Search Results

A 2-D simulation of fluid dynamic and chemistry interaction following end gas autoignition has demonstrated three distinct modes of reaction, dependent upon the temperature gradient about an exothermic centre. All three modes (deflagration, developing detonation and thermal explosion) can contribute to knock; the developing detonation case, associated with intermediate temperature gradient, has been identified as the more damaging. The simulation code (LUMAD) has been used in a systematic parametric study designed to separate the complex interacting events which can lead to mixed modes in real engines. A most significant finding related to the sequential autoignition of multiple exothermic centres.

Different driving test cycles, the Leeds-West Park (LWP) loop and the Leeds-High Park (LHP) or HPL-A and B (Leeds-Hyde Park Loop-A or B, hereafter referred as HPL-A or B cycle) loop were selected for this urban intersection research and results are presented in this study. Different emissions-compliant petrol passenger cars (EURO 1, 2, 3 and 4) were compared for their real-world emissions. A reasonable distance of steady state speed was needed and for the analysis made in this paper were chosen vehicle speeds at ~20, ~30 and ~40 km/h. Specific spot of periods of driving at the speeds mentioned above were identified, then the starting and ending point was found and the total emissions in g for that period divided by the distance was calculated. A typical urban driving cycle including a loop and a section of straight road was used for the comparison test as it was similar to the legislative ECE15 urban driving cycle.

The tailpipe exhaust emissions were measured under real world urban driving conditions by using a EURO4 emissions compliant SI car equipped with an on-board heated FTIR for speciated gaseous emission measurements, a differential GPS for travel profiles, thermocouples for temperatures, and a MAX fuel meter for transient fuel consumption. Emissions species were measured at 0.5 Hz. The tests were designed to enable cold start to occur into congested traffic, typical of the situation of people living alongside congested roads into a large city. The cold start was monitored through temperature measurements of the TWC front and rear face temperatures and lubricating oil temperatures. The emissions are presented to the end of the cold start, defined when the downstream TWC face temperature is hotter than the front face which occurred at ∼350-400oC. Journeys at various times of the day were conducted to investigate traffic flow impacts on the cold start.

Fluctuations in the operational output of spark ignition engines are observed from one engine cycle to the other, when an engine is run at technically identical operating condition. These fluctuations known as cycle-to-cycle variations, when high, adversely affect the performance of an engine. Reduction in cycle-to-cycle variation in engines has been noted by researchers as one of the methods of improving engine efficiency and operational stability. This study investigated the combustion performance characteristics of two fuels: E5 (95% gasoline and 5% ethanol) and ULG98 (unleaded gasoline) in a spark ignition engine, operating at varying inlet pressure conditions and ignition timing. A two-stroke, 80mm bore, spark ignition engine was operated at an engine speed of 750 rpm, inlet pressures of 1.6 and 2.0 bar and spark-timings ranging from 2 to 13 bTDC. A top cylinder head with a centralized spark plug was used in all the experiments.

Replacing the conventional fossil fuel totally or partially with alcohols or ethers in spark-ignition (SI) engine is a promising way to reduce pollutant emissions. A large number of studies on alcohol-containing blends in SI engines could be found in the literature. Nonetheless, investigations of ether-containing blends are by far much less numerous, especially for modern boosted engines. Blending with ether compounds might change the burning rate at high pressure, which consequently changes the anti-knock properties of these fuels and leads to a deterioration in the vehicle drivability. This work reports experiments carried out in two one-cylinder engines: one is a naturally aspirated, variable compression ratio engine, and the other is a strongly charged optical engine. Three fuels with different RON and MON numbers were tested: Iso-octane, a blend Ethyl Tert Butyl Ether (ETBE) with a primary reference fuel, and a commercial gasoline fuel containing 5% by volume of ethanol (E05).

A v-ribbed belt is assumed to be a combination of a flat belt and a v-belt with the same radial movement of the two parts. Based on these assumptions a new theory is developed for the mechanical performance of v-ribbed belt drives, which gives a new modification to Euler's equation (capstan formula). The experimental and theoretical results comparison show that the radial movement of the v-ribbed belt with rib bottom / groove tip contact is slightly less than the values without contact.

Light-duty China-6, which is among the most stringent vehicle exhaust emission standards globally, mandates the monitoring and reporting of real driving emissions (RDE) from July, 2023. In the process of regulation promulgation and verification, more than 300 RDE tests have been performed on over 50 China-5 and China-6 certified models. This technical paper endeavors to summarize the experience of RDE practice in China, and discuss the impacts of some boundary conditions (including vehicle dynamic parameters, data processing methods, hybrid propulsion and testing altitude) on the result of RDE measurement. In general, gasoline passenger cars confront few challenges to meet the upcoming RDE NOx requirement, but some China-5 certified samples, even powered by naturally-aspirated engines may have PN issues. PN emissions from some GDI-hybrid powertrain systems also need further reduction to meet China-6 RDE requirements.

