Search Results

The following is a list of the most common terminology used in describing automatic transmission functions.

The following is a list of the most common terminology used in describing automatic transmission functions.

The following is a list of the most common terminology used in describing automatic transmission functions.

The following is a list of the most common terminology used in describing automatic transmission functions.

The following is a list of the most common terminology used in describing automatic transmission functions.

The following is a list of the most common terminology used in describing automatic transmission functions.

This SAE Recommended Practice provides a method to determine the performance characteristics of the hydraulic oil pumps used in automatic transmissions and automatic transaxles. This document outlines the specific tests that describe the performance characteristics of these pumps over a range of operating conditions and the means to present the test data. This document is not intended to assess pump durability.

This SAE Recommended Practice provides a method to determine the performance characteristics of the hydraulic oil pumps used in automatic transmissions and automatic transaxles. This document outlines the specific tests that describe the performance characteristics of these pumps over a range of operating conditions and the means to present the test data. This document is not intended to assess pump durability.

This test procedure is intended to apply to hydraulic pump suction filters and strainers used in automotive automatic transmissions that include hydraulic power pumps. The various paragraphs of Section 5 include a variety of tests and alternative tests that are not applicable to all filters and applications, so the engineer must specify which tests are to be performed for a particular application. These test procedures are intended to evaluate filter functional performance characteristics only, durability is not evaluated under this standard. Filter design requirements must be specified by the engineer on the filter assembly drawing, an applicable engineering specification, or summarized on an application data sheet similar to that found in this recommended practice. See Figure 6. Pressure circuit filters, both barrier and system contamination control types, are not covered under this standard.

This test procedure is intended to apply to hydraulic pump suction filters and strainers used in automotive automatic transmissions that include hydraulic power pumps. The various paragraphs of Section 5, “Test Procedures,” include a variety of tests and alternative tests that are not applicable to all filters and applications, so the engineer must specify which tests are to be performed for a particular application. These test procedures are intended to evaluate filter functional performance characteristics only, durability is not evaluated under this standard. Filter design requirements must be specified by the engineer on the filter assembly drawing, an applicable engineering specification, or they may be summarized on an application data sheet similar to that found in this recommended practice. See Figure 6, “Filter Assembly Application and Data Sheet.” Pressure circuit filters, both barrier and system contamination control types, are not covered under this standard.

The purpose of this SAE Recommended Practice is to establish specifications for use as a guide to the automatic transmission and hydraulic systems designer, helping him to select cast iron sealing ring width, thickness, coatings, and other accepted design details.

This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face. This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face or the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded. This document applies to any internal combustion engine which can utilize SAE No. 6 through SAE No. 00 size flywheel housing for mounting a transmission.

This SAE standard defines flywheel housings and mating flange configuration for industry standardization, interchangeability, and compatibility. Dimensions and tolerances shown are millimeter (inch). Table 1 and the figure give dimensions for flywheel housings. The figure also shows spacing for eight, twelve, and sixteen bolt flange mounting patterns.

This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face. This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face or the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded. This document applies to any internal combustion engine which can utilize SAE No. 6 through SAE No. 00 size flywheel housing for mounting a transmission.

This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face. This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face or the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded. This document applies to any internal combustion engine which can utilize SAE No. 6 through SAE No. 00 size flywheel housing for mounting a transmission.

This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face. This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face or the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded. This document applies to any internal combustion engine which can utilize SAE No. 6 through SAE No. 00 size flywheel housing for mounting a transmission.

This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for engine flywheel mounted torque converters. Table 1 and Fig. 1 give dimensions for flywheel mounted-type torque converters. For torque converters using drive ring overcenter type disconnect clutch, see SAE J620.

This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for engine flywheel mounted torque converters. Table 1 and figure give dimensions for flywheels for torque converters. For torque converter with a front disconnect clutch, refer to applicable SAE Standard or Recommended Practice.

This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for engine flywheel mounted torque converters. Tables 1A and 1B and Figure 1 give dimensions for flywheels mounted-type torque converters. For torque converters using drive ring overcenter type disconnect clutch, see SAE J620.

This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for engine flywheel mounted torque converters. Tables 1A and 1B and Figure 1 give dimensions for flywheels mounted-type torque converters. For torque converters using drive ring overcenter type disconnect clutch, see SAE J620.