Search Results

Abstract The ASTM D130 was first issued in 1922 as a tentative standard for the detection of corrosive sulfur in gasoline. A clean copper strip was immersed in a sample of gasoline for three hours at 50°C with any corrosion or discoloration taken to indicate the presence of corrosive sulfur. Since that time, the method has undergone many revisions and has been applied to many petroleum products. Today, the ASTM D130 standard is the leading method used to determine the corrosiveness of various fuels, lubricants, and other hydrocarbon-based solutions to copper. The end-of-test strips are ranked using the ASTM Copper Strip Corrosion Standard Adjunct, a colored reproduction of copper strips characteristic of various degrees of sulfur-induced tarnish and corrosion, first introduced in 1954. This pragmatic approach to assessing potential corrosion concerns with copper hardware has served various industries well for a century.

Abstract In recent years, lean-burn gasoline Spark-Ignition (SI) engines have been a major subject of investigations. With this solution, in fact, it is possible to simultaneously reduce NOx raw emissions and fuel consumption due to decreased heat losses, higher thermodynamic efficiency, and enhanced knock resistance. However, the real applicability of this technique is strongly limited by the increase in cyclic variation and the occurrence of misfire, which are typical for the combustion of homogeneous lean air/fuel mixtures. The employment of a Pre-Chamber (PC), in which the combustion begins before proceeding in the main combustion chamber, has already shown the capability of significantly extending the lean-burn limit. In this work, the potential of an ultralean PC SI engine for a decisive improvement of the thermal efficiency is presented by means of numerical and experimental analyses.

Abstract Due to the increasing requirements for efficiency, the wide range of characteristics and the improved possibilities of modern development and production processes, compressors in turbochargers have become more individualized in order to adapt to the requirements of internal combustion engines. An understanding of the working mechanisms as well as an understanding of the way that losses occur in the flow allows a reduced development effort during the optimization process. This article presents three-dimensional (3D) Computational Fluid Dynamics (CFD) investigations of the loss mechanisms and quantitative calculations of individual losses. The 3D-CFD method used in this article will reduce the drawbacks of one-dimensional calculation as far as possible. For example, the twist of the blades is taken into account and the “discrete” method is used for loss calculation instead of the “average” method.

Abstract Regulations limiting GreenHouse Gases (GHG) from Heavy-Duty (HD) commercial vehicles in the United States (US) and European Union will phase in between the 2024 and 2030 model years. These mandates require efficiency improvements at both the engine and vehicle levels, with the most stringent reductions required in the heaviest vehicles used for long-haul applications. At the same time, a 90% reduction in oxides of nitrogen (NOx) will be required as part of new regulations from the California Air Resources Board. Any technologies applied to improve engine efficiency must therefore not come at the expense of increased NOx emissions. Research into advanced engine architectures and components has identified improved turbomachine efficiency as one of the largest potential contributors to engine efficiency improvement. However this comes at the cost of a reduced capability to drive high-pressure Exhaust Gas Recirculation (EGR).

Abstract In the United States (USA), transportation is the largest single source of greenhouse gas (GHG) emissions, representing 27% of total GHGs emitted in 2020. Eighty-three percent of these came from road transport, and 57% from light-duty vehicles (LDVs). Internal combustion engine (ICE) vehicles, which still form the bulk of the United States (US) fleet, struggle to meet climate change targets. Despite increasingly stringent regulatory mechanisms and technology improvements, only three US states have been able to reduce their transport emissions to the target of below 1990 levels. Fifteen states have made some headway to within 10% of their 1990 baseline. Largely, however, it appears that current strategies are not generating effective results. Current climate-change mitigation measures in road transport tend to be predominantly technological.

Abstract Composite ceramic brake discs are made of ceramic material reinforced with carbon fibers and offer exceptional advantages that translate directly into higher vehicle performance. In the case of an electric vehicle, it could increase the range of the vehicle, and in the case of conventional internal combustion engine vehicles, it means lower fuel consumption (and consequently lower CO2 emissions). These discs are typically characterized by complex internal geometries, further complicated by the presence of drilling holes on both friction surfaces. To estimate the aerothermal performance of these discs, and for the thermal management of the vehicle, a reliable model for predicting the air flowing across the disc channels is needed. In this study, a real carbon-ceramic brake disc with drilling holes was investigated in a dedicated test rig simulating the wheel corner flow conditions experimentally using the particle image velocimetry technique and numerically.

