Search Results

In an attempt to reach a compromise between the views of environmentalists and snowmobile enthusiasts, the University of Wisconsin-Madison Clean Snowmobile Team set out to design a machine that maintains performance while decreasing air and noise pollution. After careful consideration of all possible design avenues, the decision was made to select a four-stroke power plant. In order to optimize the engine's efficiency, an engine control unit was chosen that was both capable and affordable. Engine modifications were made to allow the snowmobile's stock transmission to be used. Alterations were also made to intake, exhaust, and cooling systems to allow the engine to fit comfortably under the snowmobile's stock hood. Modifications were made to the snowmobile's chassis to accommodate the additional mass associated with the four-stroke engine. The final product is a snowmobile that minimizes environmental impact but still has the appearance and performance necessary to satisfy consumers.

The use of virtual prototyping early in the design stage of a product has gained popularity due to reduced cost and time to market. The state of the art in vehicle simulation has reached a level where full vehicles are analyzed through simulation but major difficulties continue to be present in interfacing the vehicle model with accurate powertrain models and in developing adequate formulations for the contact between tire and terrain (specifically, scenarios such as tire sliding on ice and rolling on sand or other very deformable surfaces). The proposed work focuses on developing a ground vehicle simulation capability by combining several third party packages for vehicle simulation, tire simulation, and powertrain simulation. The long-term goal of this project consists in promoting the Digital Car idea through the development of a reliable and robust simulation capability that will enhance the understanding and control of off-road vehicle performance.

The paper describes a methodology to co-simulate, with high fidelity, simultaneously and in one computational framework, all of the main vehicle subsystems for improved engineering design. The co-simulation based approach integrates in MATLAB/Simulink a physics-based tire model with high fidelity vehicle dynamics model and an accurate powertrain model allowing insights into 1) how the dynamics of a vehicle affect fuel consumption, quality of emission and vehicle control strategies and 2) how the choice of powertrain systems influence the dynamics of the vehicle; for instance how the variations in drive shaft torque affects vehicle handling, the maximum achievable acceleration of the vehicle, etc. The goal of developing this co-simulation framework is to capture the interaction between powertrain and rest of the vehicle in order to better predict, through simulation, the overall dynamics of the vehicle.

In this paper, a comparative study of the production applications of hybrid electric powertrains is presented. Vehicles studied include the Toyota Prius, Honda Insight, Toyota Estima, Toyota Crown, Honda Civic Hybrid, and Nissan Tino. The upcoming Ford Escape Hybrid and General Motors Parallel Hybrid Truck (PHT) will also be included, although advance information is limited. The goal of this paper is to look at what hybrid drivetrain architectures have actually been selected for production and what are the underlying details of these drivetrains. Since hybridizing a powertrain involves significant changes, the powertrain architectures are presented in diagram form, with analysis as to the similarities and advantages represented in these architectures. The specific hybrid functions used to save fuel are discussed. Peak power-to-weight ratio and degree of hybridization are plotted for the vehicles. System voltage versus electric power level are also plotted and analyzed.

A system was developed which provides nutrients and water to plants while maintaining good aeration at the roots and preventing water from escaping in reduced gravity. The nutrient solution is circulated through porous tubes under negative pressure and moves through the tube wall via capillary forces into the rooting matrix, establishing a non-saturated condition in the root zone. Tests using prototypes of the porous tube water and nutrient delivery system indicate that plant productivity in this system is equivalent to standard soil and solution culture growing procedures. The system has functioned successfully in short-term microgravity during parabolic flight tests and will be flown on the space shuttle. Plants are one of the components of a bioregenerative life support system required for long duration space missions.

The need for improved emissions control in lean exhaust to meet tightening, world-wide NOx emissions standards has led to the development of selective catalytic reduction of NOx with ammonia as a major technology for emissions control. Current systems are being designed to use a solution of urea (32.5 wt %) dissolved in water or Diesel Exhaust Fluid (DEF) as the ammonia source. While DEF or AdBlue® is widely used as a source of ammonia, it has a number of issues at low temperatures, including freezing below −12 °C, solid deposit formation in the exhaust, and difficulties in dosing at exhaust temperatures below 200 °C. Additionally creating a uniform ammonia concentration can be problematic, complicating exhaust packaging and usually requiring a discrete mixer.

