Search Results

The active engine mount (AEM) is developed in automotive industry to improve overall NVH performance. The AEM is designed to reduce major-order signals of engine vibration over a broad frequency range, therefore it is of vital importance to extract major-order signals from vibration before the actuator of the AEM works. This work focuses on a method of real-time extraction of the major-order acceleration signals at the passive side of the AEM. Firstly, the transient engine speed is tracked and calculated, from which the FFT method with a constant sampling rate is used to identify the time-related frequencies as the fundamental frequencies. Then the major-order signals in frequency domain are computed according to the certain multiple relation of the fundamental frequencies. After that, the major-order signals can be reconstructed in time domain, which are proved accurate through offline simulation, compared with the given signals.

With increasing pressure for reduction in CO2 emissions and stricter fuel targets from road vehicles, OEMs around the globe have to electrify their vehicle range to meet increasingly challenging emission standards in recent years and new transmission technologies are gaining more attention in different main markets. The actual and future powertrain development has three major directions in order to reduce or avoid emissions in the transportation sector: Hybrid Vehicles: Hybrid Electric Vehicles (HEV), Plug-in HEV (PHEV) Electric Vehicles (EV); Range Extender Electric Vehicle (REEV); Fuel Cell Electric Vehicles (FCEV), Range Extender FCEV (REFCEV). This paper presents a new type Hybrid transmission which is called “DHT (Dedicated Hybrid Transmission)” technology for cost-effective HEVs and PHEVs; it permits the design of very compact automatic transmissions with an integrated high-voltage electric motor on the output side of the transmission.

CORUN CHS has recently developed a new power-split hybrid transmission platform CHS-HT2800, which has added 2 clutches compared to CHS-HT1800. With involvement of 2 E-motors CHS-HT2800 has 9 forward gears, including 3 electric forward gears and 6 hybrid forward gears. Among the 6 hybrid gears 4 gears are fixed-ratio gears and the remaining 2 gears are eCVT gears. This paper describes a strategy, designed for CHS-HT2800, how to select the optimal mode, the optimal gear and the optimal work point of the engine to achieve the best economy performance in the real traffic. Because it is universally accepted, that the WLTC cycle can represent real world vehicle operation on urban and extra-urban roads, motorways, and freeways. The introduced strategy will be validated with the help of the WLTC cycle.

With increasing pressure from environment problem for reduction in CO2 emissions and stricter fuel targets from road vehicles, new transmission technologies are gaining more attention in different main market. To get suitable road load data for transmission durability development is becoming increasingly important and can shorten the development time of new transmission. This paper presents the procedure and methods of road load data development for durability design of transmission product and optimization based on the real road data measurement, statistical characteristics evaluation and fatigue damage equivalency. Apply this road load data method procedure on 3 type of vehicle which represent conventional vehicle, BEV and HEV.

Tire cavity noise of pure electric vehicles is particularly prominent due to the absence of engine noise, which are usually eliminated by adding Helmholtz resonators with arbitrary transversal section to the wheel rims. This paper provides theoretical basis for accurately predicting and effectively improving acoustic performance of wheel resonators. A hybrid finite element method is developed to extract the transversal wavenumbers and eigenvectors, and the mode-matching scheme is employed to determine the transmission loss of the Helmholtz resonator. Based on the accuracy validation of this method, the matching design of the wheel resonators and the optimization method of tire cavity noise are studied. The identification method of the tire cavity resonance frequency is developed through the acoustic modal test. A scientific transmission loss target curve and fitness function are defined according to the noise characteristics.

The backlash between engaging components in a driveline is unavoidable, especially when the gear runs freely and collides with the backlash, the impact torque generated increases the vibration amplitude. The power-split hybrid electric vehicle generates output torque only from the traction motor during the launching process. The nonlinear backlash can greatly influence the driveability of the driveline due to the rapid response of the traction motor and the lack of the traditional clutches and torsional shock absorbers in the powertrain. This paper focuses on the launch vibration of the power-split hybrid electric vehicle, establishes a nonlinear driveline model considering gear backlash, including an engine, two motors, a Ravigneaux planetary gear set, a reducer, a differential, a backlash assembly, half shafts, and wheels.

Active engine mounts (AEMs) notably contribute to ensuring superior performance of vehicle’s noise, vibration, and harshness. This paper incorporates a filtered-x-least-mean-squares (FxLMS) controller into the active control engine mount system to attenuate the transmitted force to the body. To avoid the error caused by substituting the load cell for acceleration transducer, the FIR model of the secondary path was obtained by experiment. Finally, a hardware-in-the-loop testing system is built to verify the performance of the active engine mount. It can be observed from the test results that the vibration is reduced notably after control, which demonstrates the effectiveness of the active engine mount and the controller in vibration attenuation.