Abstract This article presents an investigation of energy transfer, flame propagation, and emissions formation mechanisms in a four-cylinder, downsized and boosted, spark ignition engine fuelled by either directly injected compressed natural gas (DI CNG) or gasoline (GDI). Three different charge preparation strategies are examined for both fuels: stoichiometric engine operation without external dilution, stoichiometric operation with external exhaust gas recirculation (EGR), and lean burn. In this work, experiments and engine modelling are first used to analyze the energy transfer throughout the engine system. This analysis shows that an early start of fuel injection (SOI) improves fuel efficiency through lower unburned fuel energy at low loads with stoichiometric DI CNG operation.

Abstract The equivalent consumption minimization strategy (ECMS) is an instantaneous optimization method implemented online for hybrid electric vehicles (HEVs) to improve fuel economy. To fulfill the near-optimal performance of ECMS, equivalent factors (EFs) must be well tuned for different powertrains and driving cycles. This study proposes a hierarchical offline optimization framework which tunes the penalty value of state of charge (SOC) balance in the outer layer and optimizes EFs based on heuristic algorithms in the inner layer. A comprehensive analysis is conducted to evaluate three heuristic algorithms, including the genetic algorithm (GA), the nonlinear-inertia-decreasing particle swarm optimization algorithm (NLPSO), and the novel firefly algorithm (FA). The traversal optimization method (TOM) is chosen as the benchmark. Besides, a sensitivity analysis is carried out to reveal the impact of the penalty value on the battery SOC balance.

Abstract Electric power steering (EPS) systems have become the most advantageous steering system used in vehicles. They provide better fuel efficiency and a more compact design over traditional hydraulic power steering (HPS) systems. However, EPS systems are afflicted with unwanted noise and vibration that can undermine the safety of drivers. This article presents a mathematical framework for vibration analysis in a column-type EPS system. The steering column is modeled as a continuous clamped column. The equations of motion are derived using Hamilton’s principle, and explicit expressions are presented for the frequency and transmissibility equations. A three-degrees-of-freedom (3-DOF) dynamic model is also presented by an approximation of the stiffness, damping, and mass of the steering column. The results of the proposed analytical models are validated using ANSYS simulation.

Abstract The article presents a concept of a new turbine engine in the field of pressure gain combustion (PGC). The engine operates according to the Humphrey thermodynamic cycle, where pressure increase was obtained in a combustion chamber closed with a valve. The intake mushroom valve and exhaust swing valve were designed for self-acting. They operate as a result of gas pressure and centrifugal force. The engine consists of two rotating combustion chambers and a counterrotating radial turbine, in both of which mechanical power was generated. The gas flow in the mobile valve system, combustion process, gas expansion, and torque generation were analyzed by means of Computational Fluid Dynamics (CFD) analysis. The investigated engine concept is characterized by significant energy efficiency.

Abstract This work presents a generalized methodology for the optimal thermal management of different powertrain devices. The methodology is based on the adoption of an electrically driven pump and on the development of a specifically designed controller algorithm. This is achieved following a Model Predictive Control approach and requires a generalized lumped-parameters model of the thermal exchange between the device walls and the coolant. The methodology is validated at a test rig, with reference to a four-cylinder spark-ignition engine. Results show that the proposed approach allows a reduction in fuel consumption of about 2-3% during the engine warm-up, a decrease in fuel consumption of about 1-2% during fully warmed operation, and an estimated fuel consumption reduction of about 2.5-3% in an NEDC. Finally, the investigation highlights that the proposed approach reduces the risk of after-boiling when the engine is rapidly switched off after a prolonged high-load operation.

Abstract A pre-chamber ignition system has the potential to reduce the burn duration of lean-burn gasoline engine combustion and can achieve a reduced knock occurrence from the distributed ignition sources. Pre-chamber ignition produces high-velocity turbulent jets, and these jets often reach sonic velocity and produce shock waves inside the combustion chamber. These shock waves make knock detection difficult with a conventional surface-mounted acoustic knock sensor. This article discusses how an acoustic knock sensor works with a pre-chamber ignition and evaluates different cylinder pressure-based knock detection strategies and proposes a method that eliminates the influence of jet-induced oscillations on knock detection.

Abstract Deep learning (DL)-based approaches enable unprecedented control paradigms for propulsion systems, utilizing recent advances in high-performance computing infrastructure connected to modern vehicles. These approaches can be employed to optimize diesel aftertreatment control systems targeting the reduction of emissions. The optimization of the Trapped Soot Load (TSL) reduction in the Diesel Particulate Filter (DPF) is such an example. As part of the diesel aftertreatment system, the DPF stores the soot particles resulting from the combustion process in the engine. Periodically, the stored soot is oxidized during a DPF regeneration event. The efficiency of such a regeneration influences the fuel economy, and potentially the service interval of the vehicle. The quality of a regeneration depends on the operating conditions of the DPF, the engine, and the ability to complete the regeneration event.

