Search Results

A computer program which rapidly calculates the equilibrium mole fractions and the partial derivatives of the mole fractions with respect to temperature, pressure and equivalence ratio for the products of combustion of any hydrocarbon fuel and air is described. A subroutine is also given which calculates the gas constant, enthalpy, internal energy and the partial derivatives of these with respect to temperature, pressure and equivalence ratio. Some examples of the uses of the programs are also given.

Fine-wire resistance thermometers were used to measure compression gas temperatures in a motoring (nonfiring) cycle CFR engine. Temperature versus crankangle curves were obtained for the compression and expansion strokes by means of tungsten wires ranging in diameter from 0.15–1.00 mils and at speeds from 600–1800 rpm. The results were compared with the infrared pyrometer; the peak temperature and peak crankangle lags were determined as a function of the wire diameter and engine speed. Attempts to evaluate the instantaneous energy balance around the wire resulted in a negative heat transfer coefficient, for which no current satisfactory explanation is available, although other observers have reported similar phenomena. The tungsten resistance thermometer is simple to build, easy to install, and requires no modification of the engine block for use during motoring. Thus, it is suitable for comparing the compression temperatures of different design engines.

Cycle-to-cycle variation in combustion phasing and combustion rate cause knock to occur differently in every cycle. This is found to be true even if the end gas thermo-chemical time history is the same. Three cycles are shown that have matched combustion phasing, combustion rate, and time of knock onset, but have knock intensity that differs by a factor of six. Thus, the prediction of knock intensity must include a stochastic component. It is shown that there is a relationship between the maximum possible knock intensity and the unburned fuel energy at the time of knock onset. Further, for a small window of unburned energy at knock onset, the probability density function of knock intensity is self similar when scaled by the 95th percentile of the cumulative distribution, and log-normal in shape.

Modeling ignition kernel development in spark ignition engines is crucial to capturing the sources of cyclic variability, both with RANS and LES simulations. Appropriate kernel modeling must ensure that energy transfer from the electrodes to the gas phase has the correct timing, rate and locations, until the flame surface is large enough to be represented on the mesh by the G-Equation level-set method. However, in most kernel models, geometric details driving kernel growth are missing: either because it is described as Lagrangian particles, or because its development is simplified, i.e., down to multiple spherical flames. This paper covers the geometric aspects of kernel development, which makes up the core of a Triangulated Lagrangian Ignition Kernel model. One (or multiple, if it restrikes) spark channel is initialized as a one-dimensional Lagrangian particle thread.

Simultaneous measurements of the radial and the tangential components of velocity are obtained in a high-speed, direct-injection diesel engine typical of automotive applications. Results are presented for engine operation with fuel injection, but without combustion, for three different swirl ratios and four injection pressures. With the mean and fluctuating velocities, the r-θ plane shear stress and the mean flow gradients are obtained. Longitudinal and transverse length scales are also estimated via Taylor's hypothesis. The flow is shown to be sufficiently homogeneous and stationary to obtain meaningful length scale estimates. Concurrently, the flow and injection processes are simulated with KIVA-3V employing a RNG k-ε turbulence model. The measured turbulent kinetic energy k, r-θ plane mean strain rates ( 〈Srθ〉, 〈Srr〉, and 〈Sθθ〉 ), deviatoric turbulent stresses , and the r-θ plane turbulence production terms are compared directly to the simulated results.

THIS paper is a sequel of the paper, “Photo-Electric Combustion Analysis,” presented at the 1936 Semi-Annual Meeting of the Society. The indicator described in that paper has been used to study combustion of 28 fuels and chemicals. A complete table of information of the materials used as fuels is included. The results obtained from over 1000 oscillograms show a different shape of ignition-lag curve versus injection advance angle than it is ordinarily thought to have. Even though the cetane values for these 28 fuels varied from 24 to 100, they all had nearly the same ignition lag when injected near the dead-center position. This minimum value is shown to be about 1/1000 sec. The fuels of higher-cetane value reach this minimum at an earlier injection angle than do those of low-cetane value. The paper shows how a high-cetane fuel can be just as rough as a low-cetane fuel if the injection timing is too early.

