Search Results

Abstract This article discusses a multi-item planning and scheduling problem in a job-shop system with consideration of energy consumption. Planning is considered by a set of periods, each one is characterized by a demand, energy, and length. Scheduling is determined by the sequences of jobs on available resources. A Mixed-Integer Linear Programming (MILP) problem is formulated to integrate planning and scheduling, it is considered as an NP-difficult problem. A Genetic Algorithm (GA) is then developed to solve the MILP, and then a hybridized approach of simulated annealing with genetic algorithm (HGASA) is presented to optimize the results. Finally, numerical results are presented and analyzed to evaluate the effectiveness of the proposed algorithms.

Abstract Lightweight and high-strength high-pressure die casting (HPDC) aluminum has been widely used in automotive components such as the cylinder block, lower crankcase extension, transmission case, and drive unit. Die cast parts have good surface finishes with relatively higher material strength in the casting skin than the center core material, maintain consistent features and tolerance, and maximize metal yield, therefore making it the most cost-effective casting process for mass production of aluminum parts. However, due to the rapid filling rates, the HPDC process tends to form large porosity and oxides because of the entrapped gas and solidification shrinkage, thereby deteriorating the mechanical properties of the casting parts.

Abstract Tailored blanks offer great lightweighting opportunities for automotive industry and were applied on the front rails of a sedan in this research. To achieve the most efficient material usage, all the front rail parts were tailored into multiple sheets with the gauge of each sheet defined as a design variable for optimization. The equivalent static loads (ESL) method was adopted for linear optimization and the Insurance Institute for Highway Safety (IIHS) moderate overlap frontal crash as the nonlinear analysis load case. The torsion and bending stiffness of the sedan body in white (BIW) were set as design constraints. The occupant compartment intrusion in IIHS moderate overlap front crash was set as design objective to be minimized. The optimal thickness configuration for the tailored front rail designs was obtained through ESL optimization for multiple mass saving targets.

Abstract In this article, the crashworthiness of a locomotive is assessed through finite element analysis (FEA). The present investigation is focused on the analysis of a locomotive with driving cab to improve the modeling approach and exploring the intrinsic structural weaknesses to improve its crashworthiness. The analyses are conducted according to the EN 15227 standard, which provide crashworthiness requirements for locomotive structure. The finite element model is validated in terms of acceleration and energy balance by the experimental results. The validated model is further used to assess the crashworthiness behavior at a higher impact speed, that is, 100, 160, and 225 km/hr. It has been noticed that local buckling occurs at different points, which reduces the desired progressive damage behavior in the locomotive. The results indicate that at higher speed, large plastic deformation occurs in the frontal part of the locomotive.

Abstract New analytical structural stress solutions for a rigid inclusion in a finite square thin plate with clamping edges under opening loading conditions are developed. The new solutions are used to derive new analytical structural stress and stress intensity factor solutions for similar and dissimilar spot welds in cross-tension specimens. Three-dimensional finite element analyses are conducted to obtain the stress intensity factor solutions for similar spot welds and dissimilar magnesium/steel spot welds in cross-tension specimens of equal thickness with different ratios of half-specimen width-to-weld radius. A comparison of the analytical and computational solutions indicates that the analytical stress intensity factor solutions for similar spot welds in cross-tension specimens of equal thickness are accurate for large ratios of half-specimen width-to-weld radius.

Abstract The paper presents a complete description of the design and manufacturing of a Carbon Fiber/epoxy mold with an embedded Carbon Fiber resistor heater, and the mold performances in terms of its surface temperature distribution and thermal deformations resulting from the heating. The mold was designed for manufacturing aileron skins from Vacuum Bag Only prepreg cured at 135°C. The glass transition temperature of the used resin-hardener system was about 175°C. To ensure homogenous temperature of the mold working surface in the course of curing, the Carbon Fiber heater was embedded in a layer of a highly heat-conductive cristobalite/epoxy composite, forming the core of the mold shell. Because the cristobalite/epoxy composite displayed much higher thermal expansion than CF/epoxy did, thermal stresses could arise due to this discrepancy in the course of heating.

Abstract Cavitation erosion caused by high-frequency vibrating walls can appear in the cooling circuit of internal combustion engines along the liners. The vibrations caused by the mechanical forces acting on the crank drive can lead to temporary regions of low pressure in the coolant with local vapor formation, and vapor collapse close to the liner walls leads to erosion damage, which can strongly reduce the lifetime of the entire engine. The experimental investigation of this phenomenon is so time consuming and expensive, which it is usually not feasible during the design phase. Therefore, numerical tools for erosion damage prediction should be preferred. This study presents a numerical workflow for the prediction of cavitation erosion damages by coupling a three-dimensional (3D) Multi-Body-Dynamic (MBD) simulation tool with a 3D Computational Fluid Dynamics (CFD) solver.

