Search Results

Aluminum-based metal matrix composites are continuously changing to meet the industry’s specialized needs. In the aluminum alloy series, the AA5052 had a lightweight, high strength, good weldability, excellent corrosion resistance, and a good surface finish during the machining operation. The present work is to improve the mechanical characterization of AA5052 by adding 1 and 2 wt % of Aluminium Titanate (Al2TiO5) reinforcement particles through a stir casting process. The influences of Al2TiO5 reinforcement particle’s microstructural analysis were investigated. The tensile, impact and hardness of the AA5052/ Al2TiO5 composites were also determined by Universal Testing Machine (UTM), Charpy, and Vickers microhardness tester, respectively. The AA5052/ 2%- Al2TiO5 composite microstructure shows a uniform grain distribution. The increased wt 2 % of reinforced particles to AA5052 resulted in an improved microhardness (73.4 HV) and tensile strength (210.28 Mpa).

Duplex stainless steel (DSS) 2205 grade is welded with austenitic filler wires (ERNiCrMo-3 and ERNiCrMo-4) using gas tungsten arc welding (GTAW) process to operate at marine environments. Microstructure using optical (OM) and scanning electron microscopes (SEM) with energy dispersive spectroscope (EDS) are utilized to examine the metallurgical characterization of DSS 2205 weldments. Microhardness, impact, and tensile tests are employed to obtain the mechanical properties of weldments. Secondary precipitates such as Mo23C6 and Cr23C6 are formed in the ERNiCrMo-3 weldment which reduced the mechanical properties. In this study, ERNiCrMo-4 filler wire is provided enhanced mechanical properties for welding DSS 2205.

The current work investigates the hot corrosion demeanour of Hastelloy X weldment produced with autogenous mode through key-hole plasma arc welding (K-PAW). The hot corrosion test has been performed for weldment in molten salt-1 (MS-1) (75 % Na2SO4 + 25 % V2O5) and molten salt-2 (MS-2) (75 % Na2SO4 + 20 % V2O5 + 5 % NaCl) circumstance for 25 hrs (25 cycles) at 900 °C. The MS-1 substrate of both base metal and weldment provided the lowest weight gain than the MS-2 substrate. The NaCl in the MS-2 causes severe hot corrosion on the substrate, whereas the absence of NaCl in MS-1 reduces the hot corrosion effects. The highest parabolic constant is observed for K-PAW weldment in MS-2 condition. The tendency of hot corrosion rate follows the order of, Base Metal MS-1 < K-PAW MS-1 < Base Metal MS-2 < K-PAW MS-2. The occurrence of protective phases like chromium oxides (Cr2O3), spinel oxides (NiCr2O4 and NiFe2O4) Nickel oxide (NiO) on the substrate resist the further oxidation.

The present paper examined the machining of Nimonic 75 experimentally with hexagonal boron nitride-based cutting fluid. Three different types of hexagonal boron nitride (hBN) nanofluids with various hBN concentrations and cutting variables (cutting speed and feed rate) are applied in turning experiments. Tool wear, cutting forces, roughness, residual stress, and chip morphology in machining Nimonic 75 alloy with the hBN nanofluids are analyzed. The effects caused by the variation of hBN concentration and cutting variables are discussed. The results show that cutting speed decrease the force, surface roughness, specific energy consumption, and chip reduction coefficient except for shear angle, friction coefficient, and residual stress. The increase in feed rate increases the machining characteristics and chip-tool interface indices parameters except for flank wear and specific energy consumption.

This research is an attempt to investigate the possibility of enhancing wear and corrosion behaviour of aluminium alloy and composites for high-temperature applications. The 319 alloys with minor additions of Ni, Ti and Fe elements using the liquid metallurgy technique, Al-Si-Cu-Mg matrix alloy (Al alloy) was obtained and it was used as a base alloy and it is reinforced with Silicon carbide (SiC), Magnesium oxide (MgO) under the following composites, namely Al alloy/3wt % MgO (AA-SRM), Al alloy/ 3wt % SiC (AA-SRS) and Al alloy/3wt %SiC-3wt % MgO (AAHRSM) using a stir casting route. The wear test was investigated under the following factors, namely constant sliding velocity 3.21 m/s, sliding distance up to 10000 m under different loadings (4.9, 9.8, 14.7, 19.62, and 24.5 N) using wear test by a pin on the disc test rig. The wear rate was calculated using the tested samples under different loadings, sliding distance, and weight concentration conditions.

