Refine Your Search

Date

Date

Topic

Topic

Bodies and Structures Defense industry Steel Titanium Design Engineering and Styling Headlamps Motor Vehicle Council

Search Results

Viewing 1 to 20 of 50
123Next >Last >>
Sort by title
Standard

Considerations for Suspension Modification
1999-06-01
HISTORICAL
J2492_199906
The scope of this document is limited specifically to the following types of passenger vehicles: automobiles, light trucks, and sport/utility vehicles. This document addresses modifications as they apply to legal use of the vehicle, and examines suspension modification as it applies to stock (as manufactured) ride height, and changed (raised or lowered) ride height. Note that modifications of ride height are considered, exclusive of wheel and/or tire modifications, which can also have potentially serious side effects, and are outside the scope of this document.
Standard

FILM ANALYSIS GUIDES FOR DYNAMIC STUDIES OF TEST SUBJECT
1969-12-01
HISTORICAL
J138_196912
This SAE Recommended Practice is intended to provide guidelines for the identification of subjects used in dynamic tests. It establishes recommendations for location and description of target areas on test subjects or test devices, as well as recommendations for photographic calibration and timing.
Standard

Film Analysis Guides for Dynamic Studies of Test Subjects
2019-10-02
CURRENT
J138_201910
This SAE Recommended Practice is intended to provide guidelines for the identification of subjects used in dynamic tests. It establishes recommendations for location and description of target areas on test subjects or test devices, as well as recommendations for photographic calibration and timing.
Standard

MOTOR VEHICLE SEATING SYSTEMS
1968-07-01
HISTORICAL
J879B_196807
This SAE Recommended Practice establishes uniform test procedures and certain minimum performance requirements for motor vehicle seats and seat adjusters. It is limited to tests that can be conducted on uniform test fixtures and equipment available in commercial laboratory test facilities. This practice includes a minimum requirement for horizontal forward loads encountered in vehicle forward impacts, and horizontal loads obtained by impacting the vehicle from the rear. The requirements and test procedures in this recommended practice reflect current technology and industry experience. It is intended to subject this recommended practice to a continuing review and revision as technology advances and experience is expanded.
Standard

Motor Vehicle Seat Belt Anchorages - Design Recommendations
2014-10-28
HISTORICAL
J383_201410
This SAE Recommended Practice specifies design recommendations for the location of seat belt assembly anchorages which will promote proper transfer of occupant restraint forces on the strongest parts of the human anatomy to the vehicle or seat structure. Test procedures are specified in SAE J384.
Standard

Motor Vehicle Seating Systems
2019-10-02
CURRENT
J879B_201910
This SAE Recommended Practice establishes uniform test procedures and certain minimum performance requirements for motor vehicle seats and seat adjusters. It is limited to tests that can be conducted on uniform test fixtures and equipment available in commercial laboratory test facilities. This practice includes a minimum requirement for horizontal forward loads encountered in vehicle forward impacts, and horizontal loads obtained by impacting the vehicle from the rear. The requirements and test procedures in this recommended practice reflect current technology and industry experience. It is intended to subject this recommended practice to a continuing review and revision as technology advances and experience is expanded.
Standard

NUMBERING SYSTEM FOR REAMERS
1990-11-01
HISTORICAL
J2124_199011
This SAE Recommended Practice provides a systematic method for the identification of various types of hand, machine, and shell reamers used in industrial applications. When used as recommended in this report, the numbering system will assist in obtaining consistent reamer descriptions in communications. The report was developed in cooperation with the Automotive Industry Action Group (AIAG).
Standard

NUMBERING SYSTEM FOR STANDARD DRILLS
1990-11-01
HISTORICAL
J2122_199011
This SAE recommended practice provides a systematic method for the identification of standard drills. It is intended to assist in the cataloging and supplying of these tools. The report was developed in cooperation with the Automotive Industry Action Group (AIAG).
Standard

