Search Results

The present work compares the tribological properties of ZnO (Zinc Oxide) nanoparticle based lubricant with ZDDP (zinc dialkyl dithiophosphate) based lubricant. The nanolubricant was prepared by mixing the nanoparticles in base oil followed by ultrasonification and ZDDP based lubricant was prepared by mixing ZDDP and stirring with base oil. Base oil used was mineral base oil. Both the lubricants were tested at three different temperatures, loads and roughness values. The test was carried out on AISI 52100 steel samples prepared by wire cutting and were grinded to three different levels of surface roughness. Friction and wear tests were performed using a reciprocating sliding tribo-tester at three different loads and temperatures. Taguchi orthogonal array was used to reduce the number of experiments. SEM, EDS and AFM analysis were carried out to study the surface wear phenomenon.

In the fabrication of parts in auto and aero segments, the use of ceramic (SiCp, Al2O3p) reinforces aluminum alloy found to be increased than that of steel and cast iron. This matrix-reinforced alloy has a high strength to weight ratio along with higher modulus and hardness, the lower thermal coefficient of expansion, and improved tribological properties. To this extent, this paper investigates the turning characteristics and optimization study of newly developed metal matrix composites by the addition of both hard ceramic SiCp and soft stable lubricant molybdenum disulfide (MoS2p). The samples such as Sample 1: AlSi10Mg/3SiCp, Sample 2: AlSi10Mg/2MoS2p and Sample 3: AlSi10Mg/3SiCp /2MoS2p are prepared using the automated stir-casting machine. The particles are observed to be uniformly distributed in the composite. After density and hardness measurement, the samples are subjected to machining, and the responses are optimized by using response surface method.

Considerable weight of an automobile is constituted by the engine and there is scope for improvement in fuel efficiency and emission control through optimization of weight in the engine. In this work, AlSi10Mg alloy produced by the direct metal laser sintering (DMLS) is suggested for engine application which is a lightweight aluminum alloy. Mechanical properties like tensile strength, compressive strength, and hardness of both cast and DMLS manufactured alloy are compared followed by analysis of SEM images of tensile test fractured surfaces. Reciprocating wear test is carried out for one lakh cycles at 125°C temperature with SAE 40 grade oil as lubricant. Co-efficient of friction (COF), wear rate of the cast and DMLS manufactured samples are compared. Wear patterns are analyzed using SEM images of the wear tracks.

Epoxy carbon fiber composite materials are known for their light weight and high performance. They can be effective substitutes for commonly used materials for making drive shafts. Fiber orientation angle plays a major role in determining such a drive shaft’s responses. The responses considered in this paper are critical buckling torque, fundamental natural frequency and total deformation. A drive shaft made of epoxy carbon unidirectional prepreg is generated using ANSYS 18.0 ACP Composite Prepost. The objective of this paper is to determine an optimal configuration of fiber orientation angles for four, five and six-layered epoxy carbon drive shaft which tends to increase critical buckling torque and fundamental natural frequency while decreasing the total deformation. The optimal configuration which satisfies this objective for the three responses is identified by Minitab 17 statistical software.

In lieu of the drastic growth of the vehicle population, there is a huge consumption of fossil fuels and mineral oils for mobility. This leads to depletion in fossil fuels and mineral oils which are the by-products of petroleum. These fossil fuels can’t sustain for a long period of time because of its toxicity. In order to reduce the usage of existing mineral oil for lubrication, a source of non-edible oil from Jatropha curcus is processed as jatropha methyl ester (JME). It is holding high viscosity, density and easy blend with base oil. In this current work, the wear resistance of the lubricating oil is enhanced by the addition of nano-copper oxide particle blend with the base oil. The emission performance and tribological behavior have been experimentally tested in 98.2CC two-stroke air cooled engine. The 20% of JME blend with CuO nano particle provides better emission performance and wear characteristics than the other combination of blends.

Nickel based materials of Nimonic C-263 and Waspaloy are used nowadays for aerospace applications owing to its superior strength properties that are maintained at a higher temperature. Tool wear and cutting temperature in the vicinity of cutting edge are two essential machinability characteristics for any cutting tool. In this regard, this study is pursued to examine the influence of factors on measuring of tool wear (Vba) and cutting temperature (Ts) during dry machining of two alloys studied experimentally based on Taguchi method and response surface methodology. Taguchi’s L16 orthogonal array is used to design the experiment and a PVD (TiAlN), CVD (TiN/Al2O3/TiCN) coated carbide inserts are used on turning of two alloys. The factor effect on output responses are studied using analysis of variance, empirical models, and responses surface 3D plots. To minimize the response and to convert into one single optimum level, responses surface desirability function approach is applied.

The increased use of electronic systems has become a severe concern for electromagnetic pollution, leading to the development of materials to reduce electromagnetic interference (EMI). The present study investigated the EMI-shielding effectiveness (EMI-SE) of flax fiber polymer composite (FFC) in the available free space method by varying the wt.% of Rice husk ash (RHA) and hematite. The flax fiber was coated with the dip coating technique, and the coated fibers were used for preparing FFC by hand layup. The EMI-SE was measured at 32-33.5 dB in the X-band frequency range (8-12 GHz). As the cost is low and can be mass-produced, results show that the developed FFC are suitable for electric vehicle applications specifically to shield Electronic control units (ECU), where the interference effect needs to be reduced.

Natural fibers are one of the major ways to improve environmental pollution. In this study experimental investigation and simulation of honeycomb filled with cotton fabric, wood dust and polyurethane were carried out. This study determines the potential use of cotton fabric, wood dust as good sound absorbers. Automotive industries are looking forward to materials that have good acoustic properties, lightweight, strong and economical. This study provides a better understanding of sound-absorbing material with other mechanical properties. With simulation and experimental results, validation of works provides a wider industrial application for the interior of automotive industries including marine, aviation, railway industry and many more.