Cylinder liners exert a major influence on engine performance, reliability, durability and maintenance. Various combinations of nonmetallic reinforcements and coatings have been used to improve the tribological performance of sleeves or surfaces used in compressors and internal combustion engines in four stroke, two stroke and rotary configurations. In this paper we report the use of a hybrid composite containing silicon carbide and graphite in an aluminum alloy matrix to improve the performance of various small engines and compressors. Material properties of the base material, as well as comparative dynamometer testing, are presented.

THIS paper discusses a method of measuring compression temperature by means of the absorption of light. An optical-electronic system measures the change in color of a trace of iodine gas that has been added to the intake mixture. From these measurements the temperature of the iodine and by inference, the temperature of the gases, is determined. The apparatus used is described briefly and the test results obtained in measuring compression and end-gas temperatures in a spark-ignition engine are also presented.

An overview of a design methodology based on finite element and fatigue analyses is described for the design of welded structures. Fatigue life is a primary design consideration for agricultural equipment structural members. The re-design of an agricultural implement frame and hitch assembly is used to illustrate the methodology for optimal design and improved fatigue life. A description of the finite element mode of the agricultural implement and the simulated loading history are described. Results from finite element analysis are used to optimize the frame member sizes and calculate the fatigue strength characteristics. This design analysis strategy provides improved fatigue life characteristics for the implement frame or welded structure.

In Equation 10, there should be a plus sign between the first summation term and the quantity in brackets. The acceleration of the participant's vehicle was varied from −0.04 m/s2 to +0.06 m/s2 linearly as a function of the angle of the gas pedal with a 0.1-second delay.

The infrared radiation method of compression and end-gas temperature measurement was applied to the problem of measuring gas temperatures up to the time of knock. Pressure data were taken for each run on a CFR engine with mixtures of isooctane and n-heptane under both knocking and nonknocking conditions. Main engine parameters studied were the intake pressure, intake temperature, and engine speed. The rate and extent of chemical energy release were calculated from the temperature and pressure histories using an energy balance. The computed rates of chemical energy release were correlated to a chain-type kinetic model

A NEW electronic circuit arrangement added to the electro-optical pyrometer developed at the University of Wisconsin indicates instantaneously the temperature in the combustion chamber of a diesel engine. The electronic device, which is described in this paper, solves an equation relating true temperature to intensity and wave length of monochromatic radiation from a luminous flame. True flame temperature is charted on an oscillograph as a function of such abscissas as time or crank angle. Several circuits are reviewed which were found unsuited for use with the pyrometer but which may be useful for other applications.

AN analysis of phenomena occurring during the ignition delay period is presented. Vaporization of atomized fuel is shown to take place under conditions ranging between single droplet and adiabatic saturation from edge to center of the spray. Mechanisms of vaporization and combustible mixture formation are presented for both cases. Correlation of theoretical analysis with experimental data from both a combustion bomb and diesel engine is presented to establish actual conditions existing during vaporization. Estimates of physical and chemical delays for the engine and bomb are given.

The CFD tools in aerodynamic design process have been commonly used in aerospace industry in last three decades. Although there are many CFD software algorithms developed for aerodynamic applications, the nature of a complex, three-dimensional geometry in incompressible highly separated, viscous flow made computational simulation of ground vehicle aerodynamics more difficult than aerospace applications. However, recent developments in computational hardware and software industry enabled many new engineering applications on computational environment. Traditional production process has largely influenced by computational design, analysis, manufacturing and visualization. Different aspects of linking advanced computational tools and aerodynamic vehicle design challenges are discussed in the present work. Key technologies like parallel computation, turbulence modeling and CFD/wind tunnel compatibility issues are presented.