Numbering System for Multiple Diameter Cutting Tools
2019-10-09
CURRENT
J2276_201910
This SAE Recommended Practice provides a systematic method for the identification of multiple diameter cutting tools. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Numbering System for Multiple Diameter Cutting Tools
1998-10-13
HISTORICAL
J2276_199810
This SAE Recommended Practice provides a systematic method for the identification of multiple diameter cutting tools. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Numbering System for Single Diameter and Taper Reamers
2019-10-09
CURRENT
J2124_201910
This SAE Recommended Practice provides a systematic method for the identification of single diameter and taper reamers. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying reamers that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Numbering System for Single Diameter and Taper Reamers
1998-10-14
HISTORICAL
J2124_199810
This SAE Recommended Practice provides a systematic method for the identification of single diameter and taper reamers. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designators to prevent specifying reamers that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Numbering System for Taps
1998-10-14
HISTORICAL
J2123_199810
This SAE Recommended Practice provides a systematic method for the identification of ground thread taps for inch sizes up to 9.999 in with a Maximum Thread-per-Inch of 99.9, and Metric sizes up to 99.9 mm with a Maximum pitch of 9.99 mm. It is intended to assist in the cataloging and supplying of these tools. It is not intended for ACME, Buttress, or similar type thread forms. NOTE 1— Caution must be taken when assigning codes to prevent specifying taps that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Numbering System for Taps
2019-10-09
CURRENT
J2123_201910
This SAE Recommended Practice provides a systematic method for the identification of ground thread taps for inch sizes up to 9.999 in with a Maximum Thread-per-Inch of 99.9, and Metric sizes up to 99.9 mm with a Maximum pitch of 9.99 mm. It is intended to assist in the cataloging and supplying of these tools. It is not intended for ACME, Buttress, or similar type thread forms. NOTE 1— Caution must be taken when assigning codes to prevent specifying taps that cannot be physically or economically manufactured. NOTE 2— The Code Number coming from the manufacturer MUST reflect the actual tool construction. NOTE 3— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Numbering Systems for End Mills
2019-10-09
CURRENT
J2342_201910
This SAE Recommended Practice provides a systematic method for the identification of End Mills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designation to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

Numbering Systems for End Mills
1999-01-20
HISTORICAL
J2342_199901
This SAE Recommended Practice provides a systematic method for the identification of End Mills. It is intended to assist in the cataloging and supplying of these tools. NOTE 1— Caution must be taken when assigning codes for designation to prevent specifying cutting tools that cannot be physically or economically manufactured. NOTE 2— In particular without limitation, SAE disclaims all responsibility for the accuracy or completeness of information contained within this report if the standards of this report are retrieved, combined, or used in connection with any software.
Standard

PASSENGER CAR SIDE DOOR LATCH SYSTEMS
1965-05-01
HISTORICAL
J839B_196505
This SAE Recommended Practice establishes minimum performance requirements and test procedures for evaluating and testing passenger car side door latch systems. It is limited to tests that can be conducted on uniform test fixtures and equipment in commercially available laboratory test facilities. The test procedures and minimum performance requirements outlined in this recommended practice are based on currently available engineering data. It is intended that all portions of the recommended practice will be periodically reviewed and revised, as additional knowledge regarding vehicle latch performance under impact conditions is developed.
Standard

PASSENGER CAR SIDE DOOR LATCH SYSTEMS
1982-07-01
HISTORICAL
J839_198207
This SAE Recommended Practice establishes minimum performance requirements and test procedures for evaluating and testing passenger car side door latch systems. It is limited to tests that can be conducted on uniform test fixtures and equipment in commercially available laboratory test facilities. The test procedures and minimum performance requirements outlined in this recommended practice are based on currently available engineering data. It is intended that all portions of the recommended practice will be periodically reviewed and revised, as additional knowledge regarding vehicle latch performance under impact conditions is developed.
123Next >Last >>
X