Search Results

The dust holding capacity of air cleaning filter depends on the size distribution of the particles. Traditional test dusts like Arizona road dust consist of a single mode of coarse particles. The purpose of this study is to evaluate the dust holding capacities of air filters with a bi-modal test dust that simulates the dust in atmospheric environments. The fine mode of the test dust consists of submicron Alumina particles that represent the fine particles in atmosphere. The coarse mode consists of traditional AC fine dust. The fine and coarse dusts are mixed in different mass ratios to simulate different atmospheric conditions. The ratios are 100% fine, 50%/50%, 25%/75%, 10%/90%, and 100% coarse. An engine air filter and a HVAC filter were studied with the bi-modal test dusts. The filter pressure drops were measured as a function of the dust loading. The results show that the flow resistance rises significantly faster as the ratio of fine to coarse fraction increases.

Diesel fuel injection systems are operating at increasingly higher pressure (up to 250 MPa) with smaller clearances, making them more sensitive to diesel fuel contaminants. Most liquid particle counters have difficulty detecting particles <4 μm in diameter and are unable to distinguish between solid and semi-solid materials. The low conductivity of diesel fuel limits the use of the Coulter counter. This raises the need for a new method to characterize small (<4 μm) fuel contaminants. We propose and evaluate an aerosolization method for characterizing solid particulate matter in diesel fuel that can detect particles as small as 0.5 μm. The particle sizing and concentration performance of the method were calibrated and validated by the use of seed particles added to filtered diesel fuel. A size dependent correction method was developed to account for the preferential atomization and subsequent aerosol conditioning processes to obtain the liquid-borne particle concentration.

Many engine exhaust emissions measurements require exhaust dilution. With low-emission engines, there is the possibility for contaminants in the dilution air to contribute artifacts to the emissions measurement. The objectives of this work are to discuss common methods used to clean the dilution air, to present the detailed analysis of a pressure swing adsorption (PSA) system and to compare the performance of the PSA with 2 other systems commonly used to provide dilution air for engine exhaust nanoparticle measurements. The results of the comparison are discussed in context with some emissions measurements that require exhaust dilution.

In many operating regimes, exhaust gas recirculation (EGR) while maintaining MBT spark timing improves cycle efficiency in SI engines. As the level of exhaust dilution is increased, the flame speed is reduced and the combustion rate is impaired. This leads to a drop in fuel economy as EGR rates are increased beyond the optimal level. To take advantage of the efficiency benefit of EGR without incurring the penalties of late combustion, a sensor which detects late combustion is tested. The signal from an ionization sensor placed near the exhaust port has been found to correlate to combustion which continues late into the expansion stroke. It may be possible to use the output from the ion sensor to maintain the EGR at the the optimum for fuel economy.

Combustion characteristics of an L-head engine combustion chamber have been examined using ionization probes and piezioelectric pressure transducers. The method describes how pressure rise rates, peak pressures, mean effective pressures, and flame arrival times were recorded. The flame arrival times were then used to find the position and shape of the flame front as a function of time. The influence of spark plug location on the above parameters was then examined for two different combustion chamber shapes.

Partially premixed low temperature combustion (LTC) in diesel engines is a strategy for reducing soot and NOX formation, though it is accompanied by higher unburned hydrocarbon (UHC) emissions compared to conventional mixing-controlled diesel combustion. In this work, two independent methods of quantifying light UHC species from a diesel engine operating in early LTC (ELTC) modes were compared: Fourier transform infrared (FT-IR) spectroscopy and gas chromatography-mass spectroscopy (GC-MS). A sampling system was designed to capture and transfer exhaust samples for off-line GC-MS analysis, while the FT-IR sampled and quantified engine exhaust in real time. Three different ELTC modes with varying levels of exhaust gas recirculation (EGR) were implemented on a modern light-duty diesel engine. GC-MS and FT-IR concentrations were within 10 % for C2H2, C2H4, C2H6, and C2H4O. While C3H8 was identified and quantified by the FT-IR, it was not detected by the GCMS.

A key challenge for the practical introduction of dual-fuel reactivity controlled compression ignition (RCCI) combustion modes in diesel engines is the requirement to store two fuels on-board. This work demonstrates that partially reforming diesel fuel into less reactive products is a promising method to allow RCCI to be implemented with a single stored fuel. Experiments were conducted using a thermally integrated reforming reactor in a reformed exhaust gas recirculation (R-EGR) configuration to achieve RCCI combustion using a light-duty diesel engine. The engine was operated at a low engine load and two reformed fuel percentages over ranges of exhaust gas recirculation (EGR) rate and main diesel fuel injection timing. Results show that RCCI-like emissions of NOx and soot were achieved load using the R-EGR configuration. It was also shown that complete fuel conversion in the reforming reactor is not necessary to achieve sufficiently low fuel reactivity for RCCI combustion.