Abstract Demonstrating ring pack operation in an operating engine is very difficult, yet it is essential to optimize engine performance parameters such as blow-by, oil consumption, emissions, and wear. A significant amount of power is lost in friction between piston ring–cylinder liner interfaces if ring pack parameters are not optimized properly. Thus, along with these parameters, it is also necessary to reduce friction power loss in modern internal combustion engines as the oil film thickness formed between the piston ring and liner is vital for power loss reduction due to friction. Hence, it has also been a topic of research interest for decades. Piston and ring dynamics simulation software are used extensively for a better ring pack design. In this research work, a similar software for piston ring dynamics simulation reviews the ring pack performance of a four-cylinder diesel engine.

Abstract In order to maximize the reluctance torque component, multiple-layer flux barriers are usually employed in permanent magnet-assisted synchronous reluctance (PMAREL) motors. However, the permanent magnet (PM) dimension of each layer should be carefully designed to achieve the best performance with the minimum PM material. This article investigates this issue and proposes a method to define the PM width according to the sinusoidal no-load airgap flux density distribution. First, the accuracy of the no-load magnetic circuit for airgap flux density calculation is verified with finite element analysis (FEA), considering single or multiple flux-barriers per pole. The effects of the location, width, and thickness of the PM are investigated separately. Then the PM width is derived by the equations developed from the no-load magnetic circuit. The proposed method reduces both the PM mass and the torque ripple.

Abstract Linear internal combustion engine-linear generator integrated system (LICELGIS) is an innovative energy conversion device with the ability of converting mechanical energy into electrical energy, which allows it to be a range extender for hybrid vehicles. This article presents a fundamental analysis for the steady-state operation of the LICELGIS, concentrating on electromagnetic force and motion characteristics. Simple assumptions are made to represent ideal gases instantaneous heat release and rejection. Based on assumptions, sensitivity analysis is carried out for key factors of electromagnetic force. The theoretical velocity model in mathematics is derived from analyzing the LICELGIS theory model. It shows that fuel injection quantity and stroke length are the most sensitive factors in key parameters. The piston velocity around the top dead center (TDC) changes greater than that at any other position, which is caused by the combustion process.

Abstract Mechanical friction simulations offer a valuable tool in the development of internal combustion engines for the evaluation of optimization studies in terms of time efficiency. However, system modeling and evaluation of model performance may be highly complex. A high number of interacting submodels and parameters as well as a limited model transparency contribute to uncertainties in the modeling process. In particular, model calibration and validation are complicated by the unknown effect of parameters on the model output. This article presents an advanced and model-independent methodology for identifying sensitive parameters of engine friction. This allows the user to investigate an unlimited number of parameters of a model whose structure and properties are prior unknown.

Abstract One of the key factors for accurate mass burn fraction and energy conversion point calculations is the accuracy of the compression ratio. The method presented in this article suggests a workflow that can be applied to determine or correct the compression ratio estimated geometrically or measured using liquid displacement. It is derived using the observation that, in a motored engine, the heat losses are symmetrical about a certain crank angle, which allows for the derivation of an expression for the clearance volume [1]. In this article, a workflow is implemented in real time, in a current production engine indicating system. The goal is to improve measurement data quality and stability for the energy conversion points calculated during measurement procedures. Experimental and simulation data is presented to highlight the benefits and improvement that can be achieved, especially at the start of combustion.

Abstract With the introduction of advanced lightweight materials with complex microstructures and behaviors, more focus is put on the accurate determination of their forming limits, and that can only be possible through experiments as the conventional theoretical models for the forming limit curve (FLC) prediction fail to perform. Despite that, CAE engineers, designers, and toolmakers still rely heavily on theoretical models due to the steep costs associated with formability testing, including mechanical setup, a large number of tests, and the cost of a stereo digital image correlation (DIC) system. The international standard ISO 12004-2:2021 recommends using a stereo DIC system for formability testing since two-dimensional (2D) DIC systems are considered incapable of producing reliable strains due to errors associated with out-of-plane motion and deformation.

Abstract Turbocharging can provide a low cost means for increasing the power output and fuel economy of an internal combustion engine. Currently, turbocharging is common in multi-cylinder engines, but due to the inconsistent nature of intake air flow, it is not commonly used in single-cylinder engines. In this article, we propose a novel method for turbocharging single-cylinder, four-stroke engines. Our method adds an air capacitor-an additional volume in series with the intake manifold, between the turbocharger compressor and the engine intake-to buffer the output from the turbocharger compressor and deliver pressurized air during the intake stroke. We analyzed the theoretical feasibility of air capacitor-based turbocharging for a single-cylinder engine, focusing on fill time, optimal volume, density gain, and thermal effects due to adiabatic compression of the intake air.