Search Results

This work involved study of the effects of alcohol blends on combustion, fuel economy and emissions in a single cylinder research engine equipped with a mechanical fully variable valvetrain on the inlet and variable valve timing on the exhaust. A number of splash blends of gasoline, iso-octane, ethanol and butanol were examined during port fuel injected early inlet valve closing operation, both with and without variable valve timing. Under low valve overlap conditions, it was apparent that the inlet valve durations/lifts required for full unthrottled operation were remarkably similar for the wide range of blends studied. However, with high valve overlap differences in burning velocities and internal EGR tolerances warranted changes in these valve settings.

This work was concerned with evaluation of the performance and emissions of potential future biofuels during advanced spark ignition engine operation. The fuels prepared included three variants of gasoline, three gasoline-ethanol blends and a gasoline-butanol fuel altogether covering a range of oxygen mass concentrations and octane numbers to identify key influencing parameters. The combustion of the fuels was evaluated in a turbocharged multi-cylinder direct fuel injection research engine equipped with a standard three-way catalyst and an external EGR circuit that allowed use of either cooled or non-cooled EGR. The engine operating effects studied at both part and boosted high load conditions included fuel injection timing and pressure, excess air tolerance, EGR tolerance and spark retard limits. A number of blends were also mapped at suitable sites across the European drive cycle under downsized engine conditions.

Through improving the 48V hybrid vehicle archetype, governmental emission targets could be more easily met without incurring the high costs associated with increasing levels of electrification. The braking energy recovery function of hybrid vehicles is recognised as an effective solution to reduce emissions and fuel consumption in the short to medium term. The aim of this study was to evaluate methods to maximise the braking energy recovery capability of the 48V hybrid electric vehicle over pre-selected drive cycles using appropriately sized electrified components. The strategy adopted was based upon optimising the battery chemistry type via specific power capability, so that overall brake power is equal to the maximum battery charging power in a typical medium-sized passenger car under typical driving. This will maximise the regenerative braking energy whilst providing a larger torque assistance for a lower battery capacity.

This experimental work was concerned with the combination of internal EGR with an early inlet valve closure strategy for improved part-load fuel economy. The experiments were performed in a new spark-ignited thermodynamic single cylinder research engine, equipped with a mechanical fully variable valvetrain on both the inlet and exhaust. During unthrottled operation at constant engine speed and load, increasing the mass of trapped residual allowed increased valve duration and lift to be used. In turn, this enabled further small improvements in gas exchange efficiency, thermal efficiency and hence indicated fuel consumption. Such effects were quantified under both port and homogeneous central direct fuel injection conditions. Shrouding of the inlet ports as a potential method to increase in-cylinder gas velocities has also been considered.

The work examined the practicality of converting a modern production 6 cylinder 7.7 litre heavy-duty diesel engine for flex dual-fuel operation with ammonia as the main fuel. A small amount of diesel fuel (pilot) was used as an ignition source. Ammonia was injected into the intake ports during the intake stroke, while the original direct fuel injection equipment was retained and used for pilot diesel injection. A bespoke engine control unit was used to control the injection of both fuels and all other engine parameters. The aim was to provide a cost-effective retrofitting technology for existing heavy-duty engines, to enable eco-friendly operation with minimal carbon emissions. The tests were carried out at a baseline speed of 600 rpm for the load range of the engine (10-90%), with minimum pilot diesel quantity and as high as 90% substitution ratio of ammonia for diesel fuel.

The work was concerned with the use of exhaust gas recirculation to minimise CO2 and pollutant emissions over a wide operating range in a multi-cylinder research engine. Under part-load conditions a combination of internal and external EGR was used to invoke controlled auto ignition combustion and improve fuel consumption. Outside the CAI regime, small additional fuel savings could be made by employing reduced EGR rates in spark ignition combustion mode. At boosted high load conditions a comparison of excess fuel, excess air and cooled external EGR charge dilution was made. It was apparent that cooled EGR was a more effective suppressant of knock than excess air, with combustion phasing further advanced towards the optimum and improved combustion stability achieved over a wider operating range. The full load emissions reduction potential of EGR was also demonstrated, with emissions of CO2 reduced by up to 17% and engine-out HC and CO decreased by up to 80%.

Ammonia (NH3) is emerging as a potential fuel for longer range decarbonised heavy transport, predominantly due to favourable characteristics as an effective hydrogen carrier. This is despite generally unfavourable combustion and toxicity attributes, restricting end use to applications where robust health and safety protocols can always be upheld. In the currently reported work, a spark ignited thermodynamic single cylinder research engine was upgraded to include gaseous ammonia and hydrogen port injection fueling, with the aim of understanding maximum viable ammonia substitution ratios across the speed-load operating map. The work was conducted under stoichiometric conditions with the spark timing re-optimised for maximum brake torque at all stable logged sites. The experiments included industry standard measurements of combustion, performance and engine-out emissions.