The performance of a structural design significantly depends upon the assumptions made on input load. In order to estimate the input load, during the design and development stage of the suspension assembly of a BAJA car, designers and analysts invest immense amount of time and effort to formulate the mathematical model of the design. These theoretical formulations may include idealization errors which can affect the performance of the car as a final product. Due to the errors associated with the assumption of design load, several components might have more weight or may have less strength than needed. This discrepancy between the assumed input load (lab or theoretical studies) and the actual load from the environment can be eliminated by performing a real life testing process using load recovery methodology. Commercial load cells exist in industry to give engineers insight to understanding the complex real world loading of their structures.

Knock in a Rotax-914 engine was modeled and investigated using an improved version of the KIVA-3V code with a G-equation combustion model, together with a reduced chemical kinetics model. The ERC-PRF mechanism with 47 species and 132 reactions [1] was adopted to model the end gas auto-ignition in front of the flame front. The model was validated by a Caterpillar SI engine and a Rotax-914 engine in different operating conditions. The simulation results agree well with available experimental results. A new engineering quantified knock criterion based on chemical mechanism was then proposed. Hydroperoxyl radical (HO2) shows obvious accumulation before auto-ignition and a sudden decrease after auto-ignition. These properties are considered to be a good capability for HO2 to investigate engine knock problems.

The three-dimensional CFD codes KIVA-II and KIVA-3 have been used together to study the effects of intake generated in-cylinder flow structure on fuel-air mixing and combustion in a direct injected (DI) Diesel engine. In order to more accurately account for the effect of intake flow on in-cylinder processes, the KIVA-II code has been modified to allow for the use of data from other CFD codes as initial conditions. Simulation of the intake and compression strokes in a heavy-duty four-stroke DI Diesel engine has been carried out using KIVA-3. Flow quantities and thermodynamic field information were then mapped into a computational grid in KIVA-II for use in the study of mixing and combustion. A laminar and turbulent timescale combustion model, as well as advanced spray models, including wave breakup atomization, dynamic drop drag, and spray-wall interaction has been used in KIVA-II.

The effects of imaging system resolution and laser sheet thickness on the measurement of the Batchelor scale were investigated in a single-cylinder optical engine. The Batchelor scale was determined by fitting a model spectrum to the dissipation spectrum that was obtained from fuel tracer planar laser-induced fluorescence (PLIF) images of the in-cylinder scalar field. The imaging system resolution was quantified by measuring the step-response function; the scanning knife edge technique was used to measure the 10-90% clip width of the laser sheet. In these experiments, the spatial resolution varied from a native resolution of 32.0 μm to 137.4 μm, and the laser sheet thickness ranged from 108 μm to 707 μm. Thus, the overall resolution of the imaging system was made to vary by approximately a factor of four in the in-plane dimension and a factor of six in the out-of-plane dimension.

THE PRESENT WORK uses both the hot-motored technique and a nitrogen technique to obtain three pressure-time records — one without either vaporization or chemical reaction, one with vaporization only, and one with both vaporization and chemical reaction. By comparison of these three records, rates of vaporization and rates of chemical reaction can be determined during the ignition delay period in an operating diesel engine. Such data are shown for different fuels and operating conditions. Estimations are made of the penetration and temperatures existing in the spray.*

To model sprays from pressure-swirl atomizers, the connection between the injector and the downstream spray must be considered. A new model for pressure-swirl atomizers is presented which assumes little knowledge of the internal details of the injector, but instead uses available observations of external spray characteristics. First, a correlation for the exit velocity at the injector exit is used to define the liquid film thickness. Next, the film must be modeled as it becomes a thin, liquid sheet and breaks up, forming ligaments and droplets. A linearized instability analysis of the breakup of a viscous, liquid sheet is used as part of the spray boundary condition. The spray angle is estimated from spray photographs and patternator data. A mass averaged spray angle is calculated from the patternator data and used in some of the calculations.