Search Results

This paper introduces a diagnostic technique for the detection of misfiring cylinders in internal combustion engines. The technique requires the analysis of the instantaneous angular velocity of an engine flywheel. The results show that the mean cyclic acceleration, maximum variation in angular velocity, and the cyclic period of acceleration can be used as a measure for the mean net torque and the mean net expansion pressure torque produced by each cylinder. The proposed technique has proven to be effective in identifying a faulty cylinder using efficient and simple computations.

A detailed analysis has been made on the Cetane Scale presently used to rate the autoignition quality of fuels. The effect of the increase in temperature and pressure, as a result of increasing the compression ratio, on the ignition delay has been theoretically and experimentally analyzed. It has been found that the ignition delay is more sensitive to air temperature than air pressure. The sensitivity increases with the drop in the cetane number of the fuel. Many techniques have been examined to modify the present cetane scale. A modified scale has been developed by raising the inlet temperature from 150°F to 350°F without changing the rest of the rating technique. The modified scale is very effective in extending the scale to zero cetane number and is able to rate the low ignition quality fuels.

A new approach referred to as (P-ω) method, has been developed at Wayne State University to determine the instantaneous friction and its components in internal combustion engines. The method is based on the fact that the instantaneous cylinder gas forces and the instantaneous frictional, inertia and load forces cause the instantaneous variation in the flywheel angular velocity. The instantaneous total friction forces have been computed for a single diesel engine, under idling conditions. A breakdown of the friction into its components and a formulation for each component has been made. By applying linear regression, correlations between the individual components of the friction losses and the different parameters have been developed. The components are classified into two categories: piston assembly losses and crankcase assembly losses.

A new formulation is developed for the ignition delay (ID) in diesel engines to account for the effect of piston motion on the global autoignition reaction rates. A differentiation is made between the IDe measured in engines and IDv, measured in constant volume vessels. In addition, a method is presented to determine the coefficients of the IDe correlation from actual engine experimental data. The new formulation for IDe is applied to predict the misfiring cycles during the cold starting of diesel engines at different low ambient temperatures. The predictions are compared with experimental results obtained on a multi-cylinder heavy-duty diesel engine.

This paper identifies the original function of the Cetane Scale and examines some problem of concern to the technical community. The following six problems have been analyzed: i) inability of the ASTM D-613 method to rate low ignition quality fuels, ii) instability of the ignition delay meter, iii) inconformity of the CFR combustion system with actual diesel systems, iv) invalidity of Cetane number in correlating the I.D. for different fuels, engines and operating conditions, v) inaccuracy of Cetane number in ranking the overall performance and emission behaviour of fuels in diesel engines and vi) inability of Cetane number in rating the cold startability of diesel engines on different fuels. Possible solutions to the above problems have been examined.

Ion current sensors have been considered for the feedback electronic control of gasoline and diesel engines and for onboard vehicles powered by both engines, while operating on their conventional cycles or on the HCCI mode. The characteristics of the ion current signal depend on the progression of the combustion process and the properties of the combustion products in each engine. There are large differences in the properties of the combustible mixture, ignition process and combustion in both engines, when they operate on their conventional cycles. In SI engines, the charge is homogeneous with an equivalence ratio close to unity, ignition is initiated by an electric spark and combustion is through a flame propagating from the spark plug into the rest of the charge.

This paper describes the development and results of a mathematical model for a single cylinder, naturally-aspirated, direct-injection diesel engine, used to study the effect of compression ratio on the different performance parameters. The parameters investigated include; thermal and mechanical efficiency, ignition delay, mean effective pressure, maximum cylinder pressure, mechanical friction, and blowby. The model simulates a full thermodynamic cycle and considers the intake and exhaust processes, instantaneous heat transfer, instantaneous friction, and instantaneous blowby. Based on the model results, a prediction of an optimum CR for the engine is made.

