Search Results

Due to the variability of real traffic conditions for vehicle testing, real-world vehicle performance estimation using simulation method become vital. Especially for heavy duty vehicles (e.g. 40 t trucks), which are used for international freight transport, real-world tests are difficult, complex and expensive. Vehicle simulations use mathematical methods or commercial software, which take given driving cycles as inputs. However, the road situations in real driving are different from the driving cycles, whose speed profiles are obtained under specific conditions. In this paper, a real-world vehicle performance estimation method using simulation was proposed, also it took traffic and real road situations into consideration, which made it possible to investigate the performance of vehicles operating on any roads and traffic conditions. The proposed approach is applicable to all kind of road vehicles, e.g. trucks, buses, etc. In the method, the real-road network includes road elevation.

A 2-D simulation of fluid dynamic and chemistry interaction following end gas autoignition has demonstrated three distinct modes of reaction, dependent upon the temperature gradient about an exothermic centre. All three modes (deflagration, developing detonation and thermal explosion) can contribute to knock; the developing detonation case, associated with intermediate temperature gradient, has been identified as the more damaging. The simulation code (LUMAD) has been used in a systematic parametric study designed to separate the complex interacting events which can lead to mixed modes in real engines. A most significant finding related to the sequential autoignition of multiple exothermic centres.

Different driving test cycles, the Leeds-West Park (LWP) loop and the Leeds-High Park (LHP) or HPL-A and B (Leeds-Hyde Park Loop-A or B, hereafter referred as HPL-A or B cycle) loop were selected for this urban intersection research and results are presented in this study. Different emissions-compliant petrol passenger cars (EURO 1, 2, 3 and 4) were compared for their real-world emissions. A reasonable distance of steady state speed was needed and for the analysis made in this paper were chosen vehicle speeds at ~20, ~30 and ~40 km/h. Specific spot of periods of driving at the speeds mentioned above were identified, then the starting and ending point was found and the total emissions in g for that period divided by the distance was calculated. A typical urban driving cycle including a loop and a section of straight road was used for the comparison test as it was similar to the legislative ECE15 urban driving cycle.

The tailpipe exhaust emissions were measured under real world urban driving conditions by using a EURO4 emissions compliant SI car equipped with an on-board heated FTIR for speciated gaseous emission measurements, a differential GPS for travel profiles, thermocouples for temperatures, and a MAX fuel meter for transient fuel consumption. Emissions species were measured at 0.5 Hz. The tests were designed to enable cold start to occur into congested traffic, typical of the situation of people living alongside congested roads into a large city. The cold start was monitored through temperature measurements of the TWC front and rear face temperatures and lubricating oil temperatures. The emissions are presented to the end of the cold start, defined when the downstream TWC face temperature is hotter than the front face which occurred at ∼350-400oC. Journeys at various times of the day were conducted to investigate traffic flow impacts on the cold start.

Small diesel engines are a common primer for micro and mini-grid systems, which can supply affordable electricity to rural and remote areas, especially in developing countries. These diesel generators have no exhaust after-treatment system thus exhaust emissions are high. This paper investigates the potential of introducing simulated synthetic gas (syngas) to diesel in a small diesel engine to explore the opportunities of widening fuel choices and reducing emissions using a 5.7kW single cylinder direct injection diesel generator engine. Three different simulated syngas blends (with varying hydrogen content) were prepared to represent the typical syngas compositions produced from downdraft gasification and were injected into the air inlet. In-cylinder pressure, ignition delay, premixed combustion, combustion stability, specific energy consumption (SEC), and gaseous and particle emissions were measured at various power settings and mixing ratios.

Torsional motion of a truck driveline system is coupled with other motions of its components. In this paper, a comprehensive model of the truck driveline and body for vibration analysis was developed. Coupling of the torsional vibration of the truck driveline system with the body fore-aft and vertical vibrations was investigated. A mathematical model, including the torsional vibration of the driveline system and the whole body vibrations of the truck, was constructed. The driveline system was modelled as a set of inertia discs linked together by massless springs and the tyre was represented as having massless circumferential band which is elastically connected to the carcass with the bands being subject to longitudinal forces at the road surface. System behaviour at steady and transient runs was developed.

This paper will present a method of estimating tyre friction force using an extended Kalman filter (EKF). A review of current and proposed methods for tyre force estimation from the literature will be given. The EKF developed will estimate vehicle motions and tyre forces as state estimates from a noisy measurement set. The tyre forces will be compared to those from a high order vehicle model with non-linear tyres, which is subjected to the same tests as the measured vehicle, in order to validate the estimated forces. The robustness of the estimator to noise and input errors will be tested. The ultimate aim of this work is to provide estimates of tyre forces to a controller such as ABS or TCS.

