Search Results

Abstract In recent years, lean-burn gasoline Spark-Ignition (SI) engines have been a major subject of investigations. With this solution, in fact, it is possible to simultaneously reduce NOx raw emissions and fuel consumption due to decreased heat losses, higher thermodynamic efficiency, and enhanced knock resistance. However, the real applicability of this technique is strongly limited by the increase in cyclic variation and the occurrence of misfire, which are typical for the combustion of homogeneous lean air/fuel mixtures. The employment of a Pre-Chamber (PC), in which the combustion begins before proceeding in the main combustion chamber, has already shown the capability of significantly extending the lean-burn limit. In this work, the potential of an ultralean PC SI engine for a decisive improvement of the thermal efficiency is presented by means of numerical and experimental analyses.

Abstract Due to the increasing requirements for efficiency, the wide range of characteristics and the improved possibilities of modern development and production processes, compressors in turbochargers have become more individualized in order to adapt to the requirements of internal combustion engines. An understanding of the working mechanisms as well as an understanding of the way that losses occur in the flow allows a reduced development effort during the optimization process. This article presents three-dimensional (3D) Computational Fluid Dynamics (CFD) investigations of the loss mechanisms and quantitative calculations of individual losses. The 3D-CFD method used in this article will reduce the drawbacks of one-dimensional calculation as far as possible. For example, the twist of the blades is taken into account and the “discrete” method is used for loss calculation instead of the “average” method.

Abstract The article presents a concept of a new turbine engine in the field of pressure gain combustion (PGC). The engine operates according to the Humphrey thermodynamic cycle, where pressure increase was obtained in a combustion chamber closed with a valve. The intake mushroom valve and exhaust swing valve were designed for self-acting. They operate as a result of gas pressure and centrifugal force. The engine consists of two rotating combustion chambers and a counterrotating radial turbine, in both of which mechanical power was generated. The gas flow in the mobile valve system, combustion process, gas expansion, and torque generation were analyzed by means of Computational Fluid Dynamics (CFD) analysis. The investigated engine concept is characterized by significant energy efficiency.

Abstract The cold crank-start stage, including the first three engine cycles, is responsible for a significant amount of the cold-start phase emissions in a Gasoline Direct Injection (GDI) engine. The engine crank-start is highly transient due to substantial engine speed changes, Manifold Absolute Pressure (MAP) dynamics, and in-cylinder temperatures. Combustion characteristics change depending on control inputs variations, including throttle angle and spark timing. Fuel injection strategy, timing, and vaporization dynamics are other parameters causing cold-start first cycles analysis to be more complex. Hybrid Electric Vehicles (HEVs) provide elevated cranking speed, enabling technologies such as cam phasing to adjust the valve timing and throttling, and increased fuel injection pressure from the first firings.

Abstract With the introduction of advanced lightweight materials with complex microstructures and behaviors, more focus is put on the accurate determination of their forming limits, and that can only be possible through experiments as the conventional theoretical models for the forming limit curve (FLC) prediction fail to perform. Despite that, CAE engineers, designers, and toolmakers still rely heavily on theoretical models due to the steep costs associated with formability testing, including mechanical setup, a large number of tests, and the cost of a stereo digital image correlation (DIC) system. The international standard ISO 12004-2:2021 recommends using a stereo DIC system for formability testing since two-dimensional (2D) DIC systems are considered incapable of producing reliable strains due to errors associated with out-of-plane motion and deformation.

Abstract A modular, stationary IC engine blow rig for differential and integral flow field measurements using particle image velocimetry (PIV) has been developed. Unlike conventional PIV blow rigs, the given design is capable of operating under near-reality charge air conditions, that is, highly pressurized, hot intake air supply at high flow rates. Its conceptual flexibility as well as peripheral infrastructure allow for comprehensive and wide-ranging flow field analysis. Because of a modular architecture, it is neither confined to a specific cylinder head design nor limited solely to the application of PIV for differential flow field analysis. It also already accounts for direct inlet flow determination through an additional PIV access point upstream of the cylinder head. The inlet and outlet ducts have been designed with regular shapes and smooth walls, such that a digital twin-type CFD model of the blow rig is conveniently feasible.

