Search Results

The internal mixture formation within SI engines using fuel direct injection has a significant potential regarding the reduction of bsfc and pollutant emission. However the short time available for injection and spray distribution, as well as the complexity of the fluid dynamic conditions, amplified in a wide load and speed range, form a different base for the combustion process than using external mixture formation. The intend of the present study is to develop a method for modeling and optimization of mixture formation and combustion using a general approach for the fuel direct injection, which consist in the modulation of the injection rate, independently on the engine speed. In the first stage of modeling, the optimum combination between mixture formation elements as fuel pressure history, injection timing, spray characteristics, injector location or combustion chamber design is of great importance, forming the conditions for the subsequent combustion process.

The paper presents a concept for modeling and optimization of the mixture formation process during gasoline direct injection, using a high-pressure single fluid injection system which allows the modulation of the injection rate independently on the engine speed. Going from this favorable premise for the adaptation of the mixture formation to various load and speed conditions, the aim of modeling is to find the optimum combination between the adaptable elements as follows: form of the fuel pressure wave, injection timing, spray form, injector location, form of the combustion chamber. Moreover, the interaction between fuel and air flow within the cylinder during the mixture formation is considered as a determining factor for the combustion process, and forms thereby an important part of the modeling.

In order to develop modern two-stroke engines with low fuel consumption, respectively with low exhaust emissions, two alternative development areas - the mixture formation and the scavenging system - have been correlated. For a satisfying mixture formation without fuel losses by scavenging, the direct injection seems to be one of the best solution for the high speed two-stroke engine of the future. On the other hand the modern development of two-stroke scavenging systems shows a large field of application and improvement methods of cross and loop scavenging [1]. Based on the specific optimisation factors of the injection system, respectively of the scavenging system, the aim off this common work of the Universities of Pisa and Zwickau is to correlate both the optimisation fields in an advantageous mixture formation process.

Homogeneous or partially premixed charge compression ignition combustion is considered to be an attractive alternative to traditional internal combustion engine operation because of its extremely low levels of pollutant emissions. However, since it is difficult to control the start of combustion timing, direct injection of fuel into the combustion chamber is often used for combustion phasing control, as well as charge preparation. In this paper, numerical simulations of compression ignition processes using gasoline fuel directly injected using a low pressure, hollow cone injector are presented. The multi-dimensional CFD code, KIVA3V, that incorporates various advanced sub-models and is coupled with CHEMKIN for modeling detailed chemistry, was used for the study. Simulation results of the spray behavior at various injection conditions were validated with available experimental data.

World-wide attention to environmental issues in recent years has resulted in a greater demand for cleaner engines, especially with regards to the two-stroke. Considering the techniques for reduction of exhaust emissions the direct injection of fuel into the combustion chamber adapted for a loop scavenged cylinder seems to be an advantageous method. This paper describes the application of advanced experimental and computational techniques to evaluate mixture formation produced on a commercial engine by means of a direct fuel injection strategy, namely a ram-tuned injection system. The injection system data are experimental while air flow and fuel air mix for the direct injection engine are calculated using a turbulent model of the three dimensional code FLUENT. Extension of a first work in this field is presented. In particular two possible strategies to simulate direct injection are tested. The influence of different boundary conditions on the scavenging process was examined too.

The future development of two-stroke engines will be conditioned by the drastic reduction of pollutant emission, especially of hydrocarbon. This goal is not achievable only by scavenging improvement, rather a new quality of mixture formation using direct injection is imposed. However, the internal mixture formation in a large range of speed and load, considering the scavenge flow particularities of two-stroke engines as well, appears as an extremely complex process. Thereby a numerical simulation is in this case very effective for the adaptation of a direct injection method at the engine. The paper presents a concept for modeling and optimization of the mixture formation process within a high-speed two-stroke engine with liquid fuel injection system. The injection system generates a pressure pulse which is not dependent on the engine speed.

The advantages of internal mixture formation regarding the important reduction of fuel consumption, respectively of the pollutant emission determined in the last years an intensive development of direct injection concepts. Superimposing the potential of direct injection with the advantages of ethanol concerning the availability and partial CO2 re-circulation, there appears to be an advantageous scenario for the future of SI engines. The paper presents a direct injection system with high pressure modulation which is able to operate with different ratios of gasoline/ethanol mixture. The paper presents furthermore a concept for modeling and optimization of the mixture formation process in the case of gasoline / ethanol direct injection.