Search Results

The acoustics of automotive intake and exhaust systems is typically modeled using linear acoustics or gas-dynamics simulation. These approaches are preferred during basic sound design in the early development stages due to their computational efficiency compared to complex 3D CFD and FEM solutions. The linear acoustic method reduces the component being modelled to an equivalent acoustic two-port transfer matrix which describes the acoustic characteristic of the muffler. Recently this method was used to create more detailed and more accurate models based on a network of 3D cells. As the typical automotive muffler includes perforated elements and sound absorptive material, this paper demonstrates the extension of the 3D linear acoustic network description of a muffler to include the aforementioned elements. The proposed method was then validated against experimental results from muffler systems with perforated elements and sound absorptive material.

Beside hard facts as performance, emissions and fuel consumption especially the brand specific attributes such as styling and sound are very emotional, unique selling prepositions. To develop these emotional characters, within the given boundary conditions of the future pass-by regulation, it is necessary to define them at the very beginning of the project and to follow a consequent development process. The following paper shows examples of motorcycle NVH development work on noise cleaning and sound engineering using a hybrid development process combining front loading, simulation and testing. One of the discussed solutions is the investigation of a piston pin offset in combination with a crankshaft offset for the reduction of friction. The optimization of piston slap noise as a result of the piston secondary motion was performed by simulation. As another example a simulation based development was performed for the exhaust system layout.

The European Emissions Stage 5b standard for diesel passenger cars regulates particulate matter to 0.0045 g/km and non-volatile part/km greater than 23 nm size to 6.0x10₁₁ as determined by the PMP procedure that uses a heated evaporation tube to remove semi-volatile material. Measurement artifacts associated with the evaporation tube technique prevents reliable extension of the method to a lower size range. Catalytic stripper (CS) technology removes possible sources of these artifacts by effectively removing all hydrocarbons and sulfuric acid in the gas phase in order to avoid any chemical reactions or re-nucleation that may cause measurement complications. The performance of a miniature CS was evaluated and experimental results showed solid particle penetration was 50% at 10.5 nm. The sulfate storage capacity integrated into the CS enabled it to chemically remove sulfuric acid vapor rather than rely on dilution to prevent nucleation.

The accurate prediction of pollutant emissions generated by IC engines is a key aspect to guarantee the respect of the emission regulation legislation. This paper describes the approach followed by the authors to achieve a strict numerical coupling of two different 1D modeling tools in a co-simulation environment, aiming at a reliable calculation of engine-out and tailpipe emissions. The main idea is to allow an accurate 1D simulation of the unsteady flows and wave motion inside the intake and exhaust systems, without resorting to an over-simplified geometrical discretization, and to rely on advanced thermodynamic combustion models and kinetic sub-models for the calculation of cylinder-out emissions. A specific fluid dynamic approach is then used to track the chemical composition along the exhaust duct-system, in order to evaluate the conversion efficiency of after-treatment devices, such as TWC, GPF, DPF, DOC, SCR and so on.

Car components are exposed to the random/harmonic/impact excitation which can result in component failure due to vibration fatigue. The stress and strain loads do depend on local stress concentration effects and also on the global structural dynamics properties. Standardized fatigue testing is long-lasting, while the dynamic fatigue testing can be much faster; however, the dynamical changes due to fatigue are usually not taken into account and therefore the identified fatigue and structural parameters can be biased. In detail: damage accumulation results in structural changes (stiffness, damping) which are hard to measure in real time; further, structural changes change the dynamics of the loaded system and without taking this changes into account the fatigue load in the stress concentration zone can change significantly (even if the excitation remains the same). This research presents a new approach for accelerated vibration testing of real structures.

Upcoming, increasingly stringent greenhouse gas (GHG) as well as emission limits demand for powertrain electrification throughout all vehicle applications. Increasing complexity of electrified powertrain architectures require an overall system approach combining modular component technology with integration and industrialization requirements when heading for further significant efficiency optimization. At the same time focus on reduced development time, product cost and minimized additional investment demand reuse of current production, machining, and assembly facilities as far as possible. Up to date additive manufacturing (AM) is an established prototype component, as well as tooling technology in the powertrain development process, accelerating procurement time and cost, as well as allowing to validate a significantly increased number of variants. The production applications of optimized, dedicated AM-based component design however are still limited.

