Search Results

This paper studies autoignition characteristics and HCCI engine combustion of ketone fuels, which are important constituents of recently discovered fungi-derived biofuels. Two ketone compounds, 2,4-dimethyl-3-pentanone (DMPN) and cyclopentanone (CPN), are systematically investigated in the Sandia HCCI engine, and the results are compared with conventional gasoline and neat ethanol. It is found that CPN has the lowest autoignition reactivity of all the biofuels and gasoline blends tested in this HCCI engine. The combustion timing of CPN is also the most sensitive to intake-temperature (Tin) variations, and it is almost insensitive to intake-pressure (Pin) variations. These characteristics and the overall HCCI performance of CPN are similar to those of ethanol. In contrast, DMPN shows multi-faceted autoignition characteristics. On the one hand, DMPN has strong temperature-sensitivity, even at boosted Pin, which is similar to the low-reactivity ethanol and CPN.

The gaseous fuels, hydrogen and methane, are fuels that will likely be in adequate supply when crude oil sourced liquid fuels are scarce. These gases may he used directly in engines, which may need modification or could be used as feed stocks for liquid fuel synthesis. The energy efficiency of using methane and hydrogen in dedicated engines is compared with liquid fuelled engines. Hydrogen gives 6 3% improved efficiency and Methane 39% in city driving and Methane gives slightly improved power but Hydrogen fuel causes a 25% power loss compared with petrol. The storage of Methane in compressed or liquid form and Hydrogen in metal hydrides are compared. The overall efficiency of these gaseous fuel systems are compared, and fuel synthesis is included.

This paper compares the performance, efficiency, emissions and combustion parameters of a prototype two cylinder 430 cm3 engine which has been tested in a variety of normally aspirated (NA) modes with compression ratio (CR) variations. Experiments were completed using 98-RON pump gasoline with modes defined by alterations to the induction system, which included carburetion and port fuel injection (PFI). The results from this paper provide some insight into the CR effects for small NA spark ignition (SI) engines. This information provides future direction for the development of smaller engines as engine downsizing grows in popularity due to rising oil prices and recent carbon dioxide (CO2) emission regulations. Results are displayed in the engine speed, manifold absolute pressure (MAP) and CR domains, with engine speeds exceeding 10000 rev/min and CRs ranging from 9 to 13. Combustion analysis is also included, allowing mass fraction burn (MFB) comparison.

This paper describes the design and development of an engine with constant power for SAE's student Formula race-car competition, allowing the avoidance of gear shifting for much of the Autocross event. To achieve constant power for over 50% of the speed range, turbocharging was adopted with a boost pressure ratio of 2.8 at mid-range speeds and applied to an engine capacity of 430 cc. This engine was specifically designed and configured for the purpose, being a twin cylinder in-line arrangement with double overhead camshafts. Most of the engine components were specially cast or machined from billets. The capacity was selected to minimise frictional losses and thus increase delivered power along with dry sump lubrication and a three speed gear box. The engine manifolds and plenums were designed using a CAE application and proved to be well suited to the task resulting in excellent agreement between predicted and actual performance.

The hydrogen assisted jet ignition system (HAJI) replaces the spark plug of an Otto cycle engine and consists of a very small pre-chamber into which a hydrogen injector and spark plug are installed. The HAJI system allows stable combustion of very lean main-chamber hydrocarbon mixtures, leading to improved thermal efficiency and very much reduced NOx emissions. The current investigation focuses on the application of HAJI to a modern pent-roof, four valve per cylinder automotive engine. The development of a new hydrogen injection system and HAJI pre-chamber based on proprietary gasoline and diesel injectors is described. Results from injector and engine performance testing are presented in detail.

The HAJI (Hydrogen Assisted Jet Ignition) system for S.I. engines utilises direct injection of small amounts of hydrogen to enhance the combustion of a variety of automotive fuels. Although not the primary purpose of HAJI, the hardware, once in place, also lends itself to the possibility of hydrogen-only running during a cold start. Cold-start simulations have been performed using a single cylinder engine. Results are presented, comparing hydrogen-only tests with standard HAJI operation and normal spark-ignition operation. HAJI and spark ignition tests were carried out with gasoline as the main-chamber fuel. Emission levels and combustion stability characteristics were recorded as the engine warmed up. The differences between the various fueling/ignition scenarios are presented and the implications for possible automotive applications are discussed in light of current and proposed emissions legislation.

This paper describes the turbocharger development of a restricted 430 cm3 odd firing two cylinder engine. The downsized test engine used for development was specifically designed and configured for Formula SAE, SAE's student Formula race-car competition. A well recognised problem in turbocharging Formula SAE engines arises from the rules, which dictate that the throttle and air intake restrictor must be on the suction side of the compressor. As a consequence of upstream throttling, oil from the compressor side seal assembly is drawn into the inlet manifold. The development process used to solve the oil consumption issue for a Garrett GT-12 turbocharger is outlined, together with cooling and control issues. The development methodology used to achieve high pressure ratio turbocharging is discussed, along with exhaust manifold development and operating limitations. This includes experimental and modeling results for both pulse and constant pressure type turbocharging.

This paper describes the mechanical component design, lubrication, tuning and control aspects of a restricted, odd fire, highly turbocharged (TC) engine for Formula SAE competition. The engine was specifically designed and configured for the purpose, being a twin cylinder inline arrangement with double overhead camshafts and four valves per cylinder. Most of the engine components were specially cast or machined from billets. A detailed theoretical analysis was completed to determine engine specifications and operating conditions. Results from the analysis indicated a new engine design was necessary to sustain highly TC operation. Dry sump lubrication was implemented after initial oil surge problems were found with the wet sump system during vehicle testing. The design and development of the system is outlined, together with brake performance effects for the varying systems.

The goal of hydrogen engine research is to achieve highest possible efficiency with low NOx emissions. This is necessary for the hydrogen car to remain competitive with the ever-improving efficiency of conventional fuel's use, to take advantage of the increased availability of hydrogen distribution for fuel cells and to achieve better range than battery electric vehicles. This paper examines the special problems of hydrogen engine combustion and ways to improve efficiency. Central to this are the effects of compression ratio (CR) and lambda (excess air ratio) and ignition system. The results demonstrate highest indicated thermal efficiency at ultra lean condition of lambda ≻ 2 and with central ignition. This need for this lean mixture is partly explained by the higher heat transfer losses.

This paper presents a numerical study of trace knocking combustion of ethanol/gasoline blends in a modern, single cylinder SI engine. Results are compared to experimental data from a prior, published work [1]. The engine is modeled using GT-Power and a two-zone combustion model containing detailed kinetic models. The two zone model uses a gasoline surrogate model [2] combined with a sub-model for nitric oxide (NO) [3] to simulate end-gas autoignition. Upstream, pre-vaporized fuel injection (UFI) and direct injection (DI) are modeled and compared to characterize ethanol's low autoignition reactivity and high charge cooling effects. Three ethanol/gasoline blends are studied: E0, E20, and E50. The modeled and experimental results demonstrate some systematic differences in the spark timing for trace knock across all three fuels, but the relative trends with engine load and ethanol content are consistent. Possible reasons causing the differences are discussed.

HAJI (Hydrogen Assisted Jet Ignition) is an advanced combustion initiation system for otherwise standard S.I engines. It utilises the fluid mechanics of a turbulent, chemically active jet, combined with the reliability of spark igniting rich hydrogen mixtures. The result is an extremely robust ignition system, capable of developing power from an engine charged with air-fuel mixtures as lean as λ = 5. Experiments have been performed using a single cylinder engine operating on gasoline in the speed range of 600-1800 r/min. Data are presented in the form of maps which describe fuel efficiency, combustion stability and emissions with respect to load, speed, air-fuel ratio and throttle. The results are incorporated into a model of a known engine and vehicle and this is used to estimate performance over the Federal drive-cycle.

This paper presents a study of the performance of a 6-cylinder, spark-ignited, port-fuel-injected, production engine modified for hydrogen fueling. The engine modifications include turbo-charging, multiple fuel injectors per port and charge-dilution control techniques. Pumping losses are reduced through ultra-lean burn and throttle-less operation alongside high charge dilution ratio control achieved by twin independent variable cam timing without external EGR. Lean-burn combustion, engine-out emissions and brake thermal efficiency results are examined in detail. In particular, low NO emissions and brake thermal efficiencies near 38% are observed experimentally at the same operating conditions. The former is explained in terms of the usual thermal NOx pathway. Usage of throttle position, injection timings and cam timings for avoiding preignition and knock over the entire engine map are also discussed.

HAJI, or Hydrogen Assisted Jet Ignition, is an ignition system which uses a hot gaseous jet to initiate and stabilise combustion. HAJI allows a dramatic reduction of cyclic variability, and an extension of the lean limit of the engine to lambda 5. Improvements in cyclic variability lead to increased power output, reduced noise, wear on components and emissions. The ability to operate ultra lean gives 25% improvements in efficiency and extremely low emissions, particularly of NOx. Combustion analysis based on the fractal dimensions of the propagating flame fronts, obtained from optical flame data, support the hypothesis of enhancement of flame speeds through the presence of active chemical species. However, the relative contributions of turbulence and active species to the mechanisms of combustion enhancement realised with HAJI are not well defined. HAJI ignition has also been simulated with a comprehensive three dimensional combustion code, KIVA3.

In this paper, performance, efficiency and emission experimental results are presented from a prototype 434 cm3, highly turbocharged (TC), two cylinder engine with brake power limited to approximately 60 kW. These results are compared to current small engines found in today's automobile marketplace. A normally aspirated (NA) 1.25 liter, four cylinder, modern production engine with similar brake power output is used for comparison. Results illustrate the potential for downsized engines to significantly reduce fuel consumption while still maintaining engine performance. This has advantages in reducing vehicle running costs together with meeting tighter carbon dioxide (CO2) emission standards. Experimental results highlight the performance potential of smaller engines with intake boosting. This is demonstrated with the test engine achieving 25 bar brake mean effective pressure (BMEP).

This paper reports comparative results for liquid phase versus gaseous phase port injection in a single cylinder engine. It follows previous research in a multi-cylinder engine where liquid phase was found to have advantages over gas phase at most operating conditions. Significant variations in cylinder to cylinder mixture distribution were found for both phases and leading to uncertainty in the findings. The uncertainty was avoided in this paper as in the engine used, a high speed Waukesha ASTM CFR, identical manifold conditions could be assured and MBT spark found for each fuel supply system over a wide range of mixtures. These were extended to lean burn conditions where gaseous fuelling in the multi-cylinder engine had been reported to be at least an equal performer to liquid phase. The experimental data confirm the power and efficiency advantages of liquid phase injection over gas phase injection and carburetion in multi-cylinder engine tests.