Search Results

The University of Maryland Space Systems Laboratory has developed a system that replicates some limited aspects of pressure suits to facilitate neutral buoyancy research into EVA bioinstrumentation, advanced EVA training, and EVA/robotic interactions. After a two year upgrade from its MX-1 predecessor, the MX-2 space suit analogue is currently undergoing a variety of system integration tests in preparation for initial operational testing, leading to routine use for EVA simulation and as a testbed for advanced space suit technology. The MX-2 is built around a hard upper torso with integrated hemispherical helmet and rear-entry hatch. Three-layer soft-goods are used for the arms and lower torso, while an open loop air system regulates suit pressure to 3 psid. Wrist disconnects allow the use of standard EMU or Orlan gloves, or experimental gloves such as the mechanical counterpressure gloves and power-assisted gloves developed previously by the SSL.

Real time knowledge of the metabolic workload of an astronaut during an Extra-Vehicular Activity (EVA) can be instrumental for space suit research, design, and operation. Three indirect calorimetry approaches were developed to determine the metabolic workload of a subject in an open-loop space suit analogue. A study was conducted to compare the data obtained from three sensors: oxygen, carbon dioxide, and heart rate. Subjects performed treadmill exercise in an enclosed helmet assembly, which simulated the contained environment of a space suit while retaining arm and leg mobility. These results were validated against a standard system used by exercise physiologists. The carbon dioxide sensor method was shown to be the most reliable and a calibrated version of it will be integrated into the MX-2 neutral buoyancy space suit analogue.

The research discussed in this paper demonstrates further advancements in the concept of a Morphing Upper Torso, which incorporates robotic elements within the pressure suit design to enable a resizable, highly mobile and easy to donn/doff spacesuit. A full scale experimental model has been made, which accompanies several analytical models. The Jacobian matrix for the robotic system, which multiplies the total twist vector of the system to yield the vector of actuator velocities, is derived. This dynamic analysis enables quantification of the dynamic actuator requirements, given demanded trajectories of the rings. A motion capture pilot study was done to develop a methodology to obtain measurements of suit movement and hence the ring trajectories. Subjects performed various tasks that a suited astronaut may perform on a planetary surface, while wearing a torso mockup within the motion capture system.

There has recently been an increasing focus on humans working cooperatively with robotic systems in space exploration and operations. Considerable work has been performed on distributed architectures to enable such interaction. The research described here looks at the human-robot interaction from the EVA astronaut's perspective, describing a first generation human-machine interface implemented and tested on an existing experimental spacesuit analog, the MX-2. The ultimate goal is to enable EVA astronauts to operate more independently of remote operators and work effectively with autonomous and teleoperated robots. The current system integrates speech interaction and visual interfaces as a first step towards this goal.

The fit of a spacesuit has been identified as a crucial factor that will determine its usability. Therefore, because one-size-fits-all spacesuits seldom fit any wearer well, and because individually tailored spacesuits are costly, the University of Maryland has conducted research into a resizable Extravehicular Activity (EVA) suit. This resizing is accomplished through a series of cable-driven parallel manipulators, which are used to adjust the distance between plates and rings built into a soft space suit. These actuators, as well as enabling passive suit resizing, could be used to actively assist the astronaut's motion, decreasing the torques that must be applied for movement in a pressurized suit. This paper details the development and testing of an arm prototype, which is used to better understand the dynamics of a more complex torso-limb system.

This paper describes a unique concept for donning and doffing a spacesuit from a pressurized rover or habitat, which merges three independent concepts: suitports, neck-entry EVA suits, and the Morphing Upper Torso. The union of these concepts creates a novel and exciting suit and suitport system architecture, with many potential benefits over traditional suitport systems. To develop this concept, a neck-entry Morphing Upper Torso experimental model has been designed and fabricated, and systems level design studies have been performed, including visualization with the aid of CAD models of the neck-entry suitport on a small pressurized rover and a lunar habitat. As well, a donning test-station has been developed and used for experiments in 1-G, simulated microgravity and simulated partial gravity.

Performance of new space suit designs is typically tested quantitatively in laboratory tests, at both the component and integrated systems levels. As the suit moves into neutral buoyancy testing, it is evaluated qualitatively by experienced subjects, and used to perform tasks with known times in earlier generation suits. This paper details the equipment design and test methodology for extended space suit performance metrics which might be achieved by appropriate instrumentation during operational testing. This paper presents a candidate taxonomy of testing categories applicable to EVA systems, such as reach, mobility, workload, and so forth. In each category, useful technologies are identified which will enable the necessary measurements to be made. In the subsequent section, each of these technologies are examined for feasibility, including examples of existing technologies where available.

Employing a cooperative human and robotic team has the potential to greatly reduce human workload during space missions and create more efficient operational teams. The Hubble Space Telescope Servicing Mission 3A tasks were assessed and modeled with three different human and robot team pairings to elucidate the difference to team performance. Tasks were allocated to the standard two-human EVA crew and a robotic agent for each of the cases. The schedules reduce the human crew's involvement time in each EVA day's activities by rearranging subtasks to minimize the human crew's wait time. This work examines three agent participation scenarios and their effect on the expected efficiency of the cooperative team during mission activities.

Future space missions will involve humans and robots cooperatively performing operational tasks in various team combinations. Part of the required preparation for such missions includes understanding the issues involved in task allocation between disparate agents, and efficiently ordering tasks within the mission constraints. The scheduling tool developed in this research distributes pre-allocated task primitives between a cooperative human crew and dexterous robotic team. It combines real-world precedent constraints with algorithms from scheduling theory to reorder and tighten each crew member's individual schedule. The schedules minimize astronaut involvement time by stacking astronaut-performed tasks together in the schedule. This also minimizes astronaut workload in the completion of each task. Hubble Space Telescope Servicing Mission 3A was used as an example to test the allocation and scheduling tool.