Due to the increasing pressure to develop small-size and low-cost after-treatment systems meeting the legislative demands it is desirable to integrate multiple functionalities and exploit any possible synergies. Typical examples include DPFs catalyzed with deNOx catalysts, as well as LNT-SCR combinations using layered coating technology. The present paper deals with the modeling challenges involved for the proper simulation of such advanced concepts. Key role in such advanced simulation attempts has the coupling between diffusion-reaction phenomena, which is captured through intra-layer modeling. All investigations in this paper deal with the application of possible combined LNT-SCR system configurations. The simulation results show that a dual bed LNT- passive SCR configuration offers substantial NOx emissions reductions compared to a single LNT catalyst and effectively controls secondary NH3 emissions produced during LNT regeneration phases.

Non-combustible particles, commonly summarized as ash, influence the lifetime performance of wall flow filters. This study aims to investigate this influence by means of simulation. An existing transient 1D+1D wall flow filter model is extended by dedicated transport balances for soot and ash (1), by a discrete cake model describing changing soot and ash compositions over the cake height (2), by a phenomenological cake filtration model (3), by dedicated cake property models (4) and by a phenomenological model capturing the radial mobility of solids within the cake (5). Results of three different types of simulations are shown. First, the various sub-models are assessed in isolated simulation configurations. The combination of these shall serve as theoretical model validation. Second, isolated loading and passive regeneration simulations are performed.

Approaching engineering limits for the thermal design of battery modules requires virtual prototyping and appropriate models with respect to physical depth and computational effort. A multi-scale and multi-domain model describes the electrochemical behavior of a single battery unit cell in 1D+1D at the level of intra-cell phenomena, and it applies a 3D thermal model at module level. Both models are connected within a common vehicle simulation platform. The models are discussed with special emphasis on battery degradation such as solid electrolyte interphase layer formation, decomposition and lithium plating. The performance of the electrochemical model is assessed by discharge cycles and repeated charge/discharge simulations. The thermal module model is compared to CFD reference data and studied with respect to its grid sensitivity.

Non-exhaust emissions are clearly one of the focal points for the upcoming Euro 7 legislation. The new United Nations Global Technical Regulation (UN GTR) defining the framework for brake emission measurements is about to be officially published. The first amendment to this text is already on the way through the United Nations Economic Commission for Europe (UNECE) hierarchy for decision making. In real life, the final emission factor as the ultimate result of a test is influenced by inaccuracies of numerous parts of the measurement system as well as additional contributing factors like the performance of the particulate filter handling process, which might not be primarily related to equipment specifications.

Calibrating a vehicle’s powertrain for dynamic operation needs to focus on efforts to mitigate the risks of thermal overload which may arise in the stator or rotor components of an e-motor. Risks also may arise for expected NVH or durability targets, with torque and torque “oscillations” acting as primary sources for the vehicles’ NVH behavior. Both topics, temperature measurement of stator and rotor as well as dynamic torque measurements of the powertrain’s drive shaft are addressed with examples demonstrating the sensors applications in normal test bed and vehicle configurations.

The rare occurrence during city driving of the exhaust temperature levels required for ceramic trap regeneration without catalytic aid, seems to be the main reason of delay in wide application of the trap. The use of catalysts seems to be more or less necessary. Study of the catalytic activity during trap regeneration had not been very effective so far. This holds equally true for the case of catalyzed trap as for the case of catalytic fuel additives. The lack of a satisfactory theory for the explanation and prediction of catalytic activity, directed international research and development towards the quest of the optimum catalyst, which could support a very simple and low-cost regeneration system. The new approach to the explanation of catalytic activity presented in this paper, denies the above assumption.

In this study, tailpipe-sampling was used to sample the exhaust aerosol of a Stage IV tractor equipped with Diesel Oxidation Catalyst (DOC) and Selective Catalytic Reduction (SCR) aftertreatment systems. The particle emissions were characterized in terms of number concentration (particle size of > 2.5 nm), mass concentration (particle size of 6-612 nm) BC mass concentration and chemical composition (particle size of > 30 nm). The measurements were conducted on-road by setting a mobile laboratory on a trailer and pulling it with the tractor. In addition to driving, heavy-lift work cycles were tested, where separate lifts of a 1000 kg weight were conducted with the front fork of the tractor with two minutes of idling between consecutive lifts. Both a Porous Tube Diluter (PTD) with ambient temperature dilution air as well as an ejector diluter with hot dilution air were used to sample the exhaust aerosol.