The correlations between the physical properties and autoignition parameters of several alternate fuels have been examined. The fuels are DF-2 and its blends with petroleum derived fuels, coal derived fuels, shale derived fuels, high aromatic naphtha sun-flower oils, methanol and ethanol. A total of eighteen existing correlations are discussed. An emphasis is made on the suitability of each of the correlations for the development of electronic controls for diesel engines when run on alternate fuels. A new correlation has been developed between the cetane number of the fuels and its kinematic viscosity and specific gravity.

Cycle-to-cycle cylinder pressure variation has been observed in a CFR prechamber diesel engine when low ignition quality (low cetane number) fuels are burned. A statistical analysis of this phenomenon for various fuels and blends with cetane numbers as low as zero has been made. Operating conditions used were those specified by the ASTM Cetane Method for rating diesel fuels, in which the inlet air temperature is 150°F. Additional analysis was made at increased inlet air temperatures of 250°F and 350°F. The cycle-to-cycle variation has been characterized by the variation in the ignition (or pressure rise) delay time. It has been found to increase sharply as fuel cetane number is decreased below 20. The variation in dynamic injection timing was also measured and correlated with that for ignition delay.

The local variation of the crankshaft's speed in a multicylinder engine is determined by the resultant gas-pressure torque and the torsional deformation of the crankshaft. Under steady-state operation, the crankshaft's speed has a quasi-periodic variation and its harmonic components may be obtained by a Discrete Fourier Transform (DFT). Based on a lumped-mass model of the shafting, correlations are established between the harmonic components of the speed variation and the corresponding components of the engine torque. These correlations are used to calculate the gas-pressure torque or the indicated mean effective pressure (IMEP) from measurements of the crankshaft's speed.

An experimental and numerical study was carried out to simulate the diesel spray behavior during cold starting conditions inside two single-cylinder optically accessible engines. One is an AVL single-cylinder research diesel engine converted for optical access; the other is a TACOM/LABECO engine retrofitted with mirror-coupled endoscope access. The first engine is suitable for sophisticated optical diagnostics but is constrained to limited consecutive fuel injections or firings. The second one is located inside a micro-processor controlled cold room; therefore it can be operated under a wide range of practical engine conditions and is ideal for cycle-to-cycle variation study. The intake and blow-by flow rates are carefully measured in order to clearly define the operation condition. In addition to cylinder pressure measurement, the experiment used 16-mm high-speed movie photography to directly visualize the global structures of the sprays and ignition process.

Combustion instability is investigated during the cold starting of a single cylinder, direct injection, 4-stroke-cycle, air-cooled diesel engine. The experiments covered fuels of different properties at different ambient air temperatures and injection timings. The analysis showed that the pattern of misfiring (skipping) is not random but repeatable. The engine may skip once (8-stroke-cycle operation) or twice (12-stroke-cycle operation) or more times. The engine may shift from one mode of operation to another and finally run steadily on the 4-stroke cycle. All the fuels tested produced this type of operation at different degrees. The reasons for the combustion instability were analyzed and found to be related to speed, residual gas temperature and composition, accumulated fuel and ambient air temperature.

The variation of the crankshaft's speed is influenced by the action of the cylinders and shall reflect the contribution of each cylinder to the total engine output. At the same time, the speed variation is influenced by the torsional stiffness of the cranks, the mass moments of inertia of the reciprocating mechanisms and the average speed and load of the engine. As the result, the variation of angular motion of the crankshaft is complex, each particular influence changing its importance as speed and load are modified. The diagnostic method presented in the paper is based on the analysis of the amplitudes and phases of the lowest harmonic orders of the measured speed and is capable to determine the average Indicated Mean Effective Pressure (IMEP), to detect nonuniformities in cylinder operation and to identify the faulty cylinder(s).

A mathematical model Is developed to study the transient behavior of a four-stroke, single cylinder naturally-aspirated, DI diesel engine during cranking and starting. The model simulates the full thermodynamic cycle of the engine and includes detailed sub-models for the intake and exhaust gas flow processes, autoignition combustion, heat transfer, mechanical friction, blowby, and engine dynamics. The model considers the period of time from starter on until the engine reaches the idle speed. Experimental data and results obtained from the engine are used to calibrate and validate the model. A comparison of results from the model and the experiments generally show good agreement for the starting conditions investigated.

