In the second system, a fuzzy quality module evaluates the output from a machine vision system. Results from both systems indicate that fuzzy logic was able to accurately categorize the output in support of machinery decision making for automated control.

The presence and distribution of liquid fuel within an engine cylinder at cold start may adversely affect the hydrocarbon emissions from port-injected, spark ignition engines. Therefore, high speed videos of the liquid fuel entry into the cylinder of an optical engine were recorded in order to assess the effect of various engine operating parameters on the amount of liquid fuel inducted into the cylinder, the sizes of liquid drops present and the distribution of the fuel within the cylinder. A 2.5L, V-6, port-injected, spark ignition engine was modified so that optical access is available throughout the entire volume of one of the cylinders. A fused silica cylinder is sandwiched between the separated block and head of the engine and a “Bowditch-type” piston extension is mounted to the production piston. The Bowditch piston has a fused silica crown so that visualization is possible through the top of the piston as well as through the transparent cylinder.

The use of substances other than petroleum based fuels for power sources is not a new concept. Prior to the advent of petroleum fueled vehicles numerous other substances were used to create mobile sources of power. As the world's petroleum supply dwindles, alternative fuel sources are sought after to replace petroleum fuels. Many industries are particularly interested in the development of renewable fuel sources, or biologically derived fuel sources, which includes ethanol. The use of No. 2 diesel as well as many alternative fuels in compression ignition engines result in injector coking. Injector coking can severely limit engine performance by limiting the amount of fuel delivered to the combustion chamber and altering the spray pattern. Injector tip coking is also one of the most sensitive measures of diesel fuel quality [1]. A machine vision system was implemented to quantify injector coking accumulation when a compression ignition engine was fueled with oxydiesel.

Homogeneous Charge Compression Ignition (HCCI) combustion employing single main injection strategies in an optically accessible single cylinder small-bore High-Speed Direct Injection (HSDI) diesel engine equipped with a Bosch common-rail electronic fuel injection system was investigated in this work. In-cylinder pressure was taken to analyze the heat release process for different operating parameters. The whole cycle combustion process was visualized with a high-speed digital camera by imaging natural flame luminosity. The flame images taken from both the bottom of the optical piston and the side window were taken simultaneously using one camera to show three dimensional combustion events within the combustion chamber. The engine was operated under similar Top Dead Center (TDC) conditions to metal engines. Because the optical piston has a realistic geometry, the results presented are close to real metal engine operations.

The formation of fuel film in the combustion cylinder affects the mixing process of the air and the fuel, and the process of the combustion propagation in engines. Some models of film evaporation have been developed to predict the evaporation behavior of the film, but rarely experimental results have been produced, especially when the temperature is high. In this study, the evaporation behavior of the film of different species of oil and their blends at different temperature are observed. The 45 μL films of isooctane, 1-propanol, 1-butanol, 1-pentanol, and their blends were placed on a quartz glass substrate in the closed temperature-controlled chamber. The shape change of the film during evaporation was monitored by a high-speed camera through the window of the chamber. First, the binary blends film of isooctane and one of the other three oils were evaporated at 30 °C, 50 °C, 70 °C and 90 °C.

A direct-injection natural gas (DING) engine was modified for optical access to allow the use of laser diagnostic techniques to measure species concentrations and temperatures within the cylinder. The injection and mixing processes were examined using planar laser-induced fluorescence (PLIF) of acetone-seeded natural gas to obtain qualitative maps of the fuel/air ratio. Initial acetone PLIF images were acquired in a quiescent combustion chamber with the piston locked in a position corresponding to 90° BTDC. A series of single shot images acquired in 0.1 ms intervals was used to measure the progression of one of the fuel jets across the cylinder. Cylinder pressures as high as 2 MPa were used to match the in-cylinder density during injection in a firing engine. Subsequent images were acquired in a motoring engine at 600 rpm with injections starting at 30, 20, and 15° BTDC in 0.5 crank angle degree increments.

Understanding lubrication failures at the shoe/swashplate contact of automotive swashplate compressors will greatly enhance the reliability of the air conditioning system. Maintaining proper lubrication is not always possible during transient conditions. Therefore, a method for detection of lubricant loss is of great interest to the automotive industry. Three methods for detecting lubrication loss were examined: contact resistance, acoustic emission, and dynamic pressure oscillations. A mobile air conditioning test stand capable of recording many system parameters was used. Oil return to the compressor was monitored using an oil separator and a refrigerant/oil concentration sensor. Data were taken during steady oil return rates and after oil shut off. The electrical contact resistance between the shoe and swashplate was used to indicate changes in the lubrication conditions at this critical interface. Measurements were taken at two oil return rates during steady oil return tests.