Manufacturers have been encouraged to accommodate advanced downsizing technologies such as the Variable Displacement Engine (VDE) to satisfy commercial demands of comfort and stringent fuel economy. Particularly, Active control engine mounts (ACMs) notably contribute to ensuring superior effectiveness in vibration attenuation. This paper incorporates a PID controller into the active control engine mount system to attenuate the transmitted force to the body. Furthermore, integrated time absolute error (ITAE) of the transmitted force is introduced to serve as the control goal for searching better PID parameters. Then the particle swarm optimization (PSO) algorithm is adopted for the first time to optimize the PID parameters in the ACM system. Simulation results are presented for searching optimal PID parameters. In the end, experimental validation is conducted to verify the optimized PID controller.

The turbocharger air intake noise during transient conditions like wide open throttle and tip-in/out affects the passenger ride comfort. This paper aims to study an optimized design of multi-chamber perforated resonators to attenuate this noise. The noise produced by a turbocharger in a test vehicle has been measured to find out the noise spectral characteristics which can be used to design the acoustic targets including the amplitude and frequency range of transmission loss (TL). The structural parameters of the resonators are optimized based on genetic algorithm (GA) and two-dimensional prediction theory of the resonator TL. The optimized resonators are installed on the test vehicle to verify the actual noise reduction effect. The results suggest that the broadband noise has been eliminated, and subjective feelings are greatly improved.

X-in-the-loop (XiL) framework is a validation concept for vehicle product development, which integrates different virtual and physical components to improve the development efficiency. In order to develop and validate an extended validation method based on XiL, Tongji University in Shanghai, China and the Karlsruhe Institute of Technology (KIT) in Karlsruhe, Germany co- performed a feasibility study about an X-in-the-distance-loop demonstration platform. The X-in-the-distance-loop demonstration platform includes a MATLAB/Simulink software platform and geographically distributed equipment (driver simulator, driving electric motor and dynamometer test stand), which are used to conduct bidirectional experiments to test communication of powertrain data between China and Germany.

Hydrogen safety is of great importance in proton exchange membrane fuel cell (PEMFC) systems. Anode pressure control has become a focus point in recent years. The differential pressure between anode and cathode in PEMFC system needs to be carefully controlled under a suitable threshold. In practice, the anode pressure is usually controlled about 20–30kPa higher than the cathode pressure to minimize nitrogen crossover and improve cell stability. High differential pressure could lead to irreversible damage in proton exchange membrane. PID control was the dominant method to control the anode pressure in the past. However, the anode pressure’s fluctuation when hydrogen mass flow suddenly changes is a long-term challenge. As the requirements of control precision are increasingly high, the traditional PID control needs to be improved. Several new control algorithms are presented in recent researches, however, mostly are theoretical and experimental.

Because a compound power-split transmission is directly connected to the engine, dramatic fluctuations in engine output torque result in strong jerks and torque losses when the hybrid vehicle is in mode transition from electric drive mode to hybrid drive mode. In order to enhance ride comfort and reduce the output torque gap during mode transition process, a brake clutch assisted coordinated control strategy was developed. Firstly, the dynamic plant model of the power-split vehicle including driveline model, engine ripple torque and brake clutch torque was deduced. Secondly, the brake clutch assisted mode transition process was analyzed, and the output torque capability was compared between cases of both brake clutch assisted and unassisted mode transition process. Thirdly, a coordinated control strategy was designed to determine the desired motor torque, brake clutch torque, engine torque, and the moment of fuel injection.

Active engine mount (AEM) is an effective approach which can optimize the noise, vibration and harshness (NVH) performance of vehicles. The filtered-x-least-mean-squares (FxLMS) algorithm is widely applicated for vibration attenuation in AEMs. However, the performance of FxLMS algorithm can be deteriorated without an accurate secondary path estimation. First, this paper models the secondary path using finite impulse response (FIR) model, infinite impulse response (IIR) model and back propagation (BP) neural network model and the model errors of which are compared to determine the most accurate and robust modeling method. After that, the influence of operation frequency on accuracy of the secondary path model is analyzed through simulation approach. Then, the impact of reference signal mismatch on the control effect is demonstrated to study the robustness of FxLMS algorithm.

