Search Results

Because of the more hostile environment in the compression ignition engine compared to the spark ignition engine, development and application of CI engine in-cylinder diagnostic methods have lagged those for SI engines. However, with more stringent federally mandated particulate and NOx standards which will go into effect in 1991 and 1994, the need for detailed information on the combustion processes in the cylinder is vital to controlling tailpipe emissions. The present paper contains a summary of the state-of-the-art techniques for determining in-situ species concentrations and profiles; particle concentrations, profiles, and size distributions; and temperature fields. Optical and physical probing methods, total cylinder dumping methods, and optical diagnostics applied for use in CI engine combustion chambers are discussed.

Several sources of variation in quantitative analytical ferrography are investigated. A standard ferrography analysis procedure is developed. Normalization of ferrographic data to account for the amount of oil used to make the ferrograms is discussed. Procedures to minimize the errors involved with calculating three quantitative ferrography parameters: the area covered by the large particles, AL (%/ml of oil), the area covered by the small particles, AS (%/ml of oil) and Area Under the Curve, AUC, (%-mm/ml of oil) are outlined. Ferrographic data are presented which show that the volume and dilution ratio of the oil sample being analyzed have a major effect on the accuracy of the analysis. Several variables which influence the area covered readings of the particle deposit on a ferrogram are discussed. The accuracy of quantitative analytical ferrography is assessed.

Active regeneration experiments were performed on a Cummins 2007 aftertreatment system by hydrocarbon dosing with injection of diesel fuel downstream of the turbocharger. The main objective was to characterize the thermal oxidation rate as a function of temperature and particulate matter (PM) loading of the catalyzed particulate filter (CPF). Partial regeneration tests were carried out to ensure measureable masses are retained in the CPF in order to model the oxidation kinetics. The CPF was subsequently re-loaded to determine the effects of partial regeneration during post-loading. A methodology for gathering particulate data for analysis and determination of thermal oxidation in a CPF system operating in the engine exhaust was developed. Durations of the active regeneration experiments were estimated using previous active regeneration work by Singh et al. 2006 [1] and were adjusted as the experiments progressed using a lumped oxidation model [2, 3].

Combustion characteristics of an L-head engine combustion chamber have been examined using ionization probes and piezioelectric pressure transducers. The method describes how pressure rise rates, peak pressures, mean effective pressures, and flame arrival times were recorded. The flame arrival times were then used to find the position and shape of the flame front as a function of time. The influence of spark plug location on the above parameters was then examined for two different combustion chamber shapes.

Protocols for sampling and analysis of particulate and gaseous-phase diesel emissions were developed to characterize the chemical and biological effects of using ceramic traps as particulate control devices. A stainless-steel sampler was designed, constructed, and tested with XAD-2 sorbent for the collection of volatile organic compounds (VOC). Raw exhaust levels of TPM and SOF and mutagenicity of the SOF and VOC were all reduced when the traps were used. Hydrocarbon mass balances indicated that some hydrocarbons were not collected by the sampling system and that the proportions of collected SOF and VOC were altered by the use of the traps. SOF hydrocarbons appeared to be derived mainly from engine lubricating oil; VOC hydrocarbons were apparently fuel-derived. There was no apparent effect on SOF mutagenicity due to either sampling time or reexposure of particulate to exhaust gases.

A microprocessor controlled lubricating oil cooling system of truck diesel engine was designed to minimize the sump oil temperature fluctuation during start-up and nonsteady engine operations. Model reference adaptive control method is utilized in the control system design. The analysis involved in the design of the microprocessor controlled oil cooling system, and the applications of a special vehicle-engine-cooling system (VEC) computer simulation code in the implementation and testing of the model reference adaptive control strategy are described. Using the VEC simulation code, the performance of the microprocessor controlled oil cooling system and the conventionally controlled oil cooling systems were compared for the ATB, temperature disturbances, and cold weather transient tests. An explanation of each test, as well as a review of the results of comparison tests are presented.

The development of the DDC methanol engine has been an evolutionary process, with each subsequent configuration showing significant durability and/or emission improvement over its predecessor. Sixty demonstration engines are now in service in the field, including fifty-four (54) urban bus engines, five (5) truck engines, and one (1) generator set engine. While nitrogen oxide (NOx) and particulate emissions from the methanol engine are inherently low, a durable solution to the effective control of hydrocarbon (HC) emissions has been an especially challenging area. The 1991 Federal urban bus transient emission standards (including 0.10 gm/bhp-hr particulate) have been met with several combinations of compression ratio, intake port height, exhaust valve cam profile, injector tip design, and electronic control strategies, and without exhaust aftertreatment devices or fuel ignition improvers.

