Search Results

Engine mounts are an integral part of the vehicle that helps in reducing the vibrations generated from the engine. Engine mounts require a simple yet complicated amalgamation of two very different materials, steel and rubber. Proper adhesion between the two is required to prevent any part failure. Therefore, it becomes important that a comprehensive study is done to understand the mating phenomenon of both. A good linking between rubber and metal substrate is governed by surface pretreatment. Various methodologies such as mechanical and chemical are adopted for the same. This paper aims to present a comparative study as to which surface pretreatment has an edge over other techniques in terms of separation force required to break the bonding between the two parts. The study also presents a cost comparison between the techniques so that the best possible technique can be put to use in the commercial vehicle industry.

Euro 6 emission norms are getting implemented in India from April 2020 and it is being viewed as one of the greatest challenges ever faced by the Indian automotive industry. In order to achieve such stringent emission norms along with top performance for vehicle, a good strategy should be incorporated to control system out NOx emissions and soot regeneration. Extruded Vanadium catalyst is deployed for this passive regeneration system with DOC (Diesel Oxidation Catalyst), DPF (Diesel Particulate Filter) and SCR (Selective Catalyst Reduction), where the amount of catalyst loading in DOC plays an apex role in deciding conversion efficiency of SCR and passive regeneration capabilities. This study mainly focuses on the impact of catalyst loading of DOC over SCR efficiency. NO2 to NOx ratio should be close to 0.5 for optimum conversion efficiency of SCR. Catalyst loading in DOC decides the amount of NO2 coming upstream to SCR.

Euro 6 emission norms are getting implemented in India from April 2020 and it is being viewed as one of the greatest challenges ever faced by the Indian automotive industry. In order to achieve such stringent emission norms a good strategy will be to optimize the engine out emission through in cylinder emission control techniques and a right sized after treatment system has to be used for this optimized engine. There exist several factors and trade-off between these should be established for in cylinder optimization of emissions. Since the turbocharger plays an apex role in controlling both the performance and engine out emissions of a CI engine, turbocharger selection is a crucial step in the development of new generation of Euro 6 engines in India. Such engines are equipped with additional actuators such as Intake Throttle Valve and Exhaust Throttle Valve and combination of these flap operations with turbocharger output plays a prominent role in controlling performance and emission.

The air purifier industry has seen a growth in terms of demand and sales lately. All credit goes to massive Industrialization in developing countries such as India. The most harmful of the pollutants are PM 2.5 articulates and NOx Emissions. This leads to the new trend of customers become health and comfort conscious and willing to pay more for better and improved transportation. To satisfy these demands, COEM’s are developing more numbers of Air conditioning buses. Although the OEM’s are meeting this demand of quantity, the quality of air from air conditioner is still suffer. One of the main reasons for this poor air quality is because of the ineffectiveness of conventional air conditioner air filters to control particulate materials i.e. PM2.5, biological pollutants i.e. microbes, bacteria, viruses, and gaseous pollutants i.e. CO, CO2, SO2, NOX, O3 & VOCs in air. As per various researches, health problems associated with bus occupant compartment air quality appear more frequently.

Overall cycle time and prototype testing are significantly decreased by assessment of cooling module performance in the design stage itself. Hence, Front End Cooling and Thermal Management are essential components of the vehicle design process. Performance of the cooling module depends upon a variety of factors like frontal opening, air flow, under-hood sub-systems, module positioning, front grill design, fan operation. Effects of design modifications on the engine cooling performance are quantified by utilizing computational fluid dynamics (CFD) tool FluentTM. Vehicle frontal configuration is captured in the FE model considering cabin, cargo and underbody components. Heat Exchanger module is modelled as a porous medium to simulate the fluid flow. Performance data for the Heat Exchanger module is generated using the 1D KuliTM software. In this paper, CFD simulation of Front End Cooling is performed for maximum torque and maximum power operating conditions.

In an electric vehicle, engine is replaced with battery and transmission is replaced with traction motor. Thermal management of electric battery and motor became a necessary evaluation step in the design and development process of electric vehicles. The temperature of the traction motor coolant is required to be maintained below 600C to ensure proper functioning of the system. Coolant takes away heat from traction motor, motor controller along with an on-board charger in battery charging and discharging conditions. In this paper the cooling unit selection for the total required heat rejection from all three components is analytically calculated and thermal management methodology of liquid-cooled Electric Motor is being studied and documented with the help of numerical simulation. The results are further validated with test results in Electric bus for city application.

