Search Results

The present research explores the application of biodiesel fuel in a stationary agricultural engine operated under the Homogenous charge compression ignition (HCCI) mode. To achieve HCCI combustion, a fuel vaporizer and a high-pressure port fuel injection system are employed to facilitate rapid evaporation of the biodiesel fuel. The low volatility of biodiesel is one of the significant shortcomings, which makes it inevitable to use a fuel vaporizer at 380oC. Consequently, the charge temperature is high enough to promote advanced auto-ignition. Further, the high reactivity of biodiesel favors early auto-ignition of the charge. Besides, biodiesel exhibits a faster burn rate due to its oxygenated nature. The combined effect of advanced auto-ignition and faster burn rate resulted in a steep rise in the in-cylinder pressures, leading to abnormal combustion above 20% load. Diluting the charge reduces reactivity and intake oxygen concentration, facilitating load extension.

Premixed charged compression ignition (PCCI) is a promising low temperature combustion strategy for achieving a simultaneous reduction of oxides of nitrogen (NOx) and soot emissions in diesel engines. However, early direct injection results in a significant penalty in fuel economy, high unburned hydrocarbon (HC), and carbon monoxide (CO) emissions, especially in small-bore diesel engines. In the present work, computational fluid dynamic (CFD) investigations are carried out in a small-bore diesel engine using a commercial CFD software, CONVERGE. The computational models are validated with experimental results at two different load conditions, 20% and 40% of rated load. The validated models are used to carry out parametric investigations on the effects of fuel injection parameters, namely the start of fuel injection timing, injection pressure, and spray cone angle on PCCI combustion.

The presence of unsaturated methyl esters in biodiesel makes it susceptible to oxidation and fuel quality degradation upon long-term storage. In the present work, the effects of oxidation of Karanja biodiesel upon long-term storage on the combustion and emission characteristics of a heavy-duty truck diesel engine are studied. The Karanja biodiesel is stored for one year in a 200 litres steel barrel at room conditions to mimic commercial storage conditions. The results obtained show that compared to diesel, the start of injection of fresh and aged biodiesels are advanced by ~2-degree crank angle, and the ignition delay time is reduced. Aged biodiesel showed a slightly smaller ignition delay compares to fresh biodiesel. The fuel injection and combustion characteristics of fresh and aged biodiesels were similar at all the load conditions. Both fresh and aged biodiesels produced higher oxides of nitrogen (NOx) and lower smoke emissions compared to diesel.

For controlling oxides of nitrogen (NOx) and particular matter (PM) emissions from diesel engines, various fuel and combustion mode modification strategies are investigated in the past. Low temperature combustion (LTC) is an alternative combustion strategy that reduces NOx and PM emissions through premixed lean combustion. Dual fuel reactivity-controlled compression ignition (RCCI) is a promising LTC strategy with better control over the start and end of combustion because of reactivity and equivalence ratio stratification. However, the unburned hydrocarbon (HC) and carbon monoxide (CO) emissions are significantly higher in RCCI, especially at part-load conditions. The present work intends to address this shortcoming by utilizing oxygenated alternative fuels. Considering the limited availability and higher cost, replacing conventional fuels completely with alternative fuels is not feasible.

The present work investigates the effects of lowering the compression ratio (LCR) from 18:1 to 14:1 and optimizing the fuel injection parameters across the operating range of a mass production light-duty diesel engine. The results were quantified for a regulatory Indian drive cycle using a one-dimensional simulation tool. The results show that the LCR approach can simultaneously reduce the oxides of nitrogen (NOx) and soot emissions by 28% and 64%, respectively. However, the unburned hydrocarbon (HC) and carbon monoxide (CO) emissions increased significantly by 305% and 119%, respectively, with a 4.5% penalty in brake specific fuel consumption (BSFC). Hence, optimization of fuel injection parameters specific to LCR operation was attempted. It was evident that advancing the main injection timing and reducing the injection pressure at low-load operating points can significantly help to reduce BSFC, HC and CO emissions with a slight increase in the NOx emissions.