Abstract Stratified lean combustion has proven to be a promising approach for further increasing the thermal efficiency of gasoline direct injection engines in low load conditions. In this work, a new injection strategy for stratified operation mode is introduced. A side and a central-mounted solenoid multi-hole injector are simultaneously operated in a single-cylinder engine. Thermodynamic investigations show that this concept leads to improved stability, faster combustion, reduced particle number emissions, and lower fuel consumption levels compared to using only one injector. Experiments at an optical engine and three-dimensional computational fluid dynamics (CFD) simulations explain the improvements by a more compact mixture and reduced piston wetting with two injectors. Finally, the application of external EGR in combination with the above concept allows NOx emissions to be effectively kept at a low level while maintaining a stable operation.

Abstract Realizing the potential of the gasoline direct injection (GDI) concept lies in effectively stratifying the charge at different engine operating conditions. This is generally obtained by properly directing the air and fuel through carefully oriented intake port(s) and fuel spray and appropriately changing injection parameters. However, robust methods of charge stratification are essential to extend the lean operating range, particularly in small GDI engines. In this work, a novel piston shape was developed for a 200 cm3, single-cylinder, four-stroke gasoline engine to attain charge stratification. Stratification of charge is achieved even when the fuel was injected early in the intake stroke by a specially shaped wedge on the piston crown that produced twin vortices during compression and physically separated the charge into two sides in the combustion chamber.

Abstract The braking phenomenon is an aspect of vehicle stopping performance where with kinetic energy due to the speed of the vehicle is transformed into thermal energy produced by the brake disc and its pads. The heat must then be dissipated into the surrounding structure and into the airflow around the brake system. The thermal friction field during the braking phase between the disc and the brake pads can lead to excessive temperatures. In our work, we presented numerical modeling using ANSYS software adapted in the finite element method (FEM), to follow the evolution of the global temperatures for the two types of brake discs, full and ventilated disc during braking scenario. Also, numerical simulation of the transient thermal analysis and the static structural analysis were performed here sequentially, with coupled thermo-structural method.

Abstract Electromagnetic forming (EMF) is a high-speed impulse forming process developed during the 1950s and 1960s to acquire shapes from sheet metal that could not be obtained using conventional forming techniques. In order to attain required deformation, EMF process applies high Lorentz force for a very short duration of time. Due to the ability to form aluminum and other low-formability materials, the use of EMF of sheet metal for automobile parts has been rising in recent years. This review gives an inclusive survey of historical progress in EMF of continuum sheet metals. Also, the EMF is reviewed based on analytical approach, finite element method (FEM) simulation-based approach and experimental approach, on formability of the metals.

Abstract Applying a suitable design optimization technique is a crucial task for optimizing compression ignition engines because of the time-consuming process of optimization even with advanced supercomputers. Traditional computational fluid dynamics (CFD) used in conjunction with design of experiment (DOE) methods requires executing the CFD model several times. A response surface is usually fitted to relate the inputs to the outputs, which is often created based on linear regression. This method is not well suited to capture interaction effects between inputs and nonlinearities existing during engine combustion. A combination of genetic algorithm (GA) and CFD tools usually eventuates better optimum results. However, the CFD simulations must be executed sequentially, resulting in extremely high computational times, which makes it impossible to apply an optimization study using a single desktop computer.

Abstract Improving the aerodynamics of heavy trucks is an important consideration in the strive for more energy-efficient vehicles. Cooling drag is one part of the total aerodynamic resistance acting on a vehicle, which arises as a consequence of air flowing through the grille area, the heat exchangers, and the irregular under-hood area. Today cooling packages of heavy trucks are dimensioned for a critical cooling case, typically when the vehicle is driving fully laden, at low speed up a steep hill. However, for long-haul trucks, mostly operating at highway speeds on mostly level roads, it may not be necessary to have all the cooling airflow from an open-grille configuration. It can therefore be desirable for fuel consumption purposes, to shut off the entire cooling airflow, or a portion of it, under certain driving conditions dictated by the cooling demands. In Europe, most trucks operating on the roads are of cab-over-engine type, as a consequence of the length legislations present.

Abstract The transient surface pressure over a full-scale, operational compact automotive vehicle—a Volkswagen Golf 7—exposed to transient crosswinds with relative yaw angles of β = 22-45° has been characterized. Experiments were performed at the BMW side-wind facility in Aschheim, Germany. Measurements of the incoming flow in front of the car were taken with eleven five-hole dynamic pressure probes, and separately, time-resolved surface pressure measurements at 188 locations were performed. Unsteady characteristics (not able to be identified in quasi-steady modelling) have been identified: the flow in separated regions on the vehicle’s leeward side takes longer to develop than at the windward side, and spatially, the vehicle experiences local crosswind as it gradually enters the crosswind.