For the upcoming norms of BSVI, it is very important to keep the balance of emission and fuel economy. In these paper different concepts for exhaust gas temperature management will be analyzed and compared. In transient and steady conditions with medium and low load, the effects of active control strategies on exhaust thermal management were studied at the test bench, which include E waste gate intake throttle valve opening, injection advance angle, injection pressure and post injection. The comparison study was factors impacting the fuel economy and temperature management along with to meet WHSC & WHTC emission. The DOE was done to understand the best suitable match with the above function to achieve the optimized fuel economy and BSVI legislative requirement. Different test where carried with 0-100% of opening of intake throttle valve, E waste full open and late post injection to understand the thermal management of engine in part and full load.

To compete with the current market trends there is always a need to arrive at a cost effective and light weight designs. For commercial vehicles, an attempt is made to decrease weight of the current design without compromising its strength & stiffness, considering/bearing all the worst road/engine load cases and severe environmental conditions. The topic was chosen because of interest in higher payloads, lower weight, and higher efficiency. Automotive cylinder head must be lighter in weight, to meet increasingly demanding customer requirements. The design approach for cylinder head has made it difficult to achieve this target. A designer might make some judgment as to where ribs are required to provide stiffness, but this is based on engineering experience and Finite Element Analysis (FEA) of the stand-alone head.

The diesel oxidation catalyst (DOC) is one of the major components of a diesel after treatment system. Earlier, DOCs were majorly used to oxidise un-burnt HC and CO from the exhaust gas to keep these pollutants within legislation limits. As legislative norms evolved towards becoming more stringent, the technology and chemistry of after-treatment catalysts have also advanced simultaneously. For Diesel Engines to meet BSVI emission norm, the DOC has a vital role to play. Apart from oxidizing un-burnt THC and CO, now it has to perform additional functions of converting NOx to NO2 to achieve desired NO2/NOx ratio for better DeNOx in the SCR and also give efficient exotherm across it when the cat burner fuel is injected during DPF Regeneration with minimal HC slip. In this paper, two DOCs having different PGM loadings and volumes are evaluated for their exothermal efficiencies and corresponding THC slips.

Turbo lag is a very common phenomenon with all diesel engines using the turbo charger to boost power output from an engine. Naturally aspirated diesel engine which is more polluting, heavier, having higher power losses makes a diesel engine more lethargic. Turbocharged diesel engine is fuel efficient, having lower emissions and better power. A smaller sized turbocharged diesel engine delivers power equivalent to larger sized engine; Turbo Lag is the time required to change power output in response to throttle inputs. Turbo lag results in slow increase of speed when we press the accelerator pedal. Turbo lag becomes a real cause of concern when rapid changes in power are required. This is due to the time required for a turbocharger and exhaust system to generate the required boost.

The hybrid structure of Engine Mounts made of rubber casing with cast iron reinforcing. Use of two materials made it unique both in application and testing. The rubber provides damping for engine vibrations and the cast iron provides necessary strengthening to hold the heavy engine in place. In this research paper the FEA (Finite Element Method) methodology is being discussed to evaluate and optimize the design analysis to enhance overall engine mount capacity. The existing and modified designs are validated and considerable improvement is being observed in modified design in physical testing. Accurate modeling of engine mounts assembly is presented in this paper. FEA analysis results have good correlation with physical validation for both designs. Impact of design parameters of rubber mounts has been presented.

An engine cooling system is required to maintain stable operating temperature for the engine and prevent it from overheating. Thermal distortion of engine parts can take place if proper cooling is not maintained and engine may loss efficiency. One of the major problem in this domain is to incorporate separate cooling systems for the different variants of engines (different power rating). A single optimized cooling unit is desired to manage the entire range of engine rated power. The factors that affect the cooling system are front end grill opening area, air recirculation, location of snorkel inlet, radiator core size, which need to be tuned to get appropriate results. The above parameters are tuned to obtain appropriate results using the Computational Fluid Dynamics (CFD) simulations. In the next stage, on road cooling trials are performed and real time data is collected.

The existing head cover is having external oil and blow by separation unit, which is not only costlier but also complex and leads to increase in overall height of engine which was difficult to integrate in new variants of vehicles. A new head cover has been designed with internal baffle type oil and blow by separation system to ensure efficient separation and proper packaging of the system in new variants. The new system has been finalized after 26 DOE’s of different wire mesh sizes and different baffle plate size and positions. The final system has two bowl shaped separation unit with wire mesh, two cup type oil separation passages and one baffle plate for separating blow by. The system works on condensation and gravity method. The blow by is guided through a well-defined passage integrated in aluminum cylinder head cover itself. The passage angle is maintained to ensure minimum oil flow with blow by.

