Search Results

A one-dimensional, two layer computational model was developed to predict the behavior of a clean and particulate-loaded catalyzed wall-flow diesel particulate filter (CPF). The model included the mechanisms of particle deposition inside the CPF porous wall and on the CPF wall surface, the exhaust flow field and temperature field inside the CPF, as well as the particulate catalytic oxidation mechanisms accounting for the catalyst-assisted particulate oxidation by the catalytic coating in addition to the conventional particulate thermal oxidation. The paper also develops the methodology for calibrating and validating the model with experimental data. Steady state loading experiments were performed to calibrate and validate the model.

Automotive exhaust emissions of polynuclear aromatic (C16+) hydrocarbons (PNA) were reduced by 65-70% by current emissions control systems and by about 99% by two experimental advanced emission control systems. At a given level of emission control, PNA emission was primarily controlled by fuel PNA content through the transient storage of PNA in engine deposits and their later emission under more severe engine operating conditions. A relatively minor contribution to PNA emission was made by PNA synthesized from lower molecular weight fuel aromatics, particularly C10-C14 aromatics. Deposit-related PNA emissions were linearly correlated with the PNA content of the deposit formation fuel. In comparison with a fuel of field-average PNA content (0.5 ppm benzo(a)pyrene), a field-maximum fuel (3 ppm) contained 4 to 7 times as much of three major PNA species and caused 3 to 5 times higher emissions of these species.

The development of the DDC methanol engine has been an evolutionary process, with each subsequent configuration showing significant durability and/or emission improvement over its predecessor. Sixty demonstration engines are now in service in the field, including fifty-four (54) urban bus engines, five (5) truck engines, and one (1) generator set engine. While nitrogen oxide (NOx) and particulate emissions from the methanol engine are inherently low, a durable solution to the effective control of hydrocarbon (HC) emissions has been an especially challenging area. The 1991 Federal urban bus transient emission standards (including 0.10 gm/bhp-hr particulate) have been met with several combinations of compression ratio, intake port height, exhaust valve cam profile, injector tip design, and electronic control strategies, and without exhaust aftertreatment devices or fuel ignition improvers.

A wide range of emissions were characterized from a heavy-duty diesel engine operated on conventional low sulfur (∼375 ppm) fuel, equipped with manually controlled EGR and a catalyzed particulate filter (CPF). The effect of the CPF and engine load was studied, along with a comparison of results between the gravimetric and thermal optical methods (TOM) for determining diesel particulate levels. Data were obtained from four of the EPA old 13 mode test cycle steady-state operating conditions, i.e., Modes 11, 10, 9, and 8 using a 1995 Cummins M11-330E engine with a Corning EX-80 cordierite particulate filter, coated with a platinum catalyst (5 g/ft3).

A study was conducted to assess the effects of a water-diesel fuel emulsion with and without an oxidation catalytic converter (OCC) on steady-state heavy-duty diesel engine emissions. Two OCCs with different metal loading levels were used in this study. A 1988 Cummins L10-300 heavy-duty diesel engine was operated at the rated speed of 1900 rpm and at 75% and 25% load conditions (EPA modes 9 and 11 respectively) of the 13 mode steady-state test as well as at idle. Raw exhaust emissions' measurements included total hydrocarbons (HC), oxides of nitrogen (NOx) and nitric oxide (NO). Diluted exhaust measurements included total particulate matter (TPM) and its primary constituents, the soluble organic (SOF), sulfate (SO42-) and the carbonaceous solids (SOL) fractions. Vapor phase organic compounds (XOC) were also analyzed. The SOF and XOC samples were analyzed for selected polynuclear aromatic hydrocarbons (PAHs).

Diesel particulate matter in both the diluted and undiluted state is subject to the processes of coagulation, condensation or evaporation, and nucleation which causes continuous changes in its physical characteristics. The Electrical Aerosol Analyzer (EAA) is used to measure the diesel particle size distribution in the MTU dilution tunnel for a naturally aspirated direct-injection diesel engine operated on the EPA 13 mode cycle. The design and development of accurate and repeatable sampling methods using the EAA are presented. These methods involve both steady-state tunnel and bag measurements. The data indicate a bimodal nature within the 0.001 to 1 μm range. The first mode termed the “embroynic mode” has a saddle point between 0.005 to 0.015 μm and the second mode termed the “aggregation mode” lies between .08 to .15 μm for the number distribution.

The diesel engine emits exhaust particles that pose a unique set of measurement requirements. To document the state-of-the-art of measurement technology and to improve measurement quality, the Smoke and Particulate Panel of the Diesel Exhaust Composition group of the Coordinating Research Council reviewed published literature and particulate-sampling data generated by panel members to identify (1) the effects of key sampling parameters on measured particulate mass, (2) the causes of measurement variability, (3) the effects of dilution system design on particulate mass measurement, and (4) promising real-time mass measurement methods. The panel found greater measurement difficulty associated with particulates than for gaseous pollutants because of engine-produced variations, the sensitivity of measured particulate mass to dilution parameters, and random errors in the independent measurements which comprise a particulate measurement.

One of the more objectionable aspects of the use of diesel engines has been the emission of particulate matter. A literature review of combustion flames, theoretical calculations and dilution tunnel experiments have been performed to elucidate the chemical and physical processes involved in the formation of diesel particulate matter. A comparative dilution tunnel study of diluted and undiluted total particulate data provided evidence supporting calculations that indicate hydro-carbon condensation should occur in the tunnel at low exhaust temperatures. The sample collection system for the measurement of total particulate matter and soluble sulfate in particulate matter on the EPA 13 mode cycle is presented. A method to correct for hydrocarbon interferences in the EPA barium chloranilate method for the determination of sulfate in particulate matter is discussed.

Exhaust emission of polynuclear aromatic hydrocarbons (PNA) and of phenols has been studied with a variety of test fuels, using cyclic tests in five vehicles-including one without emission control (NC), two with engine modification (EM) control, and two with experimental very low emission systems. The experimental systems both reduced phenol emission to less than 0.5% and PNA emission to about 1% of the levels observed in the NC vehicle. Phenols were reduced 30% by one EM vehicle, but not by the other; while PNA emissions were reduced by 70% in both EM vehicles. Fuel composition influenced emissions both directly and through engine deposits. Direct effects included increased phenol emission from increased fuel aromatics and, generally, increased PNA emission from increased fuel aromatics, from increased fuel PNA, and from the presence of a high-boiling naphtha.

A computer simulation model to predict the thermal responses of an on-highway heavy duty diesel truck in transient operation was used to study several important cooling system design and operating variables. The truck used in this study was an International Harvester COF-9670 cab-over-chassis vehicle equipped with a McCord radiator, Cummins NTC-350 diesel engine, Kysor fan-clutch and shutter system, aftercooler, and standard cab heater and cooling system components. Input data from several portions of a Columbus to Bloomington, Indiana route were used from the Vehicle Mission Simulation (VMS) program to determine engine and vehicle operating conditions for the computer simulation model. The thermostat-fan, thermostat-shutter-fan, and thermostat-winterfront-fan systems were studied.