Two different TEM (Transmission Electron Microscopy) grids - graphene oxide (GO) and silicon nitride (SiN) - were used to capture the particulates emitted with the exhaust of a modern 1.0 L GDI (Gasoline Direct Injection) engine. One speed-load condition (1250 rpm – idle) was chosen to generate a nanometric particulate output in the sub-23 nm regime which has been traditionally difficult to analyse in terms of composition and morphology. The overall aim was to understand if additional benefits can be obtained by analysing the particles captured in the exhaust on a nanoporous silicon nitride grid compared to state-of- the-art graphene oxide grids. The behaviour of porous SiN support films was of interest since nanopores are present in the grid in the 20 nm regime and the material is thermally and dimensionally stable under high temperatures, allowing thermophoretic capture directly within the engine exhaust stream.

This work was concerned with increasing the attainable load during gasoline controlled auto-ignition combustion in a multi-cylinder direct fuel injection research engine. To extend the peak output under naturally aspirated conditions it proved favourable to combine internal and external exhaust gas recirculation under stoichiometric fuelled conditions. During turbocharged high load operation it was beneficial in terms of fuel economy to dilute the charge with a combination of internally re-circulated exhaust gases and excess air. Replacing a proportion of these diluents with externally re-circulated burned gases appeared to facilitate lower emissions of HC and CO. The highest load generated via boost was limited by increasing peak in-cylinder pressure and falling gas exchange efficiency. Regardless, the use of boost increased the load at which CAI could be invoked without lean NOx after-treatment.

The work was concerned with applying cooled EGR for improved high load fuel economy and reduced pollutant emissions in a turbocharged gasoline engine. While the thermodynamic benefits of EGR were clear, challenges remain to bring the technique to market. A comparison of pre and post compressor EGR supply indicated that post-compressor routing allowed higher compressor efficiencies to be maintained and hence reduced compressor work as the mass flow of EGR was increased. However, with this post-compressor routing, attaining sufficient EGR rate was not possible over the required operating map. Furthermore, at higher engine speeds where the pre-turbine exhaust pressure was greater than the intake plenum pressure, the timing of peak in-cylinder pressure was not as readily advanced towards the optimum.

An experimental study has been carried out with the end goal of minimizing engine-out methane emissions with Premixed Micro Pilot Combustion (PMPC) in a natural gas-diesel Dual-Fuel™ engine. The test engine used is a heavy-duty single cylinder engine with high pressure common rail diesel injection as well as port fuel injection of natural gas. Multiple variables were examined, including injection timings, exhaust gas recirculation (EGR) percentages, and rail pressure for diesel, conventional Dual-Fuel, and PMPC Dual-Fuel combustion modes. The responses investigated were pressure rise rate, engine-out emissions, heat release and indicated specific fuel consumption. PMPC reduces methane slip when compared to conventional Dual-Fuel and improves emissions and fuel efficiency at the expense of higher cylinder pressure.

The experimental work was concerned with improving understanding of the competing effects of the latent heat of vaporization and auto-ignition delay times of different ethanol blended fuels during heaving knocking combustion. The unique single cylinder SI engine employed included full bore overhead optical access capable of withstanding unusually high in-cylinder pressures. Heavy knock was deliberately induced under moderate loads using inlet air heating and a primary reference fuel blend of reduced octane rating. High-speed chemiluminescence imaging and simultaneous in-cylinder pressure data measurement were used to evaluate the combustion events. Under normal operation the engine was operated under port fuel injection with a stoichiometric air-fuel mixture. Multiple centered auto-ignition events were regularly observed, with knock intensities of up to ~40bar. Additional excess fuel of varied blend was then introduced directly into the end-gas in short transient bursts.

This work was concerned with use of two-stage cam profile switching to transition between SI and CAI combustion in a multi-cylinder direct fuel injection research engine. In order to achieve robust combustion mode changes, it proved necessary to switch the inlet and exhaust bank of tappets independently of one another. Practical issues addressed to improve tappet response included minimising tappet oil circuit dead volumes and reducing the oil pressure difference before and after a switch. When switching from SI to CAI combustion, it was possible to avoid misfire and operate the engine in a mixed-mode form of combustion. In addition, it was demonstrated that supplementary external EGR could be used to minimise transient peak knocking pressures during such transitions. Differences in overall engine noise levels during SI and CAI have also been qualified and some possible solutions are discussed.