Search Results

This study investigates simultaneous improvement in thermal efficiency and cooling loss in the wider operating condition. To suppress the heat flux of the piston, the piston top and cavity were treated with thin thermal spraying of stainless steel. Thermal diffusivity of stainless steel (X5CrNiMo17-12-2, SUS316) is very low in comparison with the forged steel piston raw material (34CrMoS4, SCM435) to sustain local surface temperature at where spray flame directly interfered. In addition, its surface roughness was very fine finished aiming to reduce the convective heat transfer. The experimental results with the stainless-steel coated piston by utilizing a single cylinder engine showed the significant improvement in both cooling loss and thermal efficiency even in higher load operating conditions with compression ratio of 23.5:1.

The emissions reduction potential of neat GTL (Gas to Liquids: Fischer-Tropsch synthetic gas-oil derived from natural gas) fuels has been preliminarily evaluated by three different latest-generation diesel engines with different displacements. In addition, differences in combustion phenomena between the GTL fuels and baseline diesel fuel have been observed by means of a single cylinder engine with optical access. From these findings, one of the engines has been modified to improve both exhaust emissions and fuel consumption simultaneously, assuming the use of neat GTL fuels. The conversion efficiency of the NOx (oxides of nitrogen) reduction catalyst has also been improved.

Improvement in heat loss could be an important factor to increase the brake thermal efficiency (BTE) of an internal combustion engine; however, the heat energy saved isn’t all converted to brake work. Theoretically, to increase the conversion efficiency of heat energy into indicated work, the compression (or expansion) ratio and specific heat ratio (γ) are important. Nevertheless, γ has not been well-studied thus far, since it can’t be easily controlled. This study utilized a two-zone model to calculate the time-resolved γ and local excess air ratio of the burned gas (λb), which varied with the heat release rate. The two-zone combustion model, in which the cylinder volume is simply separated into burned and unburned zones to simulate the overall diesel combustion phenomena, was developed to investigate the current status of heterogeneous (diesel) combustion compared to ideal homogeneous combustion.

To overcome the trade-offs of thermal efficiency with energy loss and exhaust emissions typical of conventional diesel engines, a new diffusion-combustion-based concept with multiple fuel injectors has been developed. This engine employs neither low temperature combustion nor homogeneous charge compression ignition combustion. One injector was mounted vertically at the cylinder center like in a conventional direct injection diesel engine, and two additional injectors were slant-mounted at the piston cavity circumference. The sprays from the side injectors were directed along the swirl direction to prevent both spray interference and spray impingement on the cavity wall, while improving air utilization near the center of the cavity.

To reduce carbon dioxide (CO2) emissions from heavy-duty diesel engines down to zero until 2050, alternative powertrain strategies have been proposed in lieu of the improvements in internal combustion engines (ICEs). However, total amount of renewable electricity could be limited for the constructing infrastructure, the production of new battery and/or fuel cell vehicles and the operation of them compared with the growing demand of transportation in the future. Therefore, drastic improvement in transport efficiency with suppressing the increase of total CO2 emissions is essential. From these points of view, extremely high efficiency ICEs, combined or at least compatible with carbon neutral or renewable fuels having the capability of drop-in into the conventional fuels, should be attracted attention. Nevertheless, there have been few studies on the effects of fuel properties for further improving fuel consumption of diesel ICEs.

Cooling loss reduction is essential to enable further increases in thermal efficiency of reciprocating internal combustion engines. Many in-cylinder cooling loss reduction studies have been carried out by applying various thermal barrier coatings to the piston and/or other in-cylinder surfaces, taking advantage of the lower thermal effusivity of ceramic materials. However, the end result was mostly minimal or in some cases, negative. In our previous study, significant cooling loss reduction was experimentally confirmed by utilizing a mirror-like polished stainless-steel thermal sprayed surface (HVOF: high velocity oxy-fuel) on a forged steel piston. This study firstly investigated an alternative insulating layer material to stainless-steel, along with effects of its thickness on heat transfer by a one-dimensional unsteady numerical model. Results showed that lower thermal effusivity doesn’t always reduce heat transfer, but increases nonuniformity of surface temperature.

This study focused on the technology integration to aim beyond 60% indicated thermal efficiency (ITE) with a single-cylinder heavy-duty diesel engine as an alternative to achieve 55% brake thermal efficiency (BTE) with multiple-cylinder engines. Technology assessment was initially carried out by means of a simple chart of showing ITE and exhaust heat loss as functions of cooling loss and heat conversion efficiency into indicated work. The proposed compression ratio (28:1), excess air ratio and new ideal thermodynamic cycle were then determined by a simple cycle calculation. Except for peak cylinder pressure constraint for each engine, the technical barriers for further ITE improvement are mainly laid in cooling loss reduction, fuel-air mixture formation improvement, and heat release rate optimization under very high temperature and density conditions with very high compression ratio (smaller cavity volume).