Search Results

Fuel-borne catalysts are now an accepted means of aiding the self-regeneration of diesel particulate filters (DPFs). In the past it has been possible to assess the effect of these fuel additives by investigating the temperature at which the filter reaches a pressure drop equilibrium. Under these temperature conditions, the particulate matter is oxidised at the same rate as it is being deposited and there is thus no change in pressure drop across the filter. This technique adequately demonstrates the oxidation temperature of the carbon in the presence of the catalyst. However, it is now well known that such fuel additives also influence the low temperature oxidation of particulate bound hydrocarbons. This phenomenon is not detected by the filter equilibrium technique.

Current developments in fuels and emissions regulations are resulting in increasingly severe operating environment for the injection system. Formation of deposits within the holes of the injector nozzle or on the outside of the injector tip may have an adverse effect on overall system performance. This paper provides a critical review of the current understanding of the main factors affecting deposit formation. Two main types of engine test cycles, which attempt to simulate field conditions, are described in the literature. The first type involves cycling between high and low load. The second involves steady state operation at constant speed either at medium or high load. A number of influences on the creation of deposits are identified. This includes fouling through thermal condensation and cracking reactions at nozzle temperatures of around 300°C. Also the design of the injector holes is an influence, because it can influence cavitation.

Four vehicles were chosen to cover a range of engine technologies. These vehicles were fitted with diesel particulate filters (DPFs) of differing technology. Three of the vehicles have been driven on the road using an additised fuel to demonstrate totally passive operation of the DPF. As part of this programme all three vehicles underwent regulated emissions testing to demonstrate that there was no deterioration in emissions during the programme. Additionally a light commercial vehicle was tested to demonstrate the effect on emissions of the combination of additised fuel and the DPF. The performance of the DPFs during on-road use has already been reported; this paper therefore concentrates on discussion of the results of the emissions testing.

Forthcoming emissions legislation is driving the passenger car manufacturers towards the fitting of Diesel Particulate Filters (DPFs) as original equipment. However such initiatives are not retrospective and due to the replacement rate of the vehicle fleet, there is a time lag before the full benefit of the new measures are fully realised. To overcome this drawback, in areas with a particular problem such as heavily congested city centres, retrospective legislation has been introduced, for example in Hong Kong and Tokyo. Legislation mandating the retrofitting of DPFs obviously has an immediate effect on particulate emissions. Other authorities are thus investigating the efficacy of such measures. To add to the data base for such assessments Octel is running a demonstration programme using London Black Cabs. Four cars have been fitted with a DPF, an on-board dosing system to meter a fuel borne catalyst (FBC) into the fuel and a data logger to monitor the DPF performance.

Forthcoming emissions legislation is driving the passenger car manufacturers towards the fitting of Diesel Particulate Filters (DPFs) as original equipment. In areas with a particular problem such as heavily congested city centres, retrospective legislation has also been introduced, for example in Hong Kong and Tokyo. Legislation mandating the retrofitting of DPFs obviously has an immediate effect on particulate emissions. Other authorities are thus investigating the efficacy of such measures. However with the increasing use of DPF technology concerns are now being raised over some currently unregulated emissions such as ultra fine particulate and NO2, although total particulate mass and oxides of nitrogen are regulated. To add to the data base for such issues a programme of work was run using London Black Cabs. Four cars were fitted with a DPF, an on-board dosing system to meter a fuel borne catalyst (FBC) into the fuel and a data logger to monitor the DPF performance.

Current developments in fuels and emissions regulations are resulting in an increasingly severe operating environment for diesel fuel injection systems. The formation of deposits within the holes or on the outside of the injector nozzle can affect the overall system performance. The rate of deposit formation is affected by a number of parameters, including operating conditions and fuel composition. For the work reported here an accelerated test procedure was developed to evaluate the relative importance of some of these parameters in a high pressure common rail fuel injection system. The resulting methodology produced measurable deposits in a custom-made injector nozzle on a single-cylinder engine. The results indicate that fuels containing 30%v/v and 100% Fatty Acid Methyl Ester (FAME) that does not meet EN 14214 produced more deposit than an EN590 petroleum diesel fuel.

Recent developments in diesel engines and fuel injection equipment combined with the change to ULSD and bio-blends have resulted in increased reports regarding deposits within injectors and filters. A review of known fuel degradation mechanisms and other relevant chemistries suggests the effects of high pressure and high shear environments should be examined as the most probable causes of increasing deposit formation. Existing fuel quality tests do not correlate with reported fouling propensity. Analytical studies have shown that there are only subtle chemical changes for the materials within the standard diesel boiling range. The implications for further scientific study are discussed.

Traditionally, diesel fuel injection equipment (FIE) has frequently relied on the diesel fuel to lubricate the moving parts. When ultra low sulphur diesel fuel was first introduced into some European markets in the early 1980's it rapidly became apparent that the process of removing the sulphur also removed other components that had bestowed the lubricating properties of the diesel fuel. Diesel fuel pump failures became prevalent. The fuel additive industry responded quickly and diesel fuel lubricity additives were introduced to the market. The fuel, additive and FIE industries expended much time and effort to develop test methods and standards to try and ensure this problem was not repeated. Despite this, there have recently been reports of fuel reaching the end user with lubricating performance below the accepted standards.

The atomisation characteristics of DI diesel engine fuel injection nozzles have been the subject of intensive study over the last decade. Much of this work has been related to clean, single hole nozzles spraying into quiescent air, at either ambient conditions or elevated pressures and temperatures. Experience shows that fuel injector nozzles may foul very rapidly in field service, and that this might have a significant effect on the performance of the engine particularly with regard to emissions. The build up of material on the injector nozzle can be controlled by the addition of suitable fuel additives. This paper describes test procedures developed to assess deposit build up and to indicate the efficacy of keep clean additives. The paper then goes on to describe high speed photographic techniques for studying the fuel spray characteristics of clean and fouled injectors in a firing engine.

Trapping diesel particulates is effective in reducing both the number and the mass of fine particulate emissions from diesel engines, but unless the accumulated soot can be burned out or regenerated periodically, the vehicle to which the trap is fitted will cease to function after a relatively short time. A programme of work with soot traps using a low treat rate iron-strontium organo-metallic fuel additive to assist and secure regeneration has been carried out. As part of this programme, an advanced specification diesel engine passenger car equipped with a diesel particulate filter (DPF), was operated on roads in the UK for approximately 18 months, during which time the vehicle covered over 50,000 km After completion of 50,000 km on roads, the vehicle was operated on a chassis dynamometer to increase the distance covered with a DPF more rapidly to a final total of 80,000 km.