A novel compound power-split hybrid transmission based on a modified Ravigneaux gear set is presented. The equivalent lever diagrams are used to investigate the electric operating modes for the hybrid powertrain, and then its dynamic and kinematic characteristics as well as efficiency characteristics are described in equations. A brake clutch mounted on the carrier shaft is proposed to enhance the electric driving efficiency for the hybrid transmission. Three types of electric operating mode are analyzed by the simplified combined lever diagrams and the system efficiency and torque characteristics for these electric operating modes are compared. A major influence on output torque of the hybrid transmission derived from the torque capability of motors and brake clutch is depicted.

Because of the direct connection between the compound power split hybrid transmission (CPSHT) and the engine in hybrid electric vehicle (HEV), engine ripple torque (ERT) can lead to obvious jerks when the mode transition from electric driving mode to hybrid driving mode occurs. In order to enhance the riding comfort, two additional wet clutches are mounted in this novel CPSHT and the relevant coordinated control strategy is developed. Firstly, after the description of the mechanical and hydraulic parts of the novel CPSHT, the dynamic plant model including driveline model, engine ripple torque and clutch torque is deduced. Secondly, the mode transition process in the original and current designs are compared and analyzed with the equivalent level diagram and the encountered problems are stated.

In this paper the approach of using modal parameters to detect and locate damage of automobile rear axle under experimental condition is explained. This method uses the changes in the curvature mode of the structure as the damage identification indicator to detect and locate damage. The curvature mode and the damage identification indicator are explained, the process of the identification is introduced. The method is demonstrated with a FEM (Finite Element Method) analysis on a plate under different damage conditions. And the indicator is improved with a weighting function. Then EMA (Experimental Modal Analysis) is conducted on a damaged and an undamaged rear axle of a vehicle to get the modal parameters for the damage identification indicator which later identifies and locates the damages, thus validating the introduced method.

Several types of power-split hybrid transmissions are outlined and the strengths and weaknesses of typical compound power-split prototype designs are summarized in this paper. Based on an modified Ravigneaux gear set, a novel compound power-split hybrid transmission with compact mechanical structure is presented, its dynamic and kinematic characteristics in equations and operating modes are described, and then equivalent lever diagrams are used to investigate the proposed compound power-split device. Control strategies in different operating modes are discussed with the simplified combined lever diagram, and a global optimization method is implemented to find the optimum operation point for the hybrid powertrain. To evaluate the fuel economy of a hybrid car equipped with this hybrid transmission, a forward powertrain simulation model is developed and real vehicle performance tests are conducted in the chassis dynamometer.

The flow issues of the turbocharged intake system for a diesel engine are mainly introduced in this work and the effects of a multi-chamber perforated resonator which can efficiently attenuate broadband noise and has compact structure on the flow performances of the intake system is analyzed by contrast. Based on the acoustic grid resulting from pre-processing of 3D models for finite element analysis, a computational fluid dynamics flow simulation comparative analysis between the intake systems with and without a resonator including pressure and velocity distribution is conducted with the software Star-CCM+. The simulation results indicate that the air pressure drop of the intake system with a resonator is slightly higher than that of the intake system without a resonator but it is still relatively low compared with that of the entire intake system.

The statement of the engine shake problem is presented through comparing the quarter vehicle models with the rigid-connected and flexible-connected powertrain which is supported on the body by a rubber mount. Then the model is extended by replacing the rubber mount as a hydraulic engine mount (HEM) with regard to the inertia and resistance of the fluid within the inertia track. Based on these, a full vehicle model with 14 degree of freedoms (DOFs) is proposed to calculate the engine shake, which consists of 6 of the powertrain, 1 of the fluid within the inertia track of the HEM, 3 of the car body and 4 of the unsprung mass. Simulation analysis based on the proposed model is implemented, through which the conclusion is drawn that the HEM has great influence on the body and seat track response subjected to front wheel inputs, compared with the rubber mount.

In order to research the vibration and noise reduction in pure electric vehicle power-train, a comprehensive work is to simulate the power-train incentive of a high-speed pure electric vehicle, and indicates significant impact of gear mesh system on the power-train NVH performance. Therefore, it is necessary to further study the impact of meshing gear system on electric vehicle power-train vibration and noise performance and seek reasonable methods to reduce the vibration and noise. In this paper, a typical pure electric vehicle's powertrain was used to conduct vibration and noise dynamic simulation. Firstly, the power train model was established considering the gear meshing stiffness, transmission errors, bearing factors and shell flexible, then the vibration and sound radiation dynamic response of power-train was simulated. Based on the accuracy of prediction model, a gear tooth modification was carried out for vibration and noise optimization.