Numerical investigations are reported on the location of sites at which autoignition first develops in the end-gas ahead of a spark-ignited flame in a combustion chamber following rapid compression of an alkane + air mixture to high pressures and temperatures. Attention is drawn to the part played by the reactions that give rise to a negative temperature coefficient of reaction rate in an inhomogeneous temperature field. A ‘reduced’ kinetic mechanism was employed to model the spontaneous oxidation of n-alkanes. Flame propagation was described in terms of the ‘eddy dissipation concept’ and coupled to the more detailed mechanism by means of a switching algorithm. The CFD calculations were performed by use of KIVA II.

Current trends in automotive engine design are towards smaller, lighter components operating under higher specific loads. Consequently, engine bearings are expected to operate under highly stressed conditions, with minimum lubricant film thicknesses falling below 1μm. There is, however, insufficient understanding of acceptable tolerances on surface geometry of bearing shells and crankshaft pins. Measurement data suggest that some engine crankpins are machined with as many as 21 circumferential lobes. Some lobes have amplitudes in excess of 5 μm and are thought to be responsible for premature bearing damage. This study presents results from a theoretical analysis of dynamically loaded journal bearings with circumferential lobes on the journal. The Reynolds equation for a rigid journal bearing is solved for an incompressible, Newtonian, iso-viscous lubricant, with a flow conserving cavitation model accommodating oil film history.

The influence of nozzle sac volume on the composition of the fuel derived solvent organic fraction of diesel particulate from a naturally aspirated 1 litre per cylinder diesel engine was studied. Significant differences in the quantities of the polycyclic aromatic compounds for different sac volumes were found. The emission differences were due to the reduction of unburnt fuel contributions to particulate SOF as the sac volume was reduced.

Reported in the current paper is a study of the effects of Nitric Oxide (NO) within a simulated Exhaust Gas Residual (sEGR) on Spark Ignition (SI) engine end gas autoignition. A modified version of the single cylinder Leeds University Ported Optical Engine Version 2 (LUPOE-2) engine was designed to completely eliminate retained residual gas and so allow unambiguous definition of the composition of the in-cylinder charge. The engine was alternately operated on stoichiometric mixtures of iso-octane, two Primary Reference Fuels (PRF), a Toluene Reference Fuel (TRF), and a commercially available Unleaded Gasoline (ULG) and air. These mixtures were diluted with sEGR (products of the complete stoichiometric combustion of the given fuel/air mixture) in mass fractions ranging from 0-15%; with and without 5000ppm NO (0.52% by mass) within that sEGR.

Modern engine developments result in very different gas pressure-temperature histories to those in RON/MON determination tests and strain the usefulness of those knock scales and their applicability in SI engine knock and HCCI autoignition onset models. In practice, autoignition times are complex functions of fuel chemistry and burning velocity (which affects pressure-temperature history), residual gas concentration and content of species such as NO. As a result, autoignition expressions prove inadequate for engine conditions straying far from those under which they were derived. The currently reported study was designed to separate some of these effects. Experimental pressure crank-angle histories were derived for an engine operated in skip-fire mode to eliminate residuals. The unburned temperature history was derived for each cycle and was used with a number of autoignition/knock models.

Diesel engine exhaust pipe and incylinder deposits were analysed for the global fuel, lube oil, carbon and ash fractions for a range of diesel engines. A large SOF fraction, typically 30%, was found and this was dominated by lubricating oil. These deposits are shown to contain significant levels of PAH and hence provide a source of diesel PAH emissions and possible sites for incylinder pyrosynthesis of high molecular weight PAH. A Perkins 4-236 NA DI was used to investigate the role of exhaust pipe deposits on PAH emissions. It was shown that PAH compounds could be volatilised from the exhaust pipe. The difference in the exhaust inlet and outlet particulate composition for diesel and kerosene fuels was used to quantify the n-alkane and PAH emissions originating from the exhaust pipe deposits. Comparison with pure PAH free fuels showed that the exhaust outlet PAH composition was similar to that expected from the exhaust pipe deposits.

Initial results are presented for the production of hydrogen from waste lubricating oil using a chemical looping reforming (CLR) process. The development of flexible and sustainable sources of hydrogen will be required to facilitate a "hydrogen economy." The novel CLR process presented in this paper has an advantage over hydrogen production from conventional steam reforming because CLR can use complex, low value, waste oils. Also, because the process is scalable to small and medium size, hydrogen can be produced close to where it is required, minimizing transport costs. Waste lubricating oil typically contains 13-14% weight of hydrogen, which through the steam reforming process could produce a syngas containing around 75 vol% H₂, representing over 40 wt% of the fuel. The waste oil was converted to a hydrogen-rich syngas in a packed bed reactor, using a Ni/ Al₂O₃ catalyst as the oxygen transfer material (OTM).