In order to improve energy supply diversity and reduce carbon dioxide emissions, sustainable bio-fuels are strongly supported by EU and other governments in the world. While the feedstock of biofuels has caused a debate on the issue of sustainability, the used cooking oil (UCO) has become a preferred feedstock for biodiesel manufacturers. However, intensive energy consumption in the trans-esterification process during the UCO biodiesel production has significantly compromised the carbon reduction potentials and increased the cost of the UCO biodiesel. Moreover, the yield of biodiesel is only ∼90% and the remaining ∼10% feedstock is wasted as by-product glycerol. Direct use of UCO in diesel engines is a way to maximize its carbon saving potentials.

Persisting concerns regarding ride comfort, directional stability and more recently road damage have caused the manufacturers of commercial vehicles to consider controllable suspension systems. An electronically controllable adaptive suspension that comprises a variable spring rate system, switchable damping and load levelling is proposed as a cost-effective solution. This paper describes the aforementioned system and provides an outline of the design scheme for a prototype system; practical issues such as system configuration/detail, control system requirements, etc., are discussed. The system is evaluated analytically and both ride and handling modes are examined. In conclusion, performance capabilities are defined and cost-benefit issues addressed.

A non-linear contact analysis of a leading-trailing shoe drum brake, using the finite element method, is presented. The FE model accurately captures both the static and pseudo-dynamic behaviour at the friction interface. Flexible-to-flexible contact surfaces with elastic friction capabilities are used to determine the pressure distribution. Static contact conditions are established by initially pressing the shoes against the drum. This first load step is followed by a gradual increase of applied rotation to the drum in order to define the maximum reacted braking torque and pseudo-dynamic pressure distribution at the transition point between sticking and sliding motion. The method clearly illustrates the changes in contact force that take place as a function of the applied pressure, coefficient of friction and initial gap between lining and rotor. These changes in contact area are shown to influence the overall stability and therefore squeal propensity of the brake assembly.

To maximize CO2 reduction, refined straight used cooking oils were used as a fuel in Heavy Goods Vehicles (HGVs) in this research. The fuel is called C2G Ultra Biofuel (C2G: Convert to Green Ltd) and is a fully renewable fuel made as a diesel replacement from processed used cooking oil, used directly in diesel engines specifically modified for this purpose. This is part of a large demonstration project involving ten 44-tonne trucks using C2G Ultra Biofuel as a fuel to partially replace standard diesel fuels. A dual fuel tank containing both diesel and C2G Ultra Biofuel and an on-board fuel blending system-Bioltec system was installed on each vehicle, which is able to heat the C2G Ultra Biofuel and automatically determine the required blending ratio of diesel and C2G Ultra Biofuel according to fuel temperature and engine load. The engine was started with diesel and then switched to C2G Ultra Biofuel under appropriate conditions.

The Carbon Dioxide (CO₂) emission from a EURO 3 diesel van over a real-world driving cycle were investigated utilizing part of the Leeds University - Headingly Ring Road (LU-HR) driving cycle, which comprises both an urban (congested) and extra-urban (high speed) driving section. The vehicle used in this research was a 1.8-liter Ford Connect TDCi diesel van. Emissions were monitored by a Portable Emissions Measurement System (PEMS) incorporating an on-board FTIR (Fourier Transform Infrared) exhaust emission measurement system, a Horiba On Board emissions measuring System (OBS 1300) which measured the exhaust flow rate and air/fuel ratio, and a RaceLogic VBOX II differential GPS system provided geographical position, speed and acceleration data. Route topography is known to have substantial influence on vehicle emission.

Non-exhaust and exhaust particles from traffic were evaluated to account for nearly equal proportions in traffic-related emissions. Among non-exhaust emissions, tyre wear has been a crucial contributor to Particulate matter (PM), with its mass contribution as high as 30% to non-exhaust emissions from traffic. As exhaust emissions control regulation becomes stricter, which leads to a substantial reduction in exhaust emissions from road traffic, currently relative contributions of non-exhaust particles generated from tyre wear to PM is becoming more important. Accordingly, possible regulatory requirement and effectively control strategy of tyre wear particles needs to be developed. This review paper covers the physical properties, chemical composition, emission rates, and mathematic model development of tyre wear particles.