A computer simulation program was developed to simulate the thermal responses of an on-highway, heavy duty diesel powered truck in transient operation for evaluation of cooling system performance. Mathematical models of the engine, heat exchangers, lubricating oil system, thermal control sensors (thermostat and shutterstat), auxiliary components, and the cab were formulated and calibrated to laboratory experimental data. The component models were assembled into the vehicle engine cooling system model and used to predict air-to-boil temperatures. The model has the capability to predict real time coolant, oil and cab temperatures using vehicle simulation input data over various routes.

Flame arrival data, determined by ionization gaps and a radiation detector, are presented for a multi-hole CFR engine equipped with six spark plugs spaced around the periphery of the combustion chamber, using a shrouded intake valve to produce swirl and with a standard valve to eliminate it. For results with the shrouded valve, path equations for the burnt gases are derived for several velocity distributions that satisfy the Navier-Stokes equations of motion for the unburned gas. Previous velocity distribution and observed flame movement data are presented in support of the derived model for the path of the burnt gases.

Low emission heavy-duty diesel engines are increasingly utilizing four-valve designs with vertical central injectors. However, two-valve DI diesel engines with inclined injectors offset from the centerline of the piston bowl are likely to continue to be used in medium and light duty applications for some time. In such situations, designing of the hole-type nozzle is very difficult and may cause unavoidable back-drilling problems. The purpose of this paper is to solve back-drilling problems connected with hole-type nozzles and improve fuel-air mixing which leads to more efficient combustion. Based on geometric considerations, this paper introduces single-cone hole-type nozzles, double-cone hole-type nozzles, and the critical principal angles for hole-type nozzles. The single-cone hole-type nozzles and double-cone hole-type nozzles can meet requirements for height of the spray impingement points and spray orifice distribution angle at the same time.

Measurements of particle concentrations in one cylinder of a 1982 5.7 liter GM V-8 diesel engine have been made using a unique total cylinder sampling system. The first part of the paper is devoted to an examination of the performance of the sampling system. The role of blowoff and nucleation in the formation of sample artifacts is discussed. The remainder of the paper is devoted to the results of a study of the formation and removal of carbon particles during diesel engine combustion. Several operating conditions have been examined. The influence of injection timing, load, EGR, and oxygen addition on particle formation and removal has been investigated. The concentrations of volatile and nonvolatile particulate matter have been measured as a function of crankangle position. Particle formation begins 1-5 crankangle degrees (CAD) after the start of combustion.

The formation of particles in the combustion chamber of a direct injection diesel engine has been studied with the use of the Total Cylinder Sampling Method. With this method, nearly the entire contents of the cylinder of an operating diesel engine can be quickly removed at various times during the combustion process. The particle mass and size distributions present in the sample can then be analyzed. If quenching of the combustion process is quick and complete, the resulting samples are representative of the particle mass and size distributions present in the cylinder near the time sampling begins. This paper discusses the effect of injection timing and piston bowl shape on the particle formation and oxidation. Example size distribution measurements are also shown. The particle concentrations in the cylinder were measured for three different injection timings with the standard piston installed in the engine.

A unique system which allows sampling of the entire contents of one of the cylinders of a 5.7-liter V-8 indirect-injection diesel engine has been developed. An explosively actuated cutter ruptures a diaphragm in the combustion chamber and allows the contents of the cylinder to rush out and be subsequently diluted and quenched with cool nitrogen. Particles are collected with a high-volume impactor/filter system. This system has been used to collect a series of particle samples at crankangles ranging from 5 to 40 degrees after top dead center. Particle samples from the exhaust were also obtained. The samples have been extracted to determine the soluble organic fraction. These extracts have been analyzed for five polycyclic aromatic compounds: pyrene, fluoranthene, benz(a)pyrene, benz(k)fluoranthene, and 1-nitropyrene. The results indicate significant removal of the first four between the combustion chamber and the exhaust manifold.

A miniature homogenous charge compression ignition (HCCI) free-piston engine compressor aimed at an ankle-foot orthosis application is described. Analysis of the human ankle shows that a fluid power source in the neighborhood of 10 W is needed. To account for compressor and actuator inefficiencies, the power output at the engine cylinder is designed to be 30 W. A compact engine compressor package has been designed and mathematically modeled. Experiments using existing engine components characterized the leakage model. Through the dynamic simulation of the engine, major parameters of the engine have been specified. Simulations indicate that the HCCI free-piston engine compressor, designed in a prototype package scale of about 80×40×20 mm is a viable compact and efficient fluid power supply. Simulation results demonstrate that the overall efficiency of the engine compressor is expected to be 5.9% and that the package should have a higher energy density than batteries.