The paper describes the development of a vehicle stability indicator based on the correlation between various current vehicle chassis sensors such as hand wheel angle, yaw rate and lateral acceleration. In general, there is a correlation between various pairs of sensor signals when the vehicle operation is linear and stable and a lack of correlation when the vehicle is becoming unstable or operating in a nonlinear region. The paper outlines one potential embodiment of the technology that makes use of the Mahalanobis distance metric to assess the degree of correlation among the sensor signals. With this approach a single scalar metric provides an accurate indication of vehicle stability.

This paper presents the development of coordinated control of vehicle systems, specifically for controlled brakes and controlled steering systems. By utilizing a control structure to oversee a four-wheel-steer (4WS) system and a brake-based vehicle stability enhancement (VSE) system, it is possible to achieve improvements in vehicle stability and driver workload/comfort, and to reduce compromises in vehicle handling. The coordinated control is designed to leverage the unique strengths of 4WS and VSE, and to prevent conflicts between them. Vehicle test results prove the viability of the concept.

Among the performance concerns in brake design, drag and fluid displacement are getting more attention in the requirement definition. High drag not only affects fuel efficiency and lining life, it is also a contributing factor to rotor thickness variation and brake pulsation. In this paper, a system approach to drag performance of a disc brake caliper is presented. A one-dimensional simulation model, which considers all the significant factors, including lining stiffness and hysteresis, housing stiffness, seal/groove characteristic, and stick-slide behavior between the seal and piston, is developed to capture the interactive impact of each parameter to caliper drag performance. The system model is validated with experimental measurements for caliper fluid displacement and piston retraction. A parameter study is then conducted to investigate the component interactive impact to the drag performance.

Identifying edge cases for designed algorithms is critical for functional safety in autonomous driving deployment. In order to find the feasible boundary of designed algorithms, simulations are heavily used. However, simulations for autonomous driving validation are expensive due to the requirement of visual rendering, physical simulation, and AI agents. In this case, common sampling techniques, such as Monte Carlo Sampling, become computationally expensive due to their sample inefficiency. To improve sample efficiency and minimize the number of simulations, we propose a tailored active learning approach combining the Support Vector Machine (SVM) and the Gaussian Process Regressor (GPR). The SVM learns the feasible boundary iteratively with a new sampling point via active learning. Active Learning is achieved by using the information of the decision boundary of the current SVM and the uncertainty metric calculated by the GPR.

In this paper, we review existing software safety standards, guidelines, and other software safety documents. Common software safety elements from these documents are identified. We then describe an adaptable software safety process for automotive safety-critical systems based on these common elements. The process specifies high-level requirements and recommended methods for satisfying the requirements. In addition, we describe how the proposed process may be integrated into a proposed system safety process, and how it may be integrated with an existing software development process.

Anti-Lock Brake Systems use hydraulic valves to control brake pressure and ultimately, wheel slip. The difference in pressure across these hydraulic valves affects their performance. The control of these valves can be improved if the pressure difference is known and the valve control altered accordingly. In practice, the delta- pressure is estimated. Estimating the wheel brake pressure introduces an error into the control structure of the system, i.e. the difference between the actual wheel brake pressure and the estimated wheel brake pressure. The effect of this error was investigated at the vehicle level via simulation, using stopping distance and vehicle yaw rate as evaluation criteria. Even with large errors in the brake pressure estimate, it was found that the vehicle performance was largely unaffected.

A new technique which is based on optoacoustic phenomena has been developed for measuring in-cylinder gas temperature and turbulent diffusivity. In the experiments, a high energy Nd:YAG pulsed laser beam was focused to cause local ionization of air at a point in the combustion chamber. This initiates a shock wave and creates a hot spot. The local temperature and turbulent diffusivity are determined by monitoring the shock propagation and the hot spot growth, respectively, with a schlieren photography system. In order to assess the validity and accuracy of the measurements, the technique was also applied to a turbulent jet. The temperature measurements were found to be accurate to within 3%. Results from the turbulent jet measurements also showed that the growth rate of the hot spot diameter can be used to estimate the turbulent diffusivity. In-cylinder gas temperature measurements were made in a motored single cylinder Caterpillar diesel engine, modified for optical access.