The research aims to optimize the surface roughness, material removal rate (MRR), tool wear, and spark gap for input machining parameters such as Pulse on-off time and wire feed rate. The experiment results of WEDM of Duplex stainless steel are optimized by ANOVA and Response surface methodology (RSM) approach. Taguchi’s orthogonal array L9 (3*3) was used to design the test condition for the experiment. After the model validation, ANOVA was used to identify the most significant input factor on the output. Response surface methodology was used to find the ideal cutting conditions which produce the best-desired output in terms of less tool wear, lower surface roughness, lower spark gap, and higher material removal rate. The optimal MRR, Spark Gap, surface roughness, and tool wear parameters for Duplex Stainless Steel are obtained at Pulse on 110.23, Pulse off time of 56.0, and a wire feed rate of 1.0.

The objective of the study is to investigate the effect of current pulsation frequency on the weld bead microstructure, segregation and hardness of Hastelloy C-2000 weldments. Bead on Plate (BoP) welds were made by using Pulsed Current Gas Tungsten Arc Welding method (PCGTAW) at eleven different frequencies. The weld bead width and depth of penetration was measured with the help of Dinolite macro analyzer. The microstructure of weldments are further examined through optical microscope and Scanning Electron Microscopy (SEM) to identify the type of grain, grain coarsening and extent of the Heat Affected Zone (HAZ). The grain structure turn into finer and equiaxed in all cases and there was an optimum frequency range over which the significant grain refinement was observed. Microsegregation of alloying elements were computed with the aid of Energy Dispersive X-ray Spectroscopy (EDS). Vickers Hardness Tester was used to measure the hardness of the weld samples at ambient conditions.

Aluminium metal matrix composite are broadly used in various field like aerospace, marine and automobile application. The application of composites necessitates joining process and its difficult due to different materials. To address the considering difficulties the present study is, Cr2O3 was reinforced in Al 6061 matrix in 2 % to 6 % in the incremental step of 2 %. The stir casting method was used to fabricate the composites with 300 rpm stirring speed and the stirring time duration was 3 min throughout the fabrication process. The H13 tool is used for prepared friction stir welded (FSW) joints and tool having 6.7 mm pin diameter and 6 mm pin height. The fabrication process is conducted by 500 rpm and 700 rpm tool rotational speed with 50 mm/min and 60 mm/min welding speed receptively. The atmospheric environmental condition was preferred to perform friction stir welding.

The current research work scrutinized the influence of plasma arc in the metallurgical and mechanical behavior of Nimonic 80A weldment. Defect free weld bead of 6 mm thickness was achieved in a single pass through plasma arc welding. The microstructure of weldment is decorated with cellular dendritic structure at the center and at the weld interface region columnar dendritic structure was observed. Metallurgical analysis showed the Cr and Ti secondary precipitates in the interdendritic region of the WZ. The existence of M23C6 and Cr2Ti were observed through the X-ray diffraction analysis. Both tensile test and microhardness test were conducted to study the mechanical properties of weldment. The result concluded that both the strength and ductility inferior than base metal and the hardness of the weld bead is similar to that of BMl.

In these work AZ91 magnesium matrix composites reinforced with two weight fractions (5 and 10 wt. %) of TiB2 particulates were fabricated by cold chamber die casting process technique. The microstructure, density, hardness, mechanical properties of the specimens was investigated. Microstructure studies showed that fairly uniform distribution of reinforcements was achieved up to the weight fraction studied. As compared to base alloy AZ91, the hardness and tensile strength considerably increased with increasing reinforcement content. The presence of TiB2 particles improved the hardness around 24.4 %, compressive strength around 67.2% and the yield strength around 20%. The enormous amount of increment in the compressive strength due to the dislocation density created by the difference in thermal properties of matrix and composites and also due to the micro-pores presence in the composite.