The first two of a series of traps retrofitted on a pilot fleet of 110 buses of the Athens Bus Corporation were removed for examination after 100,000 km of revenue service. These buses were gradually equipped with the ELBO Trap Oxidiser since the beginning of 1989 and are constantly operated on Cerium based fuel additive. The physical properties and the chemical composition of filters and ash residues were analysed by the filter manufacturers and the fuel additive producer. The results have shown that after two years of operation the filter material remained intact and the ash deposits (consisting mainly of CeO2) exhibit a limited interaction with the cordierite. More than 94% of these deposits are filtered by the monoliths and could be removed to a large extent with the application of conventional methods.

To achieve low tailpipe NOX emissions in Heavy-Duty engines, the rapid warm-up of the exhaust aftertreatment system (EAS) needs to be assisted by the adoption of new technologies to reduce engine-out emissions and increase the EAS conversion efficiency. Engine measures like cylinder deactivation, retarded start of the main injection, late intake valve closing, intake throttling and elevated idle speed can substantially increase the available exhaust gas enthalpy and temperature at the expense of additional fuel as has been shown in the literature. On the other hand, the exhaust system can be optimized in terms of hardware and controls, which is nowadays strongly supported by simulation. However, these simulation studies typically assume a fixed engine hardware and calibration and thus fixed engine-out simulation boundary conditions. Moving forward to tougher and real-world oriented legislation, the fixed cycle and engine-out boundary condition becomes insufficient.

The acoustic simulation of internal combustion engine exhaust systems is an important aspect to meet customer expectations and legislation targets. One dimensional gas dynamic simulation tools are used for the calculation of the exhaust orifice noise in the early stages of the engine development process. This includes the prediction of the acoustic performance of individual components in the exhaust line. One common element used in exhaust systems to increase the acoustic damping is the plug flow muffler. This study looks at the prediction of acoustic performance of various plug mufflers at different flow velocities. These include a single plug muffler, a double plug muffler and an eccentric plug muffler with different porosities for the perforated sections. To this purpose a generic 3D cell approach was developed and applied.

Wall flow particulate filters have been used as a standard exhaust aftertreatment device for many years. The interaction of particulate matter (PM) regeneration and catalytically supported reactions strongly depends on the given operating conditions. Temperature, species concentration and mass flow cause a change from advective to diffusive-controlled flow conditions and influence the rate controlling dominance of individual reactions. A transient 1D+1D model is presented considering advective and diffusive transport phenomena. The reaction scheme focuses on passive PM conversion and catalytic oxidation of NO. The model is validated with analytical references. The impact of back-diffusion is explored simulating pure advective and combined advective diffusive species transport. Rate approaches from literature are applied to investigate PM conversion at various operating conditions.

Dynamometer (dyno) durability testing plays a significant role in reliability and durability assessment of commercial engines. Frequently, durability test procedures are based on warranty history and corresponding component failure modes. Evolution of engine designs, operating conditions, electronic control features, and diagnostic limits have created challenges to historical-based testing approaches. A physics-based methodology, known as Load Matrix, is described to counteract these challenges. The technique, developed by AVL, is based on damage factor models for subsystem and component failure modes (e.g. fatigue, wear, degradation, deposits) and knowledge of customer duty cycles. By correlating dyno test to field conditions in quantifiable terms, such as customer equivalent miles, more effective and efficient durability test suites and test procedures can be utilized. To this end, application of Load Matrix to a heavy-duty diesel engine is presented.

Five very different exhaust ports of diesel and gasoline engines are investigated under steady and unsteady flow to determine whether their flow coefficients are sensitive to unsteady flow. Valve lift is fixed for a specific test but varied from test to test to determine whether the relationship between steady and unsteady flow is lift dependent. The pulse frequency is chosen to correspond to the blow-down phase of an engine running at approximately 6000 rpm, but the pressure drop across the port is much smaller than that present in a running engine. Air at room temperature is used as the working fluid. It is shown that unsteady flow through the five exhaust ports causes, at most, a 6% increase or a 7% decrease in flow coefficient.

The continuously decreasing emission limits lead to a growing importance of exhaust aftertreatment in Diesel engines. Hence, methods for achieving a rapid catalyst light-off after engine cold start and for maintaining the catalyst temperature during low load operation will become more and more necessary. The present work evaluates several valve timing strategies concerning their ability for doing so. For this purpose, simulations as well as experimental investigations were conducted. A special focus of simulation was on pointing out the relevance of exhaust temperature, mass flow and enthalpy for these thermomanagement tasks. An increase of exhaust temperature is beneficial for both catalyst heat-up and maintaining catalyst temperature. In case of the exhaust mass flow, high values are advantageous only in case of a catalyst heat-up process, while maintaining catalyst temperature is supported by a low mass flow.