Extensive experimental investigations done over a decade in different engine types demonstrated the capability of achieving high efficiency along with low levels of oxides of nitrogen (NOx) and soot emissions with low temperature combustion (LTC) modes. However, the commercial application of LTC strategies requires several challenges to be addressed, including precise ignition timing control, reducing higher unburned hydrocarbon (UHC) and carbon monoxide (CO) emissions. The lower exhaust gas temperatures with LTC operation pose severe challenges for after-treatment control systems. Among the available LTC strategies, Reactivity Controlled Compression Ignition (RCCI) has emerged as the most promising strategy due to better ignition timing control with higher thermal efficiency. Nevertheless, the complexity of engine system hardware due to the dual fuel injection system and associated controls, high HC and CO emissions are the major limiting factors in RCCI.

Currently, alternative fuels produced from waste resources are gaining much attention to replace depleting fossil fuels. The disposal of waste plastic poses severe environmental problems across the globe. The energy embodied in waste plastics can be converted into liquid fuel by pyrolysis. The present work explores the possibility of utilizing waste plastic oil (WPO) produced from municipal plastic wastes and waste cooking oil (WCO) biodiesel produced from used cooking oil in a dual fuel reactivity-controlled compression ignition (RCCI) mode. A single-cylinder light-duty diesel engine used for agricultural water pumping applications is modified to run in RCCI through suitable intake and fuel injection systems modifications. Alternative fuel blends, viz. WPO and WCO biodiesel with 20 vol. % in gasoline and diesel is used as a port and direct-injected fuels in RCCI. The premixed ratio and direct-injected fuel timings are optimized to achieve maximum thermal efficiency.

Despite the advantages of turbocharging in improved engine performance and reduced exhaust emissions, commercial single-cylinder engines used for automotive applications remain naturally aspirated (NA) and are not generally turbocharged. This is due to the shortcomings with pulsated and intermittent exhaust gas flow into the turbine and the phase lag between the intake and exhaust stroke. In the present study, experimental investigations are initially carried out with a suitable turbocharger closely coupled to a single-cylinder diesel engine. Results indicated that the engine power dropped significantly by 40% for the turbocharged engine compared to the NA version even though the air mass flow rate was increased by at least 1.5 times with turbocharging. A novel approach of decoupling the turbine and the compressor and coupling them separately to the engine is proposed to address these limitations.

The carbon-neutral biodiesel is a promising renewable substitute for fossil diesel that renders the traditional oxides of nitrogen-particulate matter (NOx-PM) trade-off into a unidirectional NOx control problem. Low-temperature combustion (LTC) modes such as homogenous charge compression ignition (HCCI) are attractive for obtaining ultra-low NOx and PM emissions. Studies on utilizing biodiesel fuel for HCCI combustion mode are sparsely available. Moreover, biodiesel emulsions in the HCCI combustion mode have not been attempted so far. Based on this premise, the present work explored the potential to utilize biodiesel and its emulsions having 20% and 25% water by volume under HCCI operating conditions. Biodiesel was prepared from a non-edible Karanja oil. The biodiesel emulsions were prepared using a heated magnetic stirrer apparatus with 3% by volume of the raw Karanja oil as a surfactant.

Single-cylinder engines in mass production are generally not turbocharged due to the pulsated and intermittent exhaust gas flow into the turbocharger and the phase lag between the intake and exhaust stroke. The present work proposes a novel approach of decoupling the turbine and the compressor and coupling them separately to the engine to address these limitations. An impulse turbine is chosen for this application to extract energy during the pulsated exhaust flow. Commercially available AVL BOOST software was used to estimate the overall engine performance improvement of the proposed novel approach compared to the base naturally aspirated (NA) engine. Two different impulse turbine layouts were analyzed, one without an exhaust plenum and the second layout having an exhaust plenum before the power turbine. The merits and limitations of both layouts are compared in the present study.

Unsaturated methyl esters in biodiesel make it susceptible to oxidation and fuel quality degradation upon long-term storage. It is almost impossible to use biodiesel for commercial applications immediately after production. The lead time between biodiesel production and usage is generally high, causing auto-oxidation and fuel quality degradation. Hence any onsite improvement in fuel quality should be tested with aged biodiesel. To avoid the food versus fuel debate, non-edible oil feedstocks are preferable for producing biodiesel. However, biodiesel from non-edible oil sources has more unsaturated methyl ester constituents. The traditional trade-off between oxides of nitrogen (NOx) and soot emissions in conventional diesel combustion is reduced to a more severe NOx problem with biodiesel. In the present study, NOx mitigation through fuel modifications is studied for oxidized biodiesel produced from a non-edible oil, Karanja.