Abstract The present study deals with the investigation on microstructural and mechanical properties of friction stir processed (FSPed) pure Aluminum (Al)-Graphene Nanoplatelets (GNPs) composites. Composite specimens such as castings were made by blending 0.5 wt.%, 1.0 wt.%, 1.5 wt.%, and 2.0 wt.% of GNPs in pure Al matrix using the ultrasonic-assisted stir casting technique (UASCT). Also for enhancement of mechanical properties via grain refinement the friction stir processing (FSP) has been employed, as well as mechanical properties like tensile strength and microhardness were evaluated. Moreover, the microstructural analysis were done using Scanning Electron Microscope (SEM), Field Emission Scanning Electron Microscope (FESEM), transmission electron microscopy (TEM), and X-Ray Diffraction (XRD) examination were also performed for inspecting the changes occurred during synthesis of the fabricated composites after FSP.

Abstract High-cycle fatigue (HCF) is one of the main concerns for spot-welded structures, and finite element (FE)-based simulations have critical importance for the life assessment and design optimization. The accuracy of spot weld modeling methodologies has a key role in achieving the development objectives. This article presents a comparative study for HCF simulations of different spot weld modeling methodologies and their comparison with the test data. In this regard, HCF analyses based on Findley’s multi-axial damage model are conducted with a commercial software. Direct equivalenced spot weld modeling with and without offset adjustment, rigid spot weld, and rigid beam (single) spot weld methods are analyzed for overlapped sheet metals under axial cyclic loading. Two specimens with different thicknesses, spot weld diameters, and number of nuggets are simulated under six cyclic load cases: 2000-4000 N, 1400-2800 N, 1800-3600 N, 200-8000 N, 100-8300 N, and 200-6800 N.

Abstract A current automotive frame did not absorb energy efficiently during a vehicle frontal crash test. To solve this problem, the finite element model was established. The accuracy of the established model was verified through a real vehicle crash test. Then the orthogonal design of the experiment was conducted. The thicknesses of the outer and inner plates of front anti-collision beams, connecting brackets, and outer and inner plates of front rails were selected as variables. Then the optimum combination of variables was determined by applying gray relational theory. The results showed that the optimized frame can absorb more impact energy than the original design. Maximum deceleration of the lower part of the B-pillar decreased significantly during a frontal crash. Thus the problem of excessive deformation of the rails was solved, and the proposed method can be applied to the optimization of vehicle crashworthiness.

Abstract With increased consumer demand for fuel efficient vehicles as well as more stringent greenhouse gas regulations and/or Corporate Average Fuel Economy (CAFE) standards from governments around the globe, the automotive industry, including the OEM (Original Equipment Manufacturers) and suppliers, is working diligently to innovate in all areas of vehicle design. In addition to improving aerodynamics, enhancing internal combustion engines and transmission technologies, and developing alternative fuel vehicles, mass reduction has been identified as an important strategy in future vehicle development. In this article, the development, analysis, and experiment of multi-cornered structures are presented. To achieve mass reduction, two non-traditional multi-cornered structures, with twelve- and sixteen-cornered cross-sections, were developed separately by using computer simulations.

Abstract A rear underrun protection device (RUPD) plays a fundamental role in reducing the risk of running a small car beneath the rear or the side of a heavy truck because of the difference in structure heights in the event of a vehicle collision. Even in cars with five-star safety ratings, crashing into a truck with poorly designed RUPD results in a passenger compartment intrusion (PCI) more than the maximum allowable limit as per the United States (US) American National Highway Traffic Safety Administration (NHTSA) standards Federal Motor Vehicle Safety Standard (FMVSS). In this article, mild steel was used to fabricate the new designs of RUPD. The design was analyzed using finite element (FE) analysis LS-DYNA software. Simulations of a Toyota Yaris 2010 and Ford Taurus 2001 were performed at a constant speed of 63 km/h at the time of impact. The ability to prevent severe injuries in a collision with the rear side of the truck was estimated to optimize the underrun design.

Abstract Powder metallurgy is a widely used manufacturing methodology in the gearbox industry. Noise and vibration is a common cause for concern in the gearbox industry due to the continuous contact between gear teeth at high rotational frequencies. Despite this, limited research has been performed investigating the modal properties of powder metal products. This work investigates the damping ratios of a copper-infiltrated steel powder metal ring and a hot-rolled steel ring both experimentally and computationally. Negligible difference was observed between the damping ratios of the powder metal and hot-rolled steel rings. Two proportional damping models were investigated to predict the damping ratios of the powder metal ring. It was found that the Caughey damping model was the most accurate, generating damping ratios within 2.36% for a frequency bandwidth of up to 4000 Hz.

