Search Results

The increasing importance of reducing greenhouse gas emissions and the ongoing evolution of vehicle-to-vehicle connectivity technologies have generated significant interest in platooning for commercial vehicles, where two or more vehicles travel in same traffic lane in relatively close proximity. This paper examines the effect of platooning on four increasingly aerodynamic tractor-trailer configurations, using a Lattice Boltzmann based CFD solver. Each platoon consisted of three identical tractor-trailer configurations traveling in the same lane at 65mph. Two different vehicle to vehicle gaps were studied, 5m and 9m, in addition to singleton (solitary) vehicles, representing an effectively infinite gap. Aerodynamic drag for the lead, middle, and trailing vehicle in the platooning configurations were compared to the corresponding single vehicle tractor-trailer configuration.

The importance of fuel economy and emission standards has increased rapidly with high fuel costs and new environmental regulations. This requires analysis techniques capable of designing the next generation long-haul truck to improve both fuel efficiency and cooling. In particular, it is important to have a predictive design tool to assess how exterior design changes impact aerodynamic performance. This study evaluates the use of a Lattice Boltzmann based numerical simulation and the National Research Council (NRC) Canada's wind tunnel to assess aerodynamic drag on a production Volvo VNL tractor-trailer combination. Comparisons are made between the wind tunnel and simulation to understand the influence of wind tunnel conditions on truck aerodynamic performance. The production VNL testing includes a full range of yaw angles to demonstrate the influence of cross wind on aerodynamic drag.

On-road emission measurements of 23 VN-trucks on a randomly chosen driving cycle, consisting of 10 miles two-lane and 8 miles four-lane road, showed tailpipe NOx emissions on fleet average of 0.96 g/bhp-hr, or 1.06 g/bhp-hr when including the time the exhaust gas temperature was below 200°C. Complementary measurements in a SET-cycle (13 point OICA -cycle) on a chassis dynamometer showed a tailpipe emission of 0.008 g PM per bhp-hr. Moreover, cost analysis show that the diesel fuel consumption remains unchanged whether the truck running on ULSD is equipped with a Combined Exhaust gas AfterTreatment System (CEATS) installed or not.

This study experimentally investigates the impact of Miller cycle strategies on the combustion process, emissions, and thermal efficiency in heavy-duty diesel engines. The experiments were conducted at constant engine speed, load, and engine-out NOx (1160 rev/min, 1.76 MPa net IMEP, 4.5 g/kWh) on a single cylinder research engine equipped with a fully-flexible hydraulic valve train system. Early Intake Valve Closing (EIVC) and Late Intake Valve Closing (LIVC) timing strategies were compared to a conventional intake valve profile. While the decrease in effective compression ratio associated with the use of Miller valve profiles was symmetric around bottom dead center, the decrease in volumetric efficiency (VE) was not. EIVC profiles were more effective at reducing VE than LIVC profiles. Despite this difference, EIVC and LIVC profiles with comparable VE decrease resulted in similar changes in combustion and emissions characteristics.

The commercial vehicle development process needs to consider the vehicle aerodynamics not only in ideal flow conditions, but also in the turbulent real world environment. The turbulent real world environment includes not only atmospheric turbulence, but also the vehicle to vehicle interactions that happen when driving around other vehicles or into and out of the wake of in/on coming vehicles. A vehicle driving into the wake of an oncoming vehicle not only experiences an increase in the total aerodynamic forces, it also experiences unsteady transient loads over the vehicle components such as windshield, mirror, sunvisor, door and side fairing. To properly design specific components, designers need to understand the magnitude of unsteady forces on various vehicle components, otherwise these components may fail which imposes warranty and safety risks. In this paper, we attempt to understand the various forces acting on the primary vehicle during a passing maneuver.

A large percentage of on-highway tractors today have air suspensions. Air suspensions require some type of control system to adjust the ride height. This system is usually referred to as a Load Leveling System. These systems come in a variety of different configurations but all basically have the same functions. When designed correctly, the system can reduce driveline vibration, reduce air consumption (improving compressor life and fuel efficiency), provide an accurate 5th wheel height and improve the ride quality. This paper explores how the characteristics of the leveling system affect the roll stability. One and Two-valve systems are considered, as well as, the position of the valve, response times, valve deadband and the systems response to an off-center load. Notably not every conceivable condition has been considered.