Over the years, much progress has been made in automotive vehicle technology to achieve high efficiency and clean combustion. Reactivity controlled compression ignition (RCCI) is one of the most widely studied high-efficiency, clean combustion strategies. However, complex dual-fuel injection systems and associated controls, high unburned hydrocarbon (UHC), and carbon monoxide (CO) emissions limit RCCI use in practical applications. Recently, single fuel RCCI strategies are gaining more attention as the above shortcomings are effectively addressed. Homogeneous charge with direct injection (HCDI) is a single fuel RCCI strategy that results in high thermal efficiency and lower UHC and CO emissions. In HCDI, the port-injected diesel fuel vapour and air are inducted during the intake stroke and ignited with direct-injected diesel fuel near the end of the compression stroke. However, high oxides of nitrogen (NOx) make HCDI less viable for practical applications.

Achieving stable combustion without misfire and knocking is challenging in premixed charge compression ignition (PCCI) especially in small bore, air cooled diesel engines owing to lower power output and inefficient cooling system. In the present study, a single cylinder, air cooled diesel engine used for agricultural water pumping applications is modified to run in PCCI mode by replacing an existing mechanical fuel injection system with a flexible common rail direct injection system. An advanced start of fuel injection (SOI) and exhaust gas recirculation (EGR) are required to achieve PCCI in the test engine. Parametric investigations on SOI, EGR and fuel injection pressure are carried out to identify optimum parameters for achieving maximum brake thermal efficiency. An SOI sweep of 12 to 50 deg. CA bTDC is done and for each SOI, EGR is varied from 0 to 50% to identify maximum efficiency points. It was found that EGR helps in extending the load range from 20 to 40% of rated load.

Reactivity Controlled Compression Ignition (RCCI) is a promising, high-efficiency, clean combustion mode for diesel engines. One of the significant limitations of RCCI is its higher unburned hydrocarbon (HC) and carbon monoxide (CO) emissions compared to conventional diesel combustion. After-treatment control of HC and CO emissions is difficult to achieve in RCCI because of lower exhaust gas temperatures associated with the low-temperature combustion (LTC) mode of operation. The present study involves combined experimental and computational fluid dynamic (CFD) investigations to develop the most effective HC and CO control strategy for RCCI. A production light-duty diesel engine is modified to run in RCCI mode by introducing electronic port fuel injection with the replacement of mechanical injectors by the CRDI system. Experimental data were obtained using diesel as HRF (High reactive fuel) and gasoline as LRF (low reactive fuel).

Mass-production single-cylinder engines are generally not turbocharged due to pulsated exhaust flow. Hence, about one-third of the fuel chemical energy is wasted in the engine exhaust. To extract the exhaust energy and boost the single-cylinder engines, a novel supercharging with a turbo-compounding strategy is proposed in the present work, wherein an impulse turbine extracts energy from the pulsated exhaust gas flow. Employing an impulse turbine for a vehicular application, especially on a single-cylinder engine, has never been commercially attempted. Hence, the design of the impulse turbine assumes higher importance. A nozzle, designed as a stator part of the impulse turbine and placed at the exhaust port to accelerate the flow velocity, was included as part of the layout in the present work. The layout was analyzed using the commercial software AVL BOOST. Different nozzle exit diameters were considered to analyze their effect on the exhaust back pressure and engine performance.

Almost one-third of the fuel energy is wasted into the atmosphere via exhaust gas from an internal combustion engine. Despite several advancements in waste heat recovery technology, single-cylinder engines in the market that are currently in production remain naturally aspirated without any waste heat recovery techniques. Turbocharging is one of the best waste heat recovery techniques. However, a standard turbocharger cannot be employed in the single-cylinder engine due to technical challenges such as pulsated flow conditions at the exhaust, phase lag in the intake and exhaust valve opening. Of late, the emphasis on reducing exhaust emissions has been a primary focus for any internal combustion engine manufacturer, with the onset of stricter emission norms. Thus, the engine designer must prioritize emission reduction without compromising engine performance.