Abstract Research and development efforts in the automotive industry have been long focused on crashworthy, durable vehicles with the lowest mass possible as higher mass requires more energy and, thus, causes more CO2 emissions. One way of approaching these objectives is to reduce the total vehicle weight by using higher strength-to-weight ratio materials, such as Advanced High-Strength Steels (AHSS). Typically, as the steel gets stronger, its formability is reduced. The steel industry has been long developing (so-called) third-generation (Gen3) AHSS for the automotive industry. These grades offer higher formability compared to first-generation (Gen1) and cost less compared to the second-generation (Gen2) AHSS. Transformation Induced Plasticity (TRIP)-aided Bainitic Ferrite (TBF) and Quenching and Partitioning (Q&P) steel families are considered to be the Gen3 AHSS.

Abstract Cast magnesium (Mg) door inner panels can provide a good combination of weight, functional, manufacturing, and economical requirements. However, several challenges exist including casting technology for thin-wall part design, multi-material incompatibility, and relatively low strength versus steel. A project was supported by the US Department of Energy to design and develop a lightweight frame-under-glass door having a thin-wall, full die-cast, Mg inner panel. This development project is the first of its kind within North America. The 2.0 mm Mg design, through casting process enablers, has met or exceeded all stiffness and side-impact requirements, with significant mass reduction and part consolidation. In addition, a corrosion mitigation strategy has been established using industry-accepted galvanic isolation methods and coating technologies. The performance of the Mg design has been demonstrated through component and vehicle tests.

Abstract Combining ball milling with stir casting in the synthesis of nanocomposites is found effective in increasing the strength and ductility of the nanocomposites. In the first step, the nanoparticles used as reinforcement are generated by milling a mixture of aluminum (Al) and manganese dioxide (MnO2) powders. A mixture of Al and MnO2 powders are mixed in the ratio of 1:2.4 by weight and milled at 300 rpm in a high-energy planetary ball mill for different durations of 120 min, 240 min, and 360 min to generate nano-sized alumina (Al2O3) particles. It is supposed that the powders have two different roles during milling, firstly, to generate nano-sized Al2O3 by oxidation at the high-energy impact points due to collision between Al and MnO2 particles, and secondly, to keep nano-sized Al2O3 particles physically separate by the presence of coarser particles.

Abstract Reducing the friction of the internal combustion engine (ICE) is of major interest to reduce fuel consumption and greenhouse gas (GHG) emissions. A huge potential for friction reduction is seen in the piston ring-cylinder liner (PRCL) coupling. Approaching the cylindrical liner shape in the hot operation state will enhance the PRCL conformation. Recently, newly developed freeform honing techniques can help to achieve this perfect cylinder shape. This article presents a numerical study of the effect of freeform honing on the geometrical performance of the liner in the hot operation state. The freeform honed liner (TR) concept is based on the approach of reversing the local deformation of a conventional circular liner. A validated computational model for a gasoline engine is used to compare the geometrical performance of those TR cases with circular, elliptical (EL), and conical elliptical liners (NEL) at different operational points.

Abstract In this article, the effect of heat treatment on the microstructure and mechanical behavior of medium-carbon steel wire intended for the spring mattress is investigated using scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), X-ray diffraction, Vickers hardness (Hv), and tensile strength. The results indicate that the microstructure elongation along the wire axis is observed with the bending and kinking lamellae at the deformation level of 57.81%, this change appears as a fracture in the microstructure and leads to an increase in hardness, tensile strength, and intensities of diffraction patterns. After heat treatment, we observed a redistribution in the grain, which is almost the same in the wire rod and drawn wires; indeed, this led to a decrease in hardness, tensile strength, and augmentation in intensities of peaks. The EBSD pole figures reveal the development of texture in the cementite slip plane (001).

Abstract Fatigue performance can be a critical attribute for the production of structural parts or components via additive manufacturing (AM). In comparison to the static tensile behavior of AM components, there is a lack of knowledge regarding the fatigue performance. The growing market demand for AM implies the need for more accurate fatigue investigations to account for dynamically loaded applications. A357.0 parts are processed by laser-based powder bed fusion (L-PBF) in order to evaluate the effect of surface finishing on fatigue behavior. The specimens are surface finished by shot peening using ϕ = 0.2 and ϕ = 0.4 mm steel particles and ϕ = 0.21-0.3 mm zirconia-based ceramic particles.

Abstract The present study aims to join the dissimilar materials such as Dual-Phase (DP) 600 Steel and AA6082-T6 Aluminum (Al) alloy via the friction stir welding (FSW) process with a reduced intermetallic compound (IMC) layer. The five different tool tilt angles of 0°, 0.5°, 1°, 1.5°, and 2° were selected to fabricate the joints. The weld characteristics such as tensile strength, hardness, macrostructure, and microstructure were analyzed. The weld interface was studied by employing an optical microscope and scanning electron microscope (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD) techniques. The joint produced with a 0.5° tilt angle has achieved the highest ultimate tensile strength (UTS) of 240 MPa. The IMCs were identified as Fe2Al8 and FeAl2 from the joint interface studies.