Search Results

Measurement of emissions from small utility engines has usually been accomplished using steady-state raw emissions procedures such as SAE Recommended Practice J1088. While raw exhaust measurements have the advantage of producing modal exhaust gas concentration data for design feedback; they are laborious, may influence both engine performance and the emissions themselves, and have no provision for concurrent particulate measurements. It is time to consider a full-dilution procedure similar in principle to automotive and heavy-duty on-highway emission measurement practice, leading to improvements in many of the areas noted above, and generally to much higher confidence in data obtained. When certification and audit of small engine emissions become a reality, a brief dilute exhaust procedure generating only the necessary data will be a tremendous advantage to both manufacturers and regulatory agencies.

Methods for measurement and expression of crankcase or “blowby” emissions from diesels were developed and demonstrated on a test engine. These methods were subsequently used to characterize gas and particulate emissions from two in-service engines. Crankcase emissions were evaluated under engine operating conditions corresponding to the EPA 13-mode certification test. Substances for which analyses were conducted included regulated pollutants, sulfate, trace elements, nitrosamines, individual hydrocarbons, and aldehydes. Emissions from the diesel crankcases were compared to exhaust emissions (where possible) to assess their importance. Analysis for nitrosamines was continued beyond the original effort, utilizing another test engine.

This paper describes the characterization of regulated and unregulated exhaust emissions, particularly aldehydes, from ten 1978 and 1979 high mileage catalyst-equipped gasoline fueled automobiles which have been driven for approximately 50,000 miles. The ten automobiles were evaluated as-received and after a tune-up to manufacturer’s specifications, over the Light-Duty Federal Test Procedure (FTP) and the Highway Fuel Economy Driving Schedule (HFET). Exhaust constituents measured, in addition to the regulated emissions, include: aldehydes, particulates, sulfides, amines, and several additional compounds.

This paper describes the effort to characterize regulated and unregulated exhaust emissions from four gasoline powered passenger cars equipped with three-way catalyst control systems. The vehicles have been evaluated over four test cycles, with three fuels at four mileage accumulation points. In addition to the currently regulated automobile emissions, exhaust emission components measured include: sulfate, aldehydes, ammonia, sulfur dioxide, cyanide, and several other compounds. From the standpoint of toxicity, the most significant emissions from three-way catalyst systems are the currently regulated emissions, followed to a lesser degree by the sulfate emissions.

Two of the types of particulate trap systems that have evolved to control exhaust particulate matter include the catalyzed trap system and the additive-regenerated trap system. Exhaust emissions from these two types of trap systems have been characterized and quantified as completely as possible. The two vehicles evaluated in the study included a 1986 Mercedes-Benz 300 SDL, which utilizes a catalyzed trap system, and a prototype Volkswagen, which utilizes an additive trap system. The vehicles were tested using a chassis dynamometer, a dilution tunnel, and a constant volume sampler. The exhaust emissions were evaluated as to driving cycle, presence of particulate trap, engine condition, trap condition, and fuel aromatic content.

Gaseous and particulate emissions from two heavy-duty diesel engines were characterized while the engines were operated on five different fuels. Characterization included mass rates of major exhaust products, plus analysis of particulate matter for sulfate, trace elements, major elements, total solubles, and other properties. Analysis of rate and composition data was conducted with regard to fuel and engine effects on particulate. Two large particulate samples were also collected for later analysis on groups of organics present.

Emissions from a Stirling engine-powered 1986 model light-duty truck were measured using current EPA (chassis dynamometer) emissions certification procedures and certain specialized tests. Three fuels were used including unleaded gasoline, a blend of MTBE in unleaded gasoline, and JP-4. City (FTP) cycles and Highway (FET) cycles were run on all three fuels, and emissions measured during the cycles included hydrocarbons (HC), carbon monoxide (CO), and oxides of nitrogen (NOx). Fuel economy was also calculated for these tests. Additional pollutants measured during some of the tests included aldehydes, 1,3-butadiene, individual hydrocarbon species, and total particulate matter. In addition to the cyclic schedules, steady-state conditions were run on JP-4 and straight gasoline for regulated emissions and fuel economy. The conditions consisted of several simulated gradients at three vehicle speeds, plus idle.