The urea NOx selective catalytic reduction (SCR) is an effective technique for the reduction of NOx emitted from diesel engines. Urea spray quality has significant effect on NOx conversion efficiency. Air less injection is one of effective, less complex way of injecting urea spray into the Exhaust stream. Further with air less injection it become more challenging in an engine platform of ~3 to 4L where Exhaust mass flow and temperature are relatively less. The droplet diameter and velocity distribution of De-Nox system has taken as input along with Engine raw emission data for a numerical model. The atomization and evaporation of airless urea injection systems were modeled using computational fluid dynamics. The numerical model was validated by the experimental results.

Diesel engines have always been popular for their low end torque and lugging abilities. With their higher thermal efficiencies through technical advancements, diesel engines are preferred powertrains in mass transportation of goods as well as people [14] [15]. A diesel engine always banks on excess air, which is subjected to higher compression ratios so as to achieve temperatures, enough to facilitate auto-ignition of diesel. With the advent of turbocharging and intercooling, the air availability is further enhanced, ensuring better combustion efficiency, lesser HC, CO and particulate matter (PM) emissions together with improved fuel efficiencies [2] [15]. Higher air availability also has its own shortcomings in the form of higher NOx (Nitrogen oxides) emissions. With stringent emission norms in place, reduction of NOx as well as PM, without sacrificing performance and fuel economy, is of utmost importance.

Diesel engines are facing stringent norms and future survival with its lower availability is one of the biggest concerns for OEMs of heavy duty commercial vehicles. This is leading to uplifting of new, latent and innovative techniques to achieve these norms with best possible BSFC to reduce overall diesel consumption. The prime objective of this study is to identify and explore the latent strength of pre and post injection on engine performance, emissions and oil dilution due to soot. The post injection strategy has the potential to reduce soot with almost same NOx and fuel consumption depending on the delay of post injection and its quantity. It aids to increase the engine out temperatures for assistance of after-treatment devices, thus meeting higher temperature requirements for NOx and PM conversion for stringent norms of BSVI.

Future emissions regulations like BSIV and above in India, Diesel engine manufacturers are forced to find complex ways to reduce exhaust gas pollutant emissions, in particular NOx and particulate matter (PM). Exhaust gas recirculation (EGR) into the engine intake is an established technology to reduce NOx emissions. The distribution of EGR in each cylinder plays vital role in combustion process and hence it will affect exhaust emissions. The influence of EGR mixture design and its effect on distribution across the cylinder has significant impact on the NOx-PM trade-off which is studied on light duty direct injection diesel engine. A simulation and experimental study of EGR mixer design is conducted to explain this effect and the distribution of EGR across the cylinder at different EGR flow rate.

Exhaust gas recirculation (EGR) is one of the most effective methods for reducing the emissions of nitrogen oxides (NOx) of diesel engines. EGR system has already been used to mass-produce diesel engines, in which EGR is used at the low and medium load of engine operating condition, resulting in NOx reduction. In order to meet future emission standards, EGR must be done over wider range of engine operation, and heavier EGR rate will be needed. It is especially important for EGR to be done in a high engine load range since the amount of NOx is larger than the other engine operation conditions. EGR systems adapted to the diesel engines of trucks usually recirculate exhaust gas utilizing the pressure difference between upstream part of the turbocharger turbine and downstream part of the compressor. The venturi throat diameter plays the vital role for the flow of EGR across the exhaust and intake.

The new idea discussed in this paper pertains to the carrier mechanism for spare wheels in heavy commercial vehicles. Typically, these vehicles are equipped with a spare wheel carrier featuring a rope mechanism for loading and unloading the spare wheel. The conventional placement of this system is on the side of the frame/chassis or within the limits of the side member. However, the tire-changing process in this system is often arduous, time-consuming, and requires significant effort. The proposed invention addresses these challenges by repositioning the spare wheel to a vertical orientation, facilitating easier access to its bolts and simplifying the removal process from the mountings. Furthermore, the innovation incorporates a three-way actuation system (Air Actuated, Electric motor-driven, or Hydraulic cylinder actuated mechanisms), thereby reducing the need for manual effort and enhancing driver comfort.

The discussed invention is centered on the evaporative cooling of a vehicle cabin, introducing a novel concept of humidity control. Unlike conventional Air Conditioning (AC) systems that operate on the Vapor Compression Refrigeration Cycle (VCRC), which tend to be costly and contribute to higher fuel consumption due to the engine-driven compressor in automobiles, there is currently no other Original Equipment Manufacturer (OEM) fitted cabin cooling option available to address this issue. This paper introduces the idea of a humidity-controlled evaporative cooler. The objective of humidity control is achieved through a controller unit that receives feedback from a humidity sensor, subsequently regulating the operation of the water pump. The ambient air is passed through a humidified honeycomb pad, cooling through the principle of evaporation. To prevent any leftover water droplets from entering the cabin, a polyester nonwoven filter has been integrated into the system.