The formation of NO2 in the cylinder of a diesel engine has been investigated using a total cylinder sampling technique and a simple kinetic model. Exhaust measurements of NO2 as a function of equivalence ratio and as function of time after engine start were made. Samples obtained by total cylinder sampling from an operating direct injection diesel engine showed NO2/NO ratios of 25 to 50%. This is much higher than the 1 to 3% which was measured in the exhaust. Simulations of the sampling process indicate that conversion of NO to NO2 is at least partially responsible for the high NO2/NO measurements. However, the processes which produce the NO to NO2 conversion during the sampling also occur during normal combustion. This may lead to high NO2 concentrations during the combustion cycle which are then lowered during the expansion to the measured exhaust concentrations.

Carbon black particles, which morphologically and chemically simulate a diesel exhaust soot, were mixed with the intake air of a single-cylinder direct injection diesel engine to investigate the efficiency of their removal by oxidation in the combustion chamber. An aerosol generation system, which is capable of generating carbon black aerosol of a size distribution and mass flow rate comparable to those of the soot agglomerates, was developed first. The aerosol was then introduced into the engine which was operating on conventional fuel. Four methods were used to characterize the exhaust particles: an electrical aerosol analyzer, a condensation nuclei counter, a low volume filter, and a micro-orifice cascade impactor. The size distribution and concentration of the diesel soot particles in the lubricants were investigated by methods of photosedimentation and quantitative spectrophotometry, respectively.

Time resolved primary and agglomerate particle size distribution measurements have been made on samples obtained from within the cylinder and from the exhaust of a single-cylinder modification of a 2.8 liter displacement, four-cylinder, naturally-aspirated, high swirl, direct-injection diesel engine. The total cylinder sampling method has been used to sample, quench, and dilute the entire contents of the cylinder in about 1 ms. Experiments have been performed at an equivalence ratio of 0.7 and a speed of 1000 RPM. An electrostatic aerosol sampler and a transmission electron microscope have been used to determine primary and agglomerate particle size distributions for both in-cylinder and exhaust samples. An electrical aerosol analyzer and a diffusion battery followed by a condensation nucleus counter were used to further characterize the agglomerate size distributions of exhaust samples.

There is a growing body of evidence that in-cylinder surfaces play an important role in determining the nature and quantity of soot emitted by diesel engines. This paper describes recent experimental results which demonstrate the importance of both the deposition of soot on walls during the combustion process and its subsequent reentrainment during exhaust blowdown. Soot deposition was demonstrated both experimentally and theoretically. The principal mechanism of soot deposition during combustion is thermophoresis. Our results suggest that the gross rate of in-cylinder deposition in the indirect injection diesel engine is between 20 and 45 percent of the net soot emission rate. Thus, a significant fraction of the soot emitted may have been stored on combustion chamber surfaces and protected from oxidation. Further evidence of wall deposition and subsequent reentrainment has been obtained by making time-resolved measurements of soot concentrations in the exhaust.

A test reactor was designed for a 6.7 kW, 303 cc, single cylinder, air cooled, gasoline fueled engine. The reactor was very efficient at hydrocarbon (HC) and carbon monoxide (CO) reductions - with up to 99.9 and 98.6% removed, respectively. It had no effect on oxides of nitrogen (NOx) emissions. With the reactor, the engine met the California Air Resources Board (ARB) proposed Tier II emission standards. A factorial test was used to determine that A/F ratio and air injection rate significantly affected CO reduction efficiency whereas air injection location, ignition timing, and engine load did not. Relationships were established between CO reduction, air injection rate, and reactor core temperature.

Soot is the largest component of contaminants found in the diesel engine lubricating oil. The soot enters lubricating oil mainly through thermophoretic deposition on the cylinder wall. Although the mechanism is still not fully understood, it is generally accepted that soot particles promote engine wear, reducing engine component service life, fuel efficiency and performance. This problem will be further exacerbated when more and more diesel engines use EGR to reduce NOx emissions and when lubricating oil consumption is drastically reduced to control particulate emissions. In this study, lubricating oil samples were taken from 7 different operating diesel engines. The size distribution and concentration of the diesel soot particles in the lubricants were investigated by methods of photosedimentation and quantitative spectrophotometry. The size distributions were compared to those of soot particles in the exhaust.