Particulate and gaseous emissions from two light-duty diesel vehicles were measured over eight operating schedules, using five different fuels. Characterization included regulated exhaust emissions and a number of unregulated constituents. Non-routine gas measurements included phenols, hydrocarbon boiling range, and aldehydes. Particulate characterization included mass rates and concentrations, visible smoke, aerodynamic sizing, total organics, BaP, sulfate, phenols, trace elements, and major elements. Statistical analysis of emissions data was undertaken using fuel properties and operating schedule statistics as independent variables. Regressions were computed for a few variables, and analysis of variance and multiple comparisons were used where the data were not suitable for regression analysis.

This paper describes the findings of a laboratory effort to demonstrate improved automotive exhaust emission control with a cold-start hydrocarbon collection system. The emission control strategy developed in this study incorporated a zeolite molecular sieve in the exhaust system to collect cold-start hydrocarbons for subsequent release to an active catalytic converter. A prototype emission control system was designed and tested on a gasoline-fueled vehicle. Continuous raw exhaust emission measurements upstream and downstream of the zeolite molecular sieve revealed collection, storage, and release of cold-start hydrocarbons. Federal Test Procedure (FTP) emission results show a 35 percent reduction in hydrocarbons emitted during the cold-transient segment (Bag 1) due to adsorption by the zeolite.

This study compared diesel exhaust emission from four different diesel fuels: a conventional low sulfur D2 diesel (0.03% sulfur, 28% aromatics), California Air Resources Board (CARB) diesel (0.015% sulfur, 8% aromatics), “Swedish” diesel (<0.001% sulfur, 4% aromatics), and a Fischer-Tropsch (F-T) diesel (<0.0001% sulfur, <0.1% aromatics) fuel. The comparison included regulated emissions, hydrocarbon speciation, air toxics, aldehydes and ketones, particle size distribution, and greenhouse gas emissions. Testing was conducted using a Cummins B-Series engine installed both in a heavy light-duty truck operating on a chassis dynamometer and on an engine dynamometer. The chassis driving cycles included city, highway, and aggressive driving operation. Engine dynamometer tests included the U.S. transient cycle.

This study compared four different candidate fuels which were prepared by blending different components with a typical No. 2 diesel. Two fuels were blended with a synthetic diesel prepared from natural gas condensate, and all candidate fuels were splash blended with a proprietary additive package from International Fuel Technology Inc. (IFT). These fuels were then compared to the No. 2 diesel and to a California Air Resources Board (CARB) equivalent diesel fuel. The comparisons included fuel properties such as sulfur content, aromatics, cetane, lubricity, distillation; emissions; and fuel consumption. Emission testing was conducted on a 1991 Detroit Diesel Series 60. The Environmental Protection Agency (EPA) transient cycle was utilized for emissions, fuel characterization was performed according to ASTM standards, and fuel consumption was calculated by the carbon balance method.

Two additive blends proposed for improving the flame luminosity in neat methanol fuel were investigated to determine the effect of these additives on the exhaust emissions in a dual-fueled Volkswagen Jetta. The two blends contained 4 percent toluene plus 2 percent indan in methanol and 5 percent cyclopentene plus 5 percent indan in methanol. Each blend was tested for regulated and unregulated emissions as well as a speciation of the exhaust hydrocarbons resulting from use of each fuel. The vehicle exhaust emissions from these two fuel blends were compared to the Coordinating Research Council Auto-Oil national average gasoline (RF-A), M100, and M85 blended from RF-A. Carter Maximum Incremental Reactivity Factors were applied to the speciated hydrocarbon emission results to determine the potential ozone formation for each fuel. Toxic emissions as defined in the 1990 Clean Air Act were also compared for each fuel.

In the United States, most school buses are powered by diesel engines. Some have advocated replacing diesel school buses with natural gas school buses, but little research has been conducted to understand the emissions from school bus engines. This work provides a detailed characterization of exhaust emissions from school buses using a diesel engine meeting 1998 emission standards, a low emitting diesel engine with an advanced engine calibration and a catalyzed particulate filter, and a natural gas engine without catalyst. All three bus configurations were tested over the same cycle, test weight, and road load settings. Twenty-one of the 41 “toxic air contaminants” (TACs) listed by the California Air Resources Board (CARB) as being present in diesel exhaust were not found in the exhaust of any of the three bus configurations, even though special sampling provisions were utilized to detect low levels of TACs.