This paper presents a method of control for a 6×6 series-configured Hybrid Electric Off-road Vehicle (HEOV). The vehicle concerned is an eight-tonne logistics support vehicle which utilizes Hub Mounted Electric Drives (HMED) at each of its six wheel stations. This set-up allows Individual Wheel Control (IWC) to be implemented to improve vehicle handling and mobility. Direct Yaw-moment Control (DYC) is a method of regulating individual wheel torque to control vehicle yaw motion, providing greater stability in cornering. When combined with both a Traction Control System (TCS) and an Anti-lock Braking System (ABS) the tire/road interaction is fully controlled, leading to improved control over vehicle dynamics, whilst also improving vehicle safety.

This paper proposes an advanced control strategy to improve vehicle handling and directional stability by integrating either Active Front Steering (AFS) or Active Rear Steering (ARS) with Variable Torque Distribution (VTD) control. Both AFS and ARS serve as the steerability controller and are designed to achieve the improved yaw rate tracking in low to mid-range lateral acceleration using Sliding Mode Control (SMC); while VTD is used as the stability controller and employs differential driving torque between left and right wheels on the same axle to produce a relatively large stabilizing yaw moment when the vehicle states (sideslip angle and its angular velocity) exceed the reference stable region defined in the phase plane. Based on these stand-alone subsystems, an integrated control scheme which coordinates the control actions of both AFS/ARS and VTD is proposed. The functional difference between AFS and ARS when integrated with VTD is explained physically.

Most active control systems developed for passenger vehicles are developed as safety systems. These control systems usually focus on improving vehicle stability and safety while ignoring the effects on the vehicle driveability. While stability is the primary concern of these control systems the driveability of the vehicle is also an important consideration. An example of compromised driveability in a stability control system is brake based active yaw control. Brake based systems are very effective at stability control but can have a negative impact on the longitudinal dynamics of a vehicle. The objective of the vehicle control systems developed for the future will be to preserve vehicle driveability while ensuring the stability of the vehicle. In this work, active suspension and active drivelines are developed as stability control systems that have a minimal impact on the driveability of the vehicle.

Many active control systems are developed as safety systems for passenger vehicles. These control systems usually focus on improving vehicle stability and safety while ignoring the effects on the vehicle driveability. In the motorsport environment, increased stability is desirable but not if the driveability of the vehicle is heavily compromised. In this work, active suspension and active drivelines are examined to improve vehicle dynamics and enhance driveability while maintaining stability. The active control systems are developed as separate driveability and stability controls and tested individually then integrated to create a multi-objective control system to improve both driveability and stability. The controllers are tested with standard vehicle manoeuvres.

Hydrogenated Vegetable Oil (HVO) diesel fuels have the potential to provide a reduced carbon footprint for diesel engines and reduce exhaust emissions. Therefore, it is a strong candidate for transport and diesel powered machines including electricity generators and other off-road machines. In this research, a waste cooking oil derived HVO diesel was investigated for its combustion and emission performance including ignition delays, size segregated particulate number emissions and gaseous emissions. The results were compared to the standard petroleum diesel. A EURO5 emission compliant three litre, direct injection, intercooled IVECO diesel engine equipped with EGR was used which has a maximum power output of 96kW. The engine was equipped with an integrated DOC and DPF aftertreatment system. Both the upstream and downstream of the aftertreatment emissions were measured. The tests were conducted at different RPM and loads at steady state conditions.

A non-contacting laser displacement meter has been used for dynamic measurements of the radial movement of a v-ribbed belt (type 3PK) around the arc of wrap running on a belt testing rig. Accurate and repeatable results are possible. Using this device, the belt radial movement and the beginning of rib bottom / groove tip contact around the arc of wrap have been determined experimentally for v-ribbed belts. Slip, torque loss, maximum torque capacity and efficiency have been measured during the tests.

Motion cueing algorithms can improve the perceived realism of a driving simulator, however, data on the effects on driver performance and simulator sickness remain scarce. Two novel motion cueing algorithms varying in concept and complexity were developed for a limited maneuvering workspace, hexapod/Stuart type motion platform. The RideCue algorithm uses a simple swing motion concept while OverTilt Track algorithm uses optimal pre-positioning to account for maneuver characteristics for coordinating tilt adjustments. An experiment was conducted on the US Army Tank Automotive Research, Development and Engineering Center (TARDEC) Ride Motion Simulator (RMS) platform comparing the two novel motion cueing algorithms to a pre-existing algorithm and a no-motion condition.