Search Results

Precise prediction of combustion parameters such as peak firing pressure (PFP) or crank angle of 50% burned mass fraction (MFB50) is essential for optimal engine control. These quantities are commonly determined from in-cylinder pressure sensor signals and are crucial to reach high efficiencies and low emissions. Highly accurate in-cylinder pressure sensors are only applied to test rig engines due to their high cost, limited durability and special installation conditions. Therefore, alternative approaches which employ virtual sensing based on signals from non-intrusive sensors retrieved from common knock sensors are of great interest. This paper presents a comprehensive comparison of selected approaches from literature, as well as adjusted or further developed methods to determine engine combustion parameters based on knock sensor signals. All methods are evaluated on three different engines and two different sensor positions.

A realistic simulation of the wall heat transfer is an imperative condition for the accurate analysis and simulation of the working process of IC engines. Due to its simplicity in application, zero-dimensional wall heat transfer models dominate engine cycle simulation in practice. However, experience shows that existing zero-dimensional models for wall heat transfer do not yield satisfactory results in certain applications. This is mainly due to a lack of consideration of the actual flow field in the cylinder. In this paper a quasi-dimensional heat transfer model, which is based on a detailed description of the turbulent flow field in the combustion chamber, is described. The model presents a consistent approach for the high pressure as well as the low pressure part of the cycle. The results of the heat transfer model are compared with results from the correlation by Woschni/Huber and with experimental results from various DI Diesel engines.

A realistic modeling of the wall heat transfer is essential for an accurate analysis and simulation of the working cycle of internal combustion engines. Empirical heat transfer formulations still dominate the application in engine process simulations because of their simplicity. However, experiments have shown that existing correlations do not provide satisfactory results for all the possible operation modes of hydrogen internal combustion engines. This paper describes the application of a flow field-based heat transfer model according to Schubert et al. [1]. The models strength is a more realistic description of the required characteristic velocity; considering the influence of the injection on the global turbulence and on the in-cylinder flow field results in a better prediction of the wall heat transfer during the compression stroke and for operations with multiple injections. Further an empirical hypothesis on the turbulence generation during combustion is presented.

Virtual sensing refers to the processing of desired physical data based on measured values. Virtual sensors can be applied not only to obtain physical quantities which cannot be measured or can only be measured at an unreasonable expense but also to reduce the number of physical sensors and thus lower costs. In the field of spark ignited internal combustion engines, the virtual sensing approach may be used to predict the cylinder pressure signal (or characteristic pressure values) based on the acceleration signal of a knock sensor. This paper presents a method for obtaining the cylinder pressure signal in the high-pressure phase of an internal combustion engine based on the measured acceleration signal of a knock sensor. The approach employs a partial differential equation to represent the physical transfer function between the measured signal and the desired pressure. A procedure to fit the modeling constants is described using the example of a large gas engine.

Optimization of engine warm-up behavior has traditionally made use of experimental investigations. However, thermal engine models are a more cost-effective alternative and allow evaluation of the fuel saving potential of thermal management measures in different driving cycles. To simulate the thermal behavior of engines in general and engine warm-up in particular, knowledge of heat distribution throughout all engine components is essential. To this end, gas-side heat transfer inside the combustion chamber and in the exhaust port must be modeled as accurately as possible. Up to now, map-based models have been used to simulate heat transfer and fuel consumption; these two values are calculated as a function of engine speed and load. To extend the scope of these models, it is increasingly desirable to calculate gas-side heat transfer and fuel consumption as a function of engine operating parameters in order to evaluate different ECU databases.

Hydrogen is frequently cited as a future energy carrier. Hydrogen allows a further optimization of internal combustion engines, especially with direct injection. In order to assess various concepts, detailed thermodynamic analyses were carried out. Effects, which can be neglected with conventional fuels (e.g. losses due to injection during compression stroke) are considered. These basics as well as several results from test bed investigations are described within this article. Wall heat losses were found to have a major influence on overall efficiency and are thus investigated in detail, based on local surface temperature measurement. Finally, concepts that allow an increase in engine efficiency and lowest NOx emissions are demonstrated.

This paper summarizes the results of several investigations on in-cylinder heat transfer during high-pressure and gas exchange phases as well as heat transfer in the inlet and outlet ports for a number of different engine types (DI Diesel, SI and gaseous fueled engine). The paper contains a comparision of simulation results and experimental data derived from heat flux measurements. Numerical results were obtained from zero-, one- and three-dimensional simulation methods. Time and spatially resolved heat fluxes were measured applying the surface temperature method and special heat flux sensors. The paper also includes an assessment of different sensor types with respect to accuracy and applicability.

The 3D CFD method has become an essential and reliable tool for the development of modern large gaseous-fuelled engines. This holds especially true for the optimization of mixture formation and charge motion in prechamber engines to ensure suitable conditions near the spark plug at ignition time. In order to initialize a quick combustion process, an ignitable mixture with high turbulence but moderate velocity must prevail round the spark plug. However, suitable models for combustion and heat transfer are inevitable for a realistic simulation of the whole engine cycle. Within 3D CFD codes the combustion process is usually calculated using the PDF (probability density function) - model; heat transfer is modeled based on the logarithmic wall function. Experimental investigations were carried out on a single cylinder research engine in order to validate the combustion model used and different heat transfer models.