An experimental study was carried out to visualize the spray and combustion inside an AVL single-cylinder research diesel engine converted for optical access. The injection system was a hydraulically-amplified electronically-controlled unit injector capable of high injection pressure up to 180 MPa and injection rate shaping. The injection characteristics were carefully characterized with injection rate meter and with spray visualization in high-pressure chamber. The intake air was supplied by a compressor and heated with a 40kW electrical heater to simulate turbocharged intake condition. In addition to injection and cylinder pressure measurements, the experiment used 16-mm high-speed movie photography to directly visualize the global structures of the sprays and ignition process. The results showed that optically accessible engines provide very useful information for studying the diesel combustion conditions, which also provided a very critical test for diesel combustion models.

Several dynamic parameters for the diagnosis of reciprocating combustion engines are investigated. Emphasis is made on the effect of sampling. The dynamic parameters include the frequency analysis, autocorrelation function, the frequency analysis of the autocorrelation function, variation of the angular velocity peaks, variation of the angular velocity depressions, variation of the angular velocity from before to after top dead center, velocity index and acceleration index. Two sampling techniques are used to measure the instantaneous angular velocity of a six cylinder, four-stroke-cycle diesel engine, under healthy and faulty conditions. The most effective dynamic parameters for engine diagnostics are determined.

An experimental study was conducted to characterize the dynamics and spray behavior of a wide range of minisac and Valve-Covered-Orifice (VCO) nozzles using a high-pressure diesel common-rail system. The measurements show that the resultant injection-rate is strongly dependent on common-rail pressure, nozzle hole diameter, and nozzle type. For split injection the dwell between injections strongly affects the second injection in regards to the needle lift profile and the injected fuel amount. The minisac nozzle can be used to achieve shorter pilot injections at lower common-rail pressures than the VCO nozzle. Penetration photographs of spray development in a high pressure, optical spray chamber were obtained and analyzed for each test condition. Spray symmetry and spray structure were found to depend significantly on the nozzle type.

I The effect of Cetane Number (CN) of the fuel and the addition of cetane improvers on the cold starting and white smoke emissions of a diesel engine was investigated. Tests were conducted on a single-cylinder, four-stroke-cycle, air-cooled, direct-injection, stand-alone diesel engine in a cold room at ambient temperatures ranging from 25 °C to - 5 °C. Five fuels were used. The base fuel has a CN of 49.2. The CN of the base fuel was lowered to 38.7 and 30.8 by adding different amounts of aromatic hydrocarbons. Iso-octyl nitrate is added to the high aromatic fuels in order to increase their CN to 48.6 and 38.9 respectively. Comparisons are made between the five fuels to determine the effect of CN and the additive on cylinder peak pressure, heat release rate, cold start-ability, combustion instability, hydrocarbon emissions and solid and liquid particulates.

In view of the new regulations for diesel engine emissions, EGR is used to reduce the NOx emissions. Diluting the charge with EGR affects the autoignition, combustion as well as the regulated and unregulated emissions of diesel engines, under different operating conditions. This paper presents the results of an investigation on the effect of EGR on the global activation energy and order of the autoignition reactions, premixed and mixing-controlled combustion fractions, the regulated (unburned hydrocarbons, NOx, CO and particulates), aldehydes, CO2 and HC speciation. The experiments were conducted on two different direct injection, four-stroke-cycle, single-cylinder diesel engines over a wide range of operating conditions and EGR ratios.

The combustion and emission characteristics of a high speed, small-bore, direct injection, single cylinder, diesel engine are investigated using two different nozzles, a 430-VCO (0.171mm) and a 320 Mini sac (0.131mm). The experiments were conducted at conditions that represent a key point in the operation of a diesel engine in an electric hybrid vehicle (1500 rpm and light load condition). The experiments covered fuel injection pressures ranging from 400 to 1000 bar and EGR ratios ranging from 0 to 50%. The effects of nozzle hole geometry on the ignition delay (ID), apparent rate of energy release (ARER, ARHR), NOx, Bosch smoke unit (BSU), CO and hydrocarbons are investigated.