We present an approach in which an open-source software infrastructure is used for testing the behavior of autonomous vehicles through computer simulation. This software infrastructure is called CAVE, from Connected Autonomous Vehicle Emulator. As a software platform that allows rapid, low-cost and risk-free testing of novel designs, methods and software components, CAVE accelerates and democratizes research and development activities in the field of autonomous navigation.

Fundamental simulations using DNS type procedures were used to investigate the ignition, combustion characteristics and the lift-off trends of a spatially evolving turbulent liquid fuel jet. In particular, the spatially evolving n-Heptane spray injected in a two-dimensional rectangular domain with an engine like environment was investigated. The computational results were compared to the experimental observations from an optical engine as reported in the literature. It was found that an initial fuel rich combustion downstream of the spray tip is followed by diffusion combustion. Investigations were also made to understand the effects of injection velocity, ambient temperature and the droplet radius on the lift-off length. For each of these parameters three different values in a given range were chosen. For both injection velocity and droplet radius, an increase resulted in a near linear increase in the lift-off length.

In occupant sensing system development, the Anthropomorphic Test Dummy (ATD) and the Occupant Classification ATD (OCATD) are frequently used to simulate live human subjects in the testing and validation of weight based occupant sensing systems. A study was conducted to investigate the range of loading differences between these ATDs and live human subjects over various seating postures and conditions. The results of the study revealed that differences in seat load patterns could be significant, even though both the ATD and live humans are in the same weight and body size categories. Seat loading was measured using Hybrid III (5th percentile female, 50th percentile male, and 3 year old) ATDs, OCATDs (OCATD5 - 5th percentile female, and OCATD6 - 6 yr old child), and a CRABI (12-month old) dummy. Human subjects in the same weight and height categories as the above listed ATDs were also measured.

Two soot-containing turbulent non-premixed flames burning gaseous acetylene in atmospheric-pressure air were investigated by conducting non-intrusive optical experiments at various flame locations. The differences in burner exit Reynolds numbers of these flames were large enough to examine the influence of flow dynamics on soot formation and evolution processes in heavily-sooting flames. By accounting for the fractal nature of aggregated primary particles (spherules), the proper interpretation of the laser scattering and extinction measurements yielded all the soot parameters of principal interest. With the separation of spherule and aggregate sizes, the axial zones of the prevailing turbulent soot mechanisms were accurately identified. With the high propensity of acetylene fuel to soot, relatively fast particle nucleation process led to high concentrations immediately above the burner exit.

The ASTROCULTURE™ (ASC) middeck flight experiment series was developed to test and integrate subsystems required to grow plants in reduced gravity, with the goal of developing a plant growth unit suitable for conducting quality biological research in microgravity. Flights on the Space Shuttle have demonstrated control of water movement through a particulate rooting material, growth chamber temperature and humidity control, LED lighting systems and control, recycling of recovered condensate, ethylene scrubbing, and carbon dioxide control. A complete plant growth unit was tested on STS-63 in February 1995, the first ASC flight in which plant biology experiments were conducted in microgravity. The methods and objectives used for control of environmental conditions in the ASC unit are described in this paper.

In this paper a method of mitigating the consequences of potential brake actuator failure in vehicles with brake-by-wire (BBW) and possibly with steer-by-wire (SBW) systems is described. The proposed control algorithm is based on rules derived from general principles of vehicle dynamics. When a failure of one actuator is detected, the algorithm redistributes the braking forces among the remaining actuators in such a way that the desired deceleration of vehicle is followed as closely as possible, while the magnitude and the rate of change of the yaw moment caused by asymmetric braking are properly managed. When vehicle is equipped with BBW system only, or when the desired deceleration can be obtained by redistributing of braking forces, without generating an undesired yaw moment, no steering correction is used. Otherwise, a combination of brake force redistribution and steering correction (to counter the yaw moment generated by non-symmetric braking) is applied.

Embedded controllers and digital signal processors are increasingly being used in automotive safety critical control systems. Controller integrity is a significant concern in these systems. Over the past decade, several techniques have been published about controller safety and integrity verification. These techniques include: single processor with watchdog, dual processors, dual core processor, and asymmetric processor (intelligent watchdog). Each of these techniques have benefits, however, many new non-distributed safety-critical systems are applying the asymmetric processor technique to help verify controller integrity. This paper discusses an overview of five controller integrity techniques, and then provides a detailed discussion of an asymmetric processor approach. This paper presents two different options within the asymmetric processor approach.