Search Results

This SAE Aerospace Information Report (AIR) describes field-level procedures to determine if 400 Hz electrical connections for external power may have been subjected to excessive wear, which may result in inadequate disengagement forces.

This SAE Aerospace Information Report (AIR) describes field-level procedures to determine if 400 Hz electrical connections for external power may have been subjected to excessive wear, which may result in inadequate disengagement forces.

This Aerospace Recommended Practice includes the following areas: basis for system requirements; selection of materials coupled with hazards and safety; configuration of design; system operation; and evalua tion testing.

This document covers the general requirements for hydraulic jacks as used on commercial aircraft. It can be applied to tripod, unipod, and axle jacks which may be used on open ramp areas as well as in the aircraft hanger.

This Aerospace Recommended Practice includes the following areas: basis for system requirements; selection of materials coupled with hazards and safety; configuration of design; system operation; and evaluation testing.

The primary purpose of a Propellant Transfer Unit (PTU) is to temperature-condition and weigh a specific amount of propellant, and transfer if to a vehicle propellant tank. A secondary purpose of a PTU may be to drain propellant from the vehicle tank and return it to the transfer unit when required. The transfer unit may also be used for flushing the vehicle fill lines and transfer unit with appropriate flushing fluids, followed with nitrogen for the purpose of drying the lines and weigh tank. The transfer unit may include provisions for helium purging of the propellant transfer tank and lines, ad supplying a blanket of helium pressure to the transfer tank. Each PTU consists of a piping system with appropriate propellant and pneumatic valves, regulators, relief valves, filters and a propellant pump. Various components such as a scrubber, bubbler, propellant cooler (heat exchanger), propellant weigh tank, weigh scale and a chiller may make up the balance of the assembly.

This document covers the general requirements for hydraulic aircraft jacks. It can be applied to tripod, unipod, and axle jacks that may be used on open ramp areas as well as in the aircraft hanger. Throughout this Aerospace Standard, the minimum essential criteria are identified by the key word “shall”. Recommended criteria are identified by use of the key word “should”. Deviation from recommended criteria should only occur after careful consideration and thorough service evaluation have shown alternate methods to provide an equivalent level of safety. The term “vertical load” throughout this Aerospace Standard is defined as the force imposed on the aircraft jack at the airframe jack point.

This specification covers the design and performance requirements for one type of sound aural protector.

This specification covers the design and performance requirements for one type of sound aural protector.

The main purpose of this test was to determine the application advantages of cushion tow hitches in comparison to the commonly used rigid tow hitch type fitted on heavy aircraft towing tractors. As diverse opinions emerged about its suitability since the introduction on the market of this new tow hitch type, it was intended to physically measure and evaluate the damping capability of this cushioned tow link when applied in practice.

The main purpose of this test was to determine the application advantages of cushion tow hitches in comparison to the commonly used rigid tow hitch type fitted on heavy aircraft towing tractors. As diverse opinions emerged about its suitability since the introduction on the market of this new tow hitch type, it was intended to physically measure and evaluate the damping capability of this cushioned tow link when applied in practice.

This SAE Aerospace Recommended Practice (ARP) is broken into various categories for convenience and ease of identification. It is the purpose of this document to provide certain criteria for the design and selection of stairways, for the boarding of passengers onto an aircraft. The criteria presented are limited to those factors which affect the safety of the passengers and are coordinated, where applicable, with the practices of the architectural profession, with respect to the design of stairways. The recommended practices are applicable to both mobile variable-elevation type stairways and to fixed-elevation stairways of the type built into an aircraft fuselage.

This ARP covers all types of ground support equipment required to support civil transport aircraft.

This SAE Aerospace Recommended Practice (ARP) covers all types of ground support equipment required to support civil transport aircraft.

This document provides information on the preparation and use of video for operational and maintenance training of personnel associated with GSE.

This document provides information on the preparation and use of video for operational and maintenance training of qualified personnel associated with GSE.

The following are suggested policies, procedures, and practices required to maintain mobile and fixed ground support equipment at airport passenger and cargo terminals. The principal purpose for ground support equipment maintenance is to provide the owner/user with safe, serviceable equipment, in good appearance, at minimal cost, and with minimum downtime. Maintenance programs initiated on ground support equipment must also conform to regulations controlling airport operations. This document has been divided into three sections corresponding to the three stages of equipment life; acquisition, maintenance, and disposal.

This specification covers the requirements for solid-state frequency converters with 480 [or 380] V 3-phase, 60 [or 50] Hz input and 115/200 V, 3-phase, 400 Hz output capable of powering aircraft type loads requiring MIL-STD-704D quality power. The frequency converter shall be a self-contained unit suitable for the environment of intended use. Typical applications include dedicated use at passenger loading bridges (mounted under the bridge in telescoping bridge applications or fixed installation at base of stationary type loading bridges) with weatherproof enclosures or hangar/lab use where indoor fixed or portable units can be used.