Abstract In this article, a methodology is presented to assess the influence of time-averaged deformations on a production car of the 2018 A-class due to wind load. Exemplary, the deformations of the front and rear bumper are investigated. The aerodynamic development of vehicles at Mercedes-Benz is divided into several phases. When comparing, force coefficients differences can be observed between these distinct hardware stages as well as when comparing steady-state simulations to wind tunnel measurements. In early phases when prototype vehicles are not yet available, so-called aero foam models are used. These are well-defined full-sized vehicle models as the outer skin is milled from Polyurethane. Important aerodynamic characteristics such as an engine compartment with a cooling module, deflecting axles with rotatable wheels, and underbody covers are represented.

Abstract A tire is one of the most essential parts of a vehicle that not only helps to provide stability but also helps in isolating shocks from the road surface as well as giving longitudinal and lateral powers for vehicle acceleration, steering, and braking. We are familiar with the tire as a pneumatic tire, but with recent developments, a new category of tires called non-pneumatic tires (NPT) has recently come to light. The unique design equipped for these tires provides them with several advantages over the conventional pneumatic tires, which include the elimination of tire blowouts and elimination of punctures. Since rotating tires are known to contribute up to one-third of the vehicle’s total aerodynamic force [5] and also because of the vast advantages provided by the NPT.

Abstract We come across multiphase flow (oil and air) in many applications in automotive, aerospace, marine, chemical, and power grid industries. The present study presents a model that describes the flow of oil and air through an orifice from one chamber to another based on gravity, viscosity, and density difference. The aim of this study is to provide a simulation technique that finds the total time required for the complete percolation of oil/air to drain out from the respective chambers. This technique uses the Volume Of Fluid (VOF) using the Computational Fluid Dynamics (CFD) software STAR CCM+. VOF technique is a multiphase model and is very effective in determining the free-surface phenomenon. This technique uses an implicit unsteady and k-ε turbulence model at ambient conditions. Test results validate the CFD analysis. There is a good agreement between the simulation and test results.

Abstract In this article, an improved brake cooling simulation method is introduced. By this method, the vehicle parameters, such as weight, height of the center of gravity, wheelbase, and the like can be included to calculate the braking thermal load under different operating conditions. The effect of the brake kinetic energy regeneration (BKER) on the braking thermal load can also be calculated by this method. The calculated braking thermal load is then input to a coupled 3D simulation model to conduct flow and thermal simulation to calculate brake disc temperature. It is demonstrated that by this simulation method, the difference between the brake disc temperatures obtained from simulation and vehicle test can be controlled below 5%.

Abstract The appearance of an automobile is anything but unimportant for the owner. This applies to the acquisition as well as the keeping. In this context, the avoidance of corrosion is a fundamental part of the user’s satisfaction of a company. The body design can be modified to optimize drainage and reduce the risk of corrosion, improving the owner’s satisfaction with the purchase of the automobile. During the proof of concept of water management, as part of the process of development, physical prototypes are state of the art. At this point in the development process, every necessary change is expensive and time consuming. Virtual methods are able to support the development in earlier steps and thus reduce costs. The conventional Computational Fluid Dynamics (CFD) methods could not handle the simulation of a full car in the rain or water passage properly due to much higher computation efforts and deviations from the experiments.

Abstract New analytical structural stress solutions for a rigid inclusion in a finite square thin plate with clamping edges under opening loading conditions are developed. The new solutions are used to derive new analytical structural stress and stress intensity factor solutions for similar and dissimilar spot welds in cross-tension specimens. Three-dimensional finite element analyses are conducted to obtain the stress intensity factor solutions for similar spot welds and dissimilar magnesium/steel spot welds in cross-tension specimens of equal thickness with different ratios of half-specimen width-to-weld radius. A comparison of the analytical and computational solutions indicates that the analytical stress intensity factor solutions for similar spot welds in cross-tension specimens of equal thickness are accurate for large ratios of half-specimen width-to-weld radius.

Abstract In automotive, the use of heavy structure leads to high consumptions of fuel and resulting high exhaust (CO2) emissions. To curb this problem, nowadays, the conventional steel used for years in automotive structures is currently replaced with other different lightweight materials such as aluminum, magnesium, glass fiber-reinforced polymer, carbon fiber-reinforced polymer, titanium, and so on. On the other hand, compared to the known steel properties and performances, these lightweight materials offer challenging issues related to life cycle, recycling, cost, and manufacturing. But, more than sometimes, reaching the same levels of performances with materials different from steel presents huge difficulties. This represents the cause of researching strategies and techniques to optimize the material distribution and the performances of a component, saving material and consequently reducing weight.