The purpose of this study is to compare the dust loading behavior of ten filter media. The filters are used in engine air filtration, self-cleaning industrial air cleaners, building heating ventilation and cooling (HVAC), automotive cabin air filtration, air respirators, and general purpose air cleaning. Several types of filter media are tested. The filters include cellulose, synthetic (felt), glass, dual-layered glass/cellulose, mixed synthetic/glass, gradient packing glass, and electrically charged fibers. The initial pressure drops and fractional collection efficiencies as a function of particle size are reported. The filters were evaluated with two test dusts to investigate the size-dependent dust loading behavior. The two test dusts are SAE fine and submicron alumina powder (median diameter 0.25 μm). The results are analyzed and compared. It was found that the cellulose filters exhibited surface loading behavior and have the fastest growth of pressure drops.

Alcohols are examined as supplemental carbureted fuels for highspeed turbocharged diesels as typified by the White Motor/Waukesha F310 DBLT (6 cylinder, 310 cu. in.). Most of the work was with methanol; ethanol and isopropanol were compared at a few points. Fumigation (dual-fueling) with alcohol significantly reduced smoke and intake manifold temperature. These effects were largest at high load. Efficiency and HC emissions were essentially unchanged. Cylinder pressures and rise rates were examined for possible adverse effects on engine structure. The range of speed and load favorable to alcohol dual-fueling are such that, should alcohols become economically competitive as fuels, a practical duel-fuel system could be applied to existing diesel engines.

The impact of compression ratio on engine efficiency is well known. A plethora of mechanical concepts have been proposed for altering engine compression ratio in real time. Some of these, like free-piston configurations or complex crank-slider mechanisms have the added ability to alter piston trajectory along with compression ratio. This secondary modality raises the question: Is there a more optimal piston position versus crank-angle profile for spark-ignition (SI) engines than the near-sinusoidal motion produced by a traditional four-bar crank-slider mechanism? Very little published literature directly addresses this question. This work presents the results of a quasi-dimensional SI engine model using piston trajectory as an input. Specific trajectory traits including increased dwell at top dead center and asymmetric compression and expansion strokes were swept. The trajectory also was optimized using a single objective genetic algorithm with 60 individuals and 40 generations.

Diesel particulate filter (DPF) technology has proven performance and reliability. However, the addition of a DPF adds significant cost and packaging constraints leading some manufacturers to design engines that reduce particulate matter in-cylinder. Such engines utilize high fuel injection pressure, moderate exhaust gas recirculation and modified injection timing to mitigate soot formation. This study examines such an engine designed to meet US EPA Interim Tier 4 standards for off-highway applications without a DPF. The engine was operated at four steady state modes and aerosol measurements were made using a two-stage, ejector dilution system with a scanning mobility particle sizer (SMPS) equipped with a catalytic stripper (CS) to differentiate semi-volatile versus solid components in the exhaust. Gaseous emissions were measured using an FTIR analyzer and particulate matter mass emissions were estimated using SMPS data and an assumed particle density function.

Previously, the authors have proposed a novel strategy called trajectory based combustion control for the free piston engine (FPE) where the shape of the piston trajectory between top and bottom dead centers is used as a control input to modulate the chemical kinetics of the fuel-air mixture inside the combustion chamber. It has been shown that in case of a hydraulic free piston engine (HFPE), using active motion control, the piston inside the combustion chamber can be forced to track any desired trajectory, despite the absence of a crankshaft, providing reliable starting and stable operation. This allows the use of optimized piston trajectory for every operating point which minimizes fuel consumption and emissions. In this work, this concept is extended to an electrical free piston engine (EFPE) as a modular power source.

Many dual fuel technologies have been proposed for diesel engines. Implementing dual fuel modes can lead to emissions reductions or increased efficiency through using partially premixed combustion and fuel reactivity control. All dual fuel systems have the practical disadvantage that a secondary fuel storage and delivery system must be included. Reforming the primary diesel to a less reactive vaporized fuel on-board has potential to overcome this key disadvantage. Most previous research regarding on-board fuel reforming has been focused on producing significant quantities of hydrogen. However, only partially reforming the primary fuel is sufficient to vaporize and create a less volatile fuel that can be fumigated into an engine intake. At lower conversion efficiency and higher equivalence ratio, reforming reactors retain higher percentage of the inlet fuel’s heating value thus allowing for greater overall engine system efficiency.

Low emission heavy-duty diesel engines are increasingly utilizing four-valve designs with vertical central injectors. However, two-valve DI diesel engines with inclined injectors offset from the centerline of the piston bowl are likely to continue to be used in medium and light duty applications for some time. In such situations, designing of the hole-type nozzle is very difficult and may cause unavoidable back-drilling problems. The purpose of this paper is to solve back-drilling problems connected with hole-type nozzles and improve fuel-air mixing which leads to more efficient combustion. Based on geometric considerations, this paper introduces single-cone hole-type nozzles, double-cone hole-type nozzles, and the critical principal angles for hole-type nozzles. The single-cone hole-type nozzles and double-cone hole-type nozzles can meet requirements for height of the spray impingement points and spray orifice distribution angle at the same time.

A typical means of limiting the peak power output of race car engines is to restrict the maximum mass flow of air to the engine. The Formula SAE sanctioning body requires the use of an intake restrictor to limit performance, keep costs low, and maintain a safe racing experience. The intake restrictor poses a challenge to improving engine performance. Methods to better understand the ramifications of the restrictor on the engine lead to performance improvements that allow an edge over the competition. A one-dimensional gas exchange simulation code coupled with three-dimensional CFD is used to simulate various concepts in the improvement of restrictor performance. Ricardo's WAVE and VECTIS are the respective simulation codes. Along with this, the interaction of intake manifold and restrictor are considered. The effects of different diffuser geometries and plenum dimensions were first explored using WAVE, and then a series of different diffuser angles were simulated using WAVE-VECTIS.

A biodiesel / petroleum fuel blend and practical low-cost methods of emission control were sought to obtain reductions in emissions from diesel generators. Little direct testing of biodiesel in diesel-powered electric generators has been done. Laboratory and field evaluations were conducted to determine the influence of using biodiesel on diesel exhaust emissions. B20 (20% biodiesel / 80% petroleum diesel) was chosen because of previously successful studies with this blend level, and there is evidence that the NOx emissions increase that result from using B20 can be controlled using existing technology. B85 was selected because it is a “high blend,” which promised to give a large decrease in PM at the expense of a larger increase in NOx than B20, but still within the range of control with existing technology. Charge-air cooling and a fuel additive were tested as NOx controls. For PM, CO, and HC reduction, a diesel oxidation catalyst (DOC) was evaluated.

This program used a 0.6 liter DI NA single cylinder diesel engine to study the influence of ferrocene as a fuel additive on particulate and NOx emissions and heat release rates. Previous Studies1,15 have shown efficiency and particulate emission benefits only after engine conditioning. Two engine configurations were tested: standard aluminum piston with normal engine deposits and a second test with the engine cleaned to “new engine condition”, but with the piston replaced with a thermal barrier coated piston. Particle concentration and size in roughly the 7.5 to 750 nm diameter range were measured with a condensation nucleus counter and an electrical aerosol analyzer. Heat release rates and IMEPs were calculated from in-cylinder pressure data. Particle number concentrations increased substantially when the 250 ppm dose was first started with both engine configuration, but decreased 30% to 50% with conditioning.

The formation of particles in the combustion chamber of a direct injection diesel engine has been studied with the use of the Total Cylinder Sampling Method. With this method, nearly the entire contents of the cylinder of an operating diesel engine can be quickly removed at various times during the combustion process. The particle mass and size distributions present in the sample can then be analyzed. If quenching of the combustion process is quick and complete, the resulting samples are representative of the particle mass and size distributions present in the cylinder near the time sampling begins. This paper discusses the effect of injection timing and piston bowl shape on the particle formation and oxidation. Example size distribution measurements are also shown. The particle concentrations in the cylinder were measured for three different injection timings with the standard piston installed in the engine.

A fully flexible valve actuation (FFVA) system was developed for a single cylinder research engine to investigate high efficiency clean combustion (HECC) in a diesel engine. The main objectives of the study were to examine the emissions, performance, and combustion characteristics of the engine using late intake valve closing (LIVC) to determine the benefits and limitations of this strategy to meet Tier 2 Bin 5 NOx requirements without after-treatment. The most significant benefit of LIVC is a reduction in particulates due to the longer ignition delay time and a subsequent reduction in local fuel rich combustion zones. More than a 95% reduction in particulates was observed at some operating conditions. Combustion noise was also reduced at low and medium loads due to slower heat release. Although it is difficult to assess the fuel economy benefits of LIVC using a single cylinder engine, LIVC shows the potential to improve the fuel economy through several approaches.

Previous studies have shown Late Intake Valve Closure (LIVC) through Variable Valve Timing (VVT) to offer reduced fuel consumption through reduced pumping work. Load modulation through the controlled phasing of one of two intake valves/cylinder is one means of accomplishing the LIVC strategy on a multi-valve engine. Experimental studies of LIVC show that cycle-to-cycle variations and reduced flame velocity in single or synchronized multiple intake valve engines are associated with performance which, though superior to throttled engine performance, falls short of its promised fuel economy. To examine if the higher mixture velocity promised by valve phasing relative to single or synchronized LIVC mitigates cycle-to-cycle variations and flame velocity defects, a modification of the Quad 4 engine has been designed and built and is, at the present writing, being tested. The design employs a third camshaft placed above the original intake valve camshaft.