Newly designed Teflon® O-rings along with XAD-2 resin, stainless steel screens, lock rings, and glass cartridges were used to construct a new semi-volatile organic compounds (SVOC's) sampling device. This new sampling device allows direct and repeated sampling, extraction, and cleaning without ever having to be disassembled or reassembled. This new XAD-2 glass cartridge (X2) was compared with three other sampling methods namely Empore® membrane (EM), hexane impinger (HI), and “Cold Trap” (CT) for SVOC sampling efficiency on diesel engine exhaust emissions. The X2 method showed the highest overall SVOC collection efficiency, followed by the EM and HI methods. The X2 method has higher trapping efficiency for the oxygenates, polycyclic aromatic hydrocarbons (PAH's), alkyl cyclohexanes, and the alkyl aromatics than the other three SVOC sampling methods. The HI method has the highest trapping efficiency for the normal alkanes.

Two methods of sampling exhaust emissions are typically used for characterizing emissions from diesel engines: total dilution which uses a constant volume sampling (CVS) system and partial flow dilution which relies on proportionally diluting a small part from the main exhaust stream. The CVS dilutes the entire exhaust flow to a constant volumetric flowrate which allows for proportional sampling of the exhaust species during transient engine operation. For partial dilution sampling during transient engine operation, obtaining a proportional sample is more rigorous and dilution of the extracted sample must be continuously changed throughout the cycle in order for the extracted sample flowrate to be proportional to the continuously changing exhaust flow. Typically, regulated emissions measured using both methods for an engine platform have shown good correlation. The focus for this work was on the experimental investigation of the two methods for the measurement of unregulated species.

Exhaust emission data from several fuel effects studies were normalized and subjected to statistical analyses. The goal of this work was to determine whether emission effects of property variation in alternate-source fuels were similar, less pronounced, or more pronounced than the effects of property variation in petroleum fuels. A literature search was conducted, reviewing hundreds of studies and finally selecting nine which dealt with fuel property effects on emissions. From these studies, 15 test cases were reported. Due to the wide variety of vehicles, fuels, test cycles, and measurement techniques used in the studies, a method to relate them all in terms of general trends was developed. Statistics and methods used included bivariate correlation coefficients, regression analysis, scattergrams and goodness-of-fit determinations.

This paper discusses a method developed to counter the variability of media interferences for the measurement of aldehydes and ketones in automotive exhaust. Dinitrophenylhydrazine (DNPH) Derivatization Methodology for the collection of aldehyde and ketone compounds in vehicle exhaust has been in use for over thirty years. These carbonyl compounds are captured by passing diluted exhaust gas through a sample medium containing DNPH. The sampling medium can take the form of DNPH dispersed on a solid sorbent or as a DNPH solution in a solvent such as acetonitrile. Carbonyl compounds react readily to form DNPH derivatives which are stable and which absorb ultra-violet (UV) light, facilitating quantitative measurement. However, when the procedure was developed, emissions rates from vehicles were much higher than the current (2010) emissions levels.

A two-phase study was performed to establish a standard diesel exhaust composition which could be used in the future development of light-duty diesel exhaust aftertreatment. In the first phase, a literature review created a database of diesel engine-out emissions. The database consisted chiefly of data from heavy-duty diesel engines; therefore, the need for an emission testing program for light- and medium-duty engines was identified. A second phase was conducted to provide additional light-duty vehicle emissions data from current technology vehicles. Engine-out diesel exhaust from four 2004 model light-duty vehicles with a variety of engine displacements was collected and analyzed. Each vehicle was evaluated using five steady-state engine operating conditions and two transient test cycles (the Federal Test Procedure and the US06). Regulated emissions were measured along with speciation of both volatile and semi-volatile components of the hydrocarbons.

This paper summarizes the impact of recent developments in diesel fuel and the effect of these changes in conjunction with emerging compression-ignition engine technologies. Some changes were made to reduce exhaust emissions or were the result of advancements in aftertreatment systems. These changes included fuel properties such as aromatic and sulfur content, cetane number, density, lubricity, and viscosity. Other changes included the introduction of blending components and additives. Blending components included such things as water, ethanol, and bio-mass materials. The pros and cons related to these changes in diesel fuel technologies are discussed.

This paper describes experiments to determine the effect on exhaust emissions of starting on compressed natural gas (CNG) and then switching to gasoline once the catalyst reaches operating temperature. Carbon monoxide, oxides of nitrogen, and detailed exhaust hydrocarbon speciation data were obtained for dedicated CNG, then unleaded gasoline, and finally CNG start -gasoline run using the Federal Test Procedure at 24°C and at -7°C. The result was a reduction in emissions from the gasoline baseline, especially at -7°C. It was estimated that CNG start - gasoline run resulted in a 71